DX型数据采集与无线传输系统

DX型数据采集与无线传输系统能对油井压力、温度、载荷和流量等参数进行自动采集 ,并通过无线传输向总站提供实时参数 ,为及时决策提供信息。数据采集系统采用STD总线 ,测量精度高、故障低 ;无线传输系统采用短波电台和具有自动纠错功能的数传机 ,抗噪能力强、可靠性高。文章介绍了DX型数据采集与无线传输系统的组成、工作原理、功能和主要技术指标     

New polymer syntheses: 59. Homo-and copolyesters of 4-(4′-hydrophenoxy)benzoic acid

The homopolyester of 4-(4′-hydroxyphenoxy)benzoic acid (poly(4-HPBA)), was prepared under two different reaction conditions and compared with a sample provided by another research group. Depending on the synthetic route, different melting points, d.s.c. traces and crystal lattices were found. However, after repeated heating and cooling, one thermodynamically stable modification with a melting point of 370–375°C can be obtained. Copolyesters of 4-hydroxybenzoic acid and 4-(4′-hydroxyphenoxy)benzoic acid were prepared with various molar ratios either in the melt (condensation in bulk) or in solution. These copolyesters were characterized by elemental analyses, ¹H n.m.r. spectroscopy, d.s.c. measurements, wide-angle X-ray scattering measurements at various temperatures, and optical microscopy. Whereas copolyesters prepared in solution do not melt below 500°C, those prepared by polycondensation in bulk show melting points down to approximately 260°C and form a nematic melt.     

鱼雷罐喷粉预处理优化研究

在已经得到的描述鱼雷罐喷粉处理基本参数具体表达式的基础上，运用多目标非线性优化方法，对工艺操作参数进行优化。     

一种制备插层和无定形高岭土的新方法

利用甲醇钠强烈的夺氢作用 ,介绍了一种制备插层和无定形高岭土的方法。利用XRD为主要检测手段研究了甲醇钠的质量分数、反应温度等因素对反应的影响。结果表明 :在反应温度较低、质量分数较低的甲醇钠溶液中 ,高岭土容易被插层而膨胀 ,反之高岭土的层状结构被破坏而无定形化。红外光谱分析进一步证明了插层和无定形高岭土结构的变化     

Dielectric barrier discharge treatments at atmospheric pressure for wood surface modification

In this research, the effect of dielectric barrier discharge on mechanically manufactured (sawn, planed or polished) wood surfaces is investigated. The experiments have shown that the best hydrophilia is obtained with a cold plasma discharge in air under atmospheric pressure. Other gases such as helium, nitrogen, and argon have been tested, too. Changes of the wood surface properties were determined by absorption of water and contact angle measurements. As a result of a 1 to 20 seconds long exposure to plasma, wood surfaces became hydrophilic. The absorption of water in wood can be changed up to 22 times higher after plasma treatment in air for 20 seconds duration. The fracture strength of glued wood has been increased by 68% after this plasma pretreatment. Using plasma treatment in methane or acetylene wood surfaces are changed to hydrophobic properties. After plasma treatment for 1 min. in a Ar:CH₄=80:20 gas mixture under atmospheric pressure, the absorption of water in wood is 32 times lower than without plasma treatment. As mentioned before, plasma treatment can produce hydrophobic and hydrophilic wood surfaces. But a good homogeneity of the gas discharge is necessary for the plasma treatment of wood. Zusammenfassung Im Rahmen dieser Arbeit werden die Auswirkungen der dielektrisch behinderten Entladung bei Atmosphärendruck auf mechanisch bearbeitete Holzoberflächen (gesägt, gehobelt oder geschliffen) untersucht. Die Experimente haben gezeigt, dass die höchste Hydrophilität bei einem in Luftatmosphäre gezündetem Plasma erreicht wird. Es werden auch andere Gase verwendet, wie z.B. Helium, Stickstoff und Argon. Zur Untersuchung der veränderten mechanischen und energetischen Eigenschaften der Holzoberflächen werden der Tropfen-Versuch und die Kontaktwinkelmessung verwendet. Durch eine 1 bis 20 Sekunden lange Plasmabehandlung können die Oberflächen hydrophil gestaltet werden. So kann die Eindringzeit von Wasser um Faktor 22 gesteigert werden durch eine 20 Sekunden lange Plasmabehandlung in Umgebungsluft. Die Bruchfestigkeit von Leimholz wird durch die gleiche Plasmavorbehandlung um 68% gesteigert. Werden als Plasmabehandlungsgas Methan oder Acetylen eingesetzt, so wird die Holzoberfläche hydrophob. Durch eine 60 Sekunden lange Plasmabehandlung in einem Ar:CH₄=80:20 Gasgemisch bei Atmosphärendruck wird die Eindringszeit von Wasser um den Faktor 32 gesenkt. Mit Hilfe der Plasmabehandlung können also sowohl hydrophobe als auch hydrophile Holzoberflächen erzeugt werden. Jedoch wird für die Plasmabehandlung von Holz eine sehr homogene Gasentladung benötigt.     

超声波处理石油污水的实验研究

考察了在不同空化状态下超声波对石油污水化学耗氧量(COD)的降低作用。探讨了时间、功率、pH值及温度对石油污水化学耗氧量降低作用的影响。结果表明，石油污水化学耗氧量的降低率随着时间增大而增大，随着温度、pH值的增加而减小，随着功率的增加，先增加，然后再减小。     

砼坝裂缝稳定性分析

通过比较线弹性断裂力学中的两种计算应力强度因子的方法，外推法和奇异单元法，得到相应的结论；并以某砼坝下游部位出现裂缝为例，分析在不利荷载作用下裂缝的稳定性。     

On the current delivery limit of semiconducting carbon nanotubes

The current carrying capacity of single-walled semiconducting carbon nanotubes (CNTs) is studied by self-consistent quantum simulations using the non-equilibrium Green’s function formalism with the self-consistent Born approximation. The simulation shows that the current carrying capacity depends on the bias regime and is drastically different from that of metallic tubes. For long CNTs (with a length much longer than zone boundary and optical phonon scattering mean free path), the current saturates around 20 μA in the forward bias regime with unipolar transport due to phonon scattering. In ambipolar transport regime, the current delivery limit is still about 20 μA due to recombination of electron and hole currents. In contrast, for short semiconducting CNTs, the current delivery capacity can be above 25 μA in the unipolar transport regime and further double in the ambipolar transport regime. In reverse bias regime, the current of a long CNT can exceed 20 μA due to the second subband conduction and increased electron injection from the drain. The simulation provides a coherent explanation to the dependence of current delivery limit on bias regime and channel length, which is consistent with recent experiments.     

叠后地震剖面的线性化波阻抗反演

本文提出了由井旁道出发逐道进行的叠后地震剖面的线性化波阻抗反演方法。每一道反演采用逐次线性化对波阻抗进行修正，反演的纵向分辨率为一个采样时间间隔，并以合成记录道与实际地震道的相似系数作为迭代收敛准则，已处理的地震道波阻抗作为下一道反演初始值。实际资料处理表明，该方法具有较高的分辨率和运算速度快的优点。     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.