Maximum likelihood-based adaptive differential evolution identification algorithm for multivariable systems in the state-space form

Parameter estimation plays an important role in the field of system control. This article is concerned with the parameter estimation methods for multivariable systems in the state-space form. For the sake of solving the identification complexity caused by a large number of parameters in multivariable systems, we decompose the original multivariable system into some subsystems containing fewer parameters and study identification algorithms to estimate the parameters of each subsystem. By taking the maximum likelihood criterion function as the fitness function of the differential evolution algorithm, we present a maximum likelihood-based differential evolution (ML-DE) algorithm for parameter estimation. To improve the parameter estimation accuracy, we introduce the adaptive mutation factor and the adaptive crossover factor into the ML-DE algorithm and propose a maximum likelihood-based adaptive differential evolution algorithm. The simulation study indicates the efficiency of the proposed algorithms.     

干巴菌多糖提取工艺优化及抗氧化活性的研究

以产于云南曲靖的干巴菌为原料,以多糖提取率为评价指标,采用单因素实验及正交实验优化干巴菌多糖的提取工艺,通过测定干巴菌多糖对DPPH自由基及羟基自由基的清除率来评价其抗氧化活性。结果表明,干巴菌多糖的最佳提取工艺为:提取温度70℃、提取时间2.5 h、料液比1∶15(g∶mL),在此条件下,多糖提取率达到10.08%;当干巴菌多糖浓度为5 mg·mL~(-1)时,其对DPPH自由基的清除率为86.99%,对羟基自由基的清除率为87.46%,有较好的抗氧化作用。     

Comparative study of Fourier transform infrared spectroscopy (FTIR) analysis of natural fibres treated with chemical,physical and biological methods

Polymer Bulletin - Kenaf and luffa fibres are hydrophilic due to the presence of water sensitive constituents, which tend to form a poor compatibility when binding with polymers. Thus, the surface...     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

铜离子掺杂对高铁低钙水泥熟料性能的影响

基于C4AF可以提高水泥基材料的抗蚀性,以高铁低钙水泥熟料为研究对象,掺入不同含量的CuO,通过对熟料及其水化产物进行X射线衍射(XRD)、水化热、抗压强度、非蒸发水含量和固化氯离子能力等测试,探究Cu2+对高铁低钙水泥熟料水化性能与氯离子吸附固化能力的影响.结果发现,适量CuO的掺入促进了高铁低钙水泥熟料中C4AF的生成,降低了熟料液相的粘度,有利于C3S的晶粒生长,有利于提高高铁低钙水泥熟料的水化活性和固化氯离子能力,最佳掺量为0.2 wt％.     

区域导航对流层延迟误差修正模型研究

本文研究了电波大气折射理论，分析了传播误差因素，阐述了区域导航信号的传播路径与 GNSS 卫星导航的不同，论述了对流层延迟对区域导航信号测量精度的影响，设计了满足区域导航系统应用需求的对流层延迟误差修正模型，并通过仿真研究，验证了所设计区域导航对流层延迟误差修正模型的可行性，并给出了该模型在远距离低仰角和近距离高仰角下的误差修正能力。     

Fabrication of Cu/graphite film/Cu sandwich composites with ultrahigh thermal conductivity for thermal management applications

Effective thermal management of electronic integrated devices with high powder density has become a serious issue, which requires materials with high thermal conductivity (TC). In order to solve the problem of weak bonding between graphite and Cu, a novel Cu/graphite film/Cu sandwich composite (Cu/GF/Cu composite) with ultrahigh TC was fabricated by electro-deposition. The micro-riveting structure was introduced to enhance the bonding strength between graphite film and deposited Cu layers by preparing a rectangular array of micro-holes on the graphite film before electro-deposition. TC and mechanical properties of the composites with different graphite volume fractions and current densities were investigated. The results showed that the TC enhancement generated by the micro-riveting structure for Cu/GF/Cu composites at low graphite content was more effective than that at high graphite content, and the strong texture orientation of deposited Cu resulted in high TC. Under the optimizing preparing condition, the highest in-plane TC reached 824.3 W·m⁻¹·K⁻¹, while the ultimate tensile strength of this composite was about four times higher than that of the graphite film.     

单次反射ATR-FTIR红外光谱法在涂膜表面成分分析中的应用

运用傅里叶变换衰减全反射红外光谱法(ATR-FTIR)中的单次反射法对水性偏氯乙烯-丙烯酸酯共聚物薄膜进行辅助定性研究,考察了具有不同偏氯乙烯单体含量的共聚物薄膜的红外谱图变化。同时运用单次反射ATR-FTIR法对施工现场取回的红色脱落涂膜进行定性分析。     

2014年聚酯产业链供需状况及发展趋势

介绍了聚酯产业链供需现状,对未来几年聚酯产业链发展趋势做了分析和研究,并提出相关建议。