Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

Predeployed secure key distribution mechanisms in sensor networks: current state-of-the-art and a new approach using time information

In this article we survey a number of predeployed secure key distribution (PSKD) schemes proposed in the technical literature. We also propose a new time-based PSKD (TPSKD), which operates under the assumption of loose time synchronization, and discuss the performance of the scheme. Since the TPSKD scheme uses time information, which would typically already be available in sensor nodes, the cost of the scheme?s implementation is low.     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Effect of vibration condition and inter-particle frictions on the packing of uniform spheres

We present a numerical study of the packing of uniform spheres under three-dimensional vibration using the discrete element method (DEM), focusing on the effects of vibration condition (amplitude and frequency) and inter-particle frictions (sliding and rolling frictions). The results are analysed in terms of packing density, coordination number (CN), radial distribution function (RDF) and pore structure. It is shown that increasing either the vibration amplitude or frequency causes packing density to increase initially to a maximum and then decrease. Both vibration frequency and amplitude should be considered to characterize the effect of vibration process on packing structure. The sliding and rolling frictions between particles can decrease packing density since they dissipate energy, although the effect of rolling friction is less significant. In line with the change of packing density, microstructural properties such as CN, RDF and pore distribution also change: a looser packing often corresponds to smaller CN, less peaked RDF and larger but more widely distributed pores.     

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

Modelling biological processes under anaerobic conditions through integrating titrimetric and off-gas measurements-applied to EBPR systems.

An innovative method for modelling biological processes under anaerobic conditions is presented and discussed. The method is based on titrimetric and off-gas measurements. Titrimetric data is recorded as the addition rate of hydroxyl ions or protons that is required to maintain pH in a bioreactor at a constant level. An off-gas analysis arrangement measures, among other things, the transfer rate of carbon dioxide. The integration of these signals results in a continuous signal which is solely related to the biological reactions. When coupled with a mathematical model of the biological reactions, the signal allows a detailed characterisation of these reactions, which would otherwise be difficult to achieve. Two applications of the method to the enhanced biological phosphorus removal processes are presented and discussed to demonstrate the principle and effectiveness of the method.