AlMg10合金铸造零件表面缺陷成因探析

点蚀等表面缺陷会最终导致铝合金的失效.运用金相、扫描电镜、能谱、光谱以及化学分析等多种手段,研究了AlMg10合金零件表面缺陷的形貌和成分.结果表明,该零件表面缺陷主要为表面点蚀及皮下气孔.点蚀主要是因为表层及表面中含有较多的氯、硫等元素.讨论了皮下气孔形成的机理,认为皮下气孔中的夹杂来自熔体中尺寸接近或小于某一临界尺寸的异质相质点;凹槽形核机制是皮下气孔形核的主要机制,合金熔体凝固时的收缩为气孔形核和长大提供了驱动力.     

消失模铸造金属液在型内的流动

消失模铸造金属液在填充铸型初期的流动接近失重状态,且直浇道越高越接近失重态.消失模铸造浇注系统开放或封闭的判据是:单位时间内浇注系统提供的金属液大于等于泡沫退让的体积为封闭式,当金属液小于泡沫退让的体积时为开放式.     

冷却介质对ZG30CrMn2Si2NiMo组织和力学性能的影响

研究了不同冷却介质对ZG30CrMn2Si2NiMo铸钢力学性能及组织的影响.试验结果表明,奥氏体化后空冷ZG30CrMn2Si2NiMo组织为板条贝氏体型铁素体和残余奥氏体组织,奥氏体化后淬火ZG30CrMn2Si2NiMo组织为板条马氏体、贝氏体型铁素体和残余奥氏体组织.ZG30CrMn2Si2NiMo获得板条马氏体、贝氏体型铁素体和残余奥氏体组织时,具有良好的力学性能.     

高铁三水铝石型铝土矿的烧结特性

以Al2O3含量为26.35%,总Fe含量为31.22%,铝硅比为3.17的某高铁三水铝石型铝土矿为原料,研究了碱度、焦粉用量、混合料水分等对烧结矿质量指标的影响。结果表明:烧结矿碱度增加时,其转鼓强度和成品率下降,烧结矿自粉化程度加重;焦粉用量增加时,烧结矿转鼓强度和成品率提高;当混合料水分为9.0%、焦粉用量为8.0%、烧结矿碱度为4时,烧结矿转鼓强度为69.1%,成品率为81.2%,垂直烧结速度为30 mm/min,利用系数为1.2 t/(h.m2);烧结矿碱度为4时,样品存放2天粉化率为5%,烧结矿平均粒度由22.2 mm减小到21.9 mm,延长存放时间,烧结矿自粉化率增大,平均粒度显著减小。该烧结矿的冶金性能能基本满足高炉冶炼的要求。     

基于网络文本的山地景观游客行为与形象感知研究——以重庆市长嘉汇弹子石老街为例

剖析网络评价文本能为景观规划设计提供科学的依据支撑,弥补因快速城镇化建设发展而导致的公众参与不足,对于景观设计而言是非常重要的。以重庆市弹子石老街为例,基于网络文本内容分析法,利用rostcm6、excel及python等分析和数据抓取软件,采集大众点评的相关评论数据,以山地景观设计视角结合相关数据分析软件进行定性定量分析并制作可视化分析图,最终从多维度分析游客评论得出结果及改进建议,总结针对重庆弹子石老街及山地景观设计的6条设计策略:(1)交通可达的组织方式;(2)垂直上下的衔接转换;(3)对景远眺的外向空间;(4)本土文化的特色彰显;(5)城市事件的策划安排;(6)游览夜景的慢行系统,期望对今后的类似山地景观空间规划设计提供一定参考和借鉴价值。     

多模型系统的神经网络控制器设计

针对多模型不确定系统,文章给出利用神经网络同时逼近多个常规控制器,实现多模型控制的神经网络控制方法.仿真实验结果表明了该方法简单有效,鲁棒性强.     

电感电容损耗电阻的讨论

通过对电容电感阻抗的测量，发现实验值偏离理论值。定性地分析了误差的来源，得出的结论是电感电容内部的损耗电阻随着频率的变化而变化，变化方向相反而并非相同。     

Magnetic and mechanical properties of FeSi alloys with high Si content

The chemical vapor（CVD） deposition-diffusion method was applied to prepare FeSi alloys with high silicon content up to 6.5%. In spite of various deposition and post-annealing, the sample remains α-Fe bcc structure. The cross section of the composition was analyzed to evaluate the Si content and distribution before and after annealing. The results show that the soft magnetic properties are improved by increasing the silicon content. For the samples containing about 6.5% Si, the coercivity decreases to 60 from 237.3 A/m of the original. It is also obtained that, in addition to the Si content, Si distribution has a large influence on the core loss due to the effect of resistivity. The micro-hardnesses were also evaluated along the cross-section after various annealings.     

搅拌摩擦加工(FSP)AZ91D镁合金的组织分析

研究了AZ91D镁合金经搅拌摩擦加工后的组织。发现组织中搅拌摩擦区、热机械影响区和热影响区分区不明显。在搅拌摩擦区主要为再结晶形成的细小均匀的等轴晶结构,共晶组织α-Mg β相(Mg17Al12)完全均匀化,仅在晶界处有少量存在。     

Preparation of alumina-doped yttria-stabilized zirconia nanopowders by microwave-assisted peroxyl-complex coprecipitation

Alumina-doped yttria-stabilized zirconia （ADYSZ） nanopowders were prepared by microwave-assisted peroxyl-complex coprecipitation （MAPCC） using ZrOCl2-8H2O, Y2O3 and AICly6H2O as starting materials, NH2-H2O as precipitant and H2O2 as complexant. The effects of adding H2O2 and microwave drying on the preparation and properties of ADYSZ were investigated. The precursors and nanopowders were studied by EDX, XRD, SEM and TEM techniques. The results show that the uniformity of component distribution within ADYSZ nanopowders is improved by adding appropriate dosage of H2O2. Complexing reaction between H2O2 and Zr^4＋ ion restrains the hydrolyzation and precipitation of Zr^4＋ ion. With the addition of H2O2, Al^3＋, y^3＋ and Zr^4＋ ions can be precipitated synchronously in a relatively narrow range of pH value. H2O2 also improves the filterability of the wet precipitate. The highly hydrophilic precipitates can be quickly and effectively separated from aqueous solution. During microwave drying process, the moisture of wet precursors is selectively heated. Quick expansion of steam vapor within the wet colloidal particles causes the aggregations burst into numerous tiny lumps. Compared with oven drying, microwave drying can not only shorten drying time but also reduce aggregation intensity of the resultant ADYSZ nanopowders.