Climate change gains more from nuclear substitution than from conservation

We show the massive reduction achievable, in both emissions and climate change impact, from enhanced nuclear energy use on the forecasts of future world energy use and its associated environmental impacts. A range encompassing the major scenarios for the World's energy demand have been analyzed using the latest version of the climate-modeling MAGICC/SCENGEN software (Version 4.1). We have updated and predicted the impacts of 80% substitution with CO₂-free sources (likely predominantly nuclear) for coal-fired electricity (by 2030) and for transportation fuel (by 2040). For transportation, hydrogen produced by CO₂-free sources would replace gasoline and diesel fuels. In this paper, to bracket the range of futures, we simply focus on two scenarios from the Intergovernmental Panel on Climate Change's (IPCC), one (A1FI) that is energy-profligate and one (B2) that is energy-conserving.The results show that, interestingly, projected average global temperatures for all scenarios are fairly similar until about 2035 (a further rise beyond the 1990 average temperature of +0.75 ± 0.1 K) regardless of energy usage and its sources. However, by 2050, the different IPCC scenarios diverge markedly. Understandably, A1FI is projected to have noticeably stronger effects than B2 on average global temperatures (about 0.3 K more in 2050) but the effect is much stronger over land at mid and high latitudes (up to almost 1 K more). What is most striking is that the substitution of CO₂-free sources gives projected average temperature rises in 2050 over key land areas (North America and China) that are very similar for the two energy-use scenarios—typically 1–1.5 K because A1FI's additional energy is predominantly supplied by nuclear. In contrast, projected rises with the unaltered cases are markedly different being about 2.5 K for A1FI and 1.5–2 K for B2. The projected changes in rainfall distribution show similar patterns, especially for the expected increases in higher latitudes.With the assumption of no additional policies for substitution of energy sources beyond 2040, temperature divergence between the two scenarios of relative energy profligacy or conservation grows in the latter half of the 21st century, even with substitution. However, the early substitution of nuclear energy and hydrogen appears to buy time and is not crucially dependent on severe, near-term curtailment of energy use. Near-term curtailment is too difficult to implement at a time of rapid industrialization of major emerging economies. Of course, proportionately larger deployments of CO₂-free energy sources are needed for more energy-intensive scenarios.Nuclear power must dominate as the source of CO₂-free energy since it is proven, dependable, available on a large scale, and economic. Social objections to nuclear energy in some countries and quarters are seen as well-meaning but misguided distractions from solving the energy and environmental crises that are now facing world sustainability. The time for real technical, social and political action is now.     

Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

The appropriateness of the systematic framework to develop diagnosis procedures of nuclear power plants—an experimental verification

It has been well recognized that a diagnosis procedure that allows operators to successfully identify the nature of an on-going event is inevitable for an effective and appropriate recovery. Unfortunately, studies for a framework that can suggest a unified and consistent process in constructing a serviceable diagnosis procedure seem to be scant. Thus, Park et al. have suggested a systematic framework that can be used to construct a useful diagnosis procedure. In addition, the diagnosis procedure that is currently in use at the reference nuclear power plant (NPP) is reformed in order to demonstrate the appropriateness of the suggested framework. However, the necessity of a well-designed experiment is proposed to confirm the appropriateness of the suggested framework.In this regard, in this study, an experiment is conducted using a full-scope simulator of the reference NPP. From the experiment, two sets of operators' diagnosis performance data are collected, and then they are compared to investigate the change of an operator's diagnosis performance with respect to two types of diagnosis procedures.As a result, it is shown that an operator's diagnosis performance is improved when the revised diagnosis procedure is used. Therefore, it is reasonable to conclude that the suggested framework is useful in constructing an effective diagnosis procedure.     

In-Situ and Real-Time Investigation of Columnar-to-Equiaxed Transition in Metallic Alloy

In this article, we present a review of observations during Al-3.5 wt pct Ni alloy solidi.cation experiments performed at the European Synchrotron Radiation Facility (ESRF) in Grenoble. These experiments provide direct access to dynamical phenomena during columnar growth (initial transient and breakdown of a planar solid-liquid interface), and for the first time to the transition from columnar-to-equiaxed microstructure (nucleation ahead of a columnar front and blocking of a columnar front by an equiaxed microstructure) and fully equiaxed growth (propagation of an effective front). Based on these experimental observations, critical parameters such as columnar growth velocity variation during the transition or equiaxed-grain diameter are measured and discussed. This article is based on a presentation made in the symposium entitled “Solidi.cation Modeling and Microstructure Formation: In Honor of Prof. John Hunt,” which occurred March 13–15, 2006, during the TMS Spring Meeting in San Antonio, Texas, under the auspices of the TMS Materials Processing and Manufacturing Division, Solidification Committee.     

Formation of C4 species in the deactivation of a Pd/SiO2 catalyst during the selective hydrogenation of acetylene

The deactivation characteristics of Pd/SiO₂ in the selective hydrogenation of acetylene were correlated with changes in the amount of the C4 species produced. The amounts of butenes produced changed in parallel with the catalyst activity, indicating that the rate limiting step for butene production was the same as that for acetylene hydrogenation. On the other hand, the amount of 1,3-butadiene produced changed, showing a maximum with catalyst deactivation because 1,3-butadiene is an intermediate in the sequential reaction process which involves both the production and consumption of 1,3-butadiene. This was verified by a simultaneous TG/reaction experiment showing that 1,3-butadiene was a precursor of green oil. The catalyst showed a self-regenerative behavior in its activity and the amounts of C4 species produced during the early stage of deactivation because two opposite factors, which contributed to either the lowering or the promotion of activity, were involved in the process. A specific type of polymer species, produced during the initial period of deactivation, is proposed to be responsible for the promotion of catalyst activity.     

Growth hormone response to growth hormone-releasing factor in selected and control Holstein heifer calves

Holstein heifer calves from selected and control lines were treated with growth hormone-releasing factor to determine whether the magnitude of the pituitary growth hormone response is associated with genetic potential for milk yield. Cows in the selected line were bred to highest Predicted Difference milk sires available each year, while control line cows were bred to bulls that were average for 1964 milk production. Eight calves from each line of similar age (206 to 210 days) and weight (205 kg average) were injected intravenously with .1 microgram/kg growth hormone-releasing factor. Dams' first lactation 305-day mature equivalent records were 10,192 +/- 495 kg for selected calves and 6,908 +/- 376 kg for control calves. Before treatment, GH tended to be higher in selected than control calves (mean +/- SE: selected = 7.5 +/- 1.8, control = 4.6 +/- .4 ng/ml). After injection, peak GH were reached within 20 min and were similar in selected and control calves, averaging 66 +/- 16 and 73 +/- 13 ng/ml, respectively. Results indicate that the magnitude of the growth hormone response to growth hormone-releasing factor is not related to future performance of dairy calves.     

Learning spreadsheets: human instruction vs. computer-based instruction

The increasing need to instruct students in the use of personal computer software, especially electronic spreadsheets, is placing greater demands on the already full university curriculum. A potential help in meeting these demands is the readily available computer-based software tutorials. In order to explore the feasibility of computer-based instruction as an alternative to human instruction, this research compares two modes of instruction, computer-based and human. An experiment was conducted with groups of business student subjects. The research results indicate no difference in students' attitude towards computer-based instruction and human instruction of spreadsheets. Students' short-term recall of the software syntax being taught is as strong with computer-based instruction as with human instruction. These results were not affected by the level of personal computer experience that students had prior to the experiment. However, the ability to comprehend and immediately apply the software to a task is greater with human instruction than with computer-aided instruction. This advantage holds true for students instructed by experienced and inexperienced instructors.     

Factors affecting the activity of anammox bacteria during start up in the continuous culture reactor.

Factors affecting cultivation of extremely slow-growing bacteria (anaerobic ammonium oxidiser, doubling time 11 days) were investigated by using upflow anaerobic sludge blanket (UASB) reactors which can maintain high solid retention time. The effects of concentrations of DO, free ammonia (FA), and nitrite on activation of anammox activity were tested during the start-up period. The reactor was inoculated with granular sludge collected from a full-scale UASB reactor used for treating brewery wastewater, and sludge from a piggery wastewater treatment plant and rotating biological contactor treating sewage. Results of continuous operation showed that concentrations of DO, free ammonia (FA) and nitrite in the reactors played a key role in stimulating the anammox activity during start-up period. It is crucial to keep DO below 0.2 ppm, FA below 2 mg/L and nitrite nitrogen below 35 mg/L to cultivate anammox cells in the continuous bioreactor. When the levels of DO, FA and nitrite in the influent were controlled at less than the inhibition levels, the anammox activity increased gradually in the anaerobic condition. Addition of hydrogen sulphide into the reactor enhanced anammox activity in the continuous culture. Through the SEM, TEM and FISH analysis, anammox bacteria were detected in the granular sludge after 3 months of continuous operation.