石英玻璃飞秒激光微连接及其接头性能

飞秒激光的低热输入、极小热影响区的特点使其在微米尺度材料连接领域有明显的应用潜力。为研究飞秒激光进行玻璃连接的可行性及其接头性能,测定了其接头的拉剪强度并分析了接头断裂前后的形貌特征。证明了飞秒激光连接玻璃的可行性,并发现玻璃试样之间的间隙对飞溅有明显影响。拉剪试验测得的接头强度在6.4~40.4MPa之间。结果表明,在激光平均功率较大,焊缝间距较小的条件下,连接试样容易在母材中断裂,使得接头的强度相比于断裂在界面上的试样强度降低一半以上。     

工程塑料的进展

从聚合工艺、共混、合金化、填充、增强、复合的制备技术等方面,简要论述了今后工程塑料,特别是改性复合型工程塑料的主要发展方向。     

新型储氧、储氮材料——Ba掺杂的CeO2-ZrO2固溶体

利用“超声膜扩散法”制备了系列Ba掺杂的CeO₂-ZrO₂固溶体,研究了Ba掺杂对CeO₂-ZrO₂固溶体的热稳定性和储放氧能力的影响,并测量了Ba掺杂CeO₂-ZrO₂固溶体材料的储存NOx性能。结果表明,随着Ba含量的增加,固溶体的储氧量先增加后降低,在Ce_0.5Zr_0.5O₂·xaO系列固溶体中,当x=0.16时,样品储氧量达到最大,新鲜样品的储氧量可达到745 μmol·g^-1,样品的NO储量随含Ba量的增加而线性增加。     

Cracking in poly(trimethylene terephthalate) spherulites

The crack behavior of poly(trimethylene terephthalate) spherulites was studied mainly by polarizing optical microscopy, along with scanning electron microscopy (SEM) and atomic force microscopy (AFM). In addition to the effects of temperature and constraining substrate, another important factor, film thickness, on the formation of crack was first put forward and investigated. The emergence of the first crack occurred at 120°C during cooling after crystallization at 190°C for the sample with a thickness of 31.0 μm. For the spherulites growing between glass sheets, it was interesting that the sample with a thickness of 26.0 μm exhibited the largest number of cracks measured per 200 μm of radius, whereas samples thicker than 100 μm or thinner than 1 μm did not induce the formation of crack. Also, spherulites growing between two polyimide and two Teflon sheets showed no crack. Glass sheets lubricated with silicon oil restrained the number of cracks but did not eliminate cracks. SEM revealed that the cracking was about 900 nm in width. In addition, the AFM results suggest that the cracks had a depth of at least 150 nm. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and properties of homogeneously dispersed polyamide 6/MWNTs nanocomposites via simultaneous in situ anionic ring‐opening polymerization and compatibilization

Toluene 2, 4‐diisocyanate (TDI) functionalized multiwalled carbon nanotubes (MWNTs‐NCO) were used to prepare monomer casting polyamide 6 (MCPA6)/MWNTs nanocomposites via in situ anionic ring‐opening polymerization (AROP). Isocyanate groups of MWNTs‐NCO could serve as AROP activators of ?‐caprolactam (CL) in the in situ polymerization. Fourier transform infrared (FTIR) showed that a graft copolymer of PA6 and MWNTs was formed in the in situ polymerization. MWNTs‐PA6 covalent bonds of the graft copolymer constituted a strong type of interfacial interaction in the nanocomposites and increased the compatibility of MWNTs and MCPA6 matrix. The nanocomposites were characterized for the morphology, mechanical, crystallization, and thermal properties through field emission transmission electron microscopy (FETEM), tensile testing, differential scanning calorimeter (DSC), and thermogravimetric analysis (TGA). FETEM analysis showed that MWNTs were homogeneously dispersed in MCPA6 matrix. The initial tensile strengths and tensile modulus of the nanocomposite with 1.5 wt % loading of MWNTs were enhanced by about 16 and 13%, respectively, compared with the corresponding values for neat MCPA6. DSC analysis indicated that the crystallization temperature of the nanocomposites was increased by 8°C by adding 1.5 wt % MWNTs compared with pure MCPA6. Besides, it was found that the thermal stability of MCPA6 was improved by the addition of the MWNTs. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

四针状氧化锌晶须对聚丙烯力学性能及抗菌性能的影响

采用偶联剂KH-570对四针状氧化锌晶须(T-ZnOw)进行表面改性,制备了聚丙烯(PP)/改性T-ZnOw复合材料。对复合材料进行了X射线衍射分析,并考察了T-ZnOw含量对复合材料力学性能和抗菌性能的影响。结果表明:T-ZnOw在PP基体中结晶良好;适量添加经过表面改性的T-ZnOw能提高复合材料的拉伸强度、断裂伸长率和弯曲强度;在T-ZnOw含量为4%时,复合材料即可达到国家规定的抗菌要求。     

Melting behaviors,isothermal crystallization kinetics,and morphology of poly(trimethylene terephthalate)/stainless steel fiber composites

The melting behavior and crystallization kinetics of poly(trimethylene terephthalate) (PTT)/stainless steel fiber (SSF) composites were investigated with differential scanning calorimetry. The morphology was studied with scanning electron microscopy and polarized optical microscopy. Differential scanning calorimetry analysis revealed that the crystallization temperature increased by 27°C with the addition of 1 vol % SSF to the matrix. The Avrami exponents, analyzed in isothermal crystallization kinetics, were determined to be 2–3 for both neat PTT and PTT/SSF composites. SSF, as a nucleating agent in the composites, greatly increased the crystallization rate. The activation energies of the composites were obviously lower than that of pure PTT, and this indicated much easier crystallization of the composites. All these samples exhibited banded spherulites, and the spherulite size gradually decreased with the SSF loading increasing. Subsequent melting behaviors revealed that all of these samples, especially of the composites, exhibited triple melting peaks at all crystallization temperatures studied. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

HDPE chelate membranes prepared by preirradiation grafting for adsorption of heavy metal ions

A new chelate membrane was prepared by grafting of glycidyl methacrylate (GMA) onto high‐density polyethylene membranes and subsequent amination of poly‐GMA graft chains. The effects of grafting conditions such as radiation dose and temperature on grafting yield were studied. Effects of various parameters such as grafting yield, pH, and adsorption time on the metal uptake were investigated. The results show that the maximum metal uptake followed as given in the order Cr (III)>Fe (III)>Cu (II)>Cd (II). The metal uptake increased with grafting yield, adsorption time, pH of the medium, and initial concentration. The chelated metal ions are easily desorbed with 0.1 mol/L hydrochloric acid at room temperature. The results obtained from the chelate membrane showed a promising application in extraction of heavy metal ions from industrial effluents. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

虚拟数控加工过程的研究

采用虚拟加工技术,设计了双刀架数控车床的虚拟数控加工系统,介绍了一种三维动画仿真技术及其特点。     

高铬白口铸铁中碳当量对抗磨性能的影响

高铬白口铸铁的共晶显微组织与普通白口铸铁的共晶组织不同,其中不连续的条块状共晶铁、铬碳化物M7C3占25%左右,与富铬的二次碳化物位于金属基体奥氏体或其转变产物中,而后者的M3C碳化物能占到48%,可看作渗硫体基体或海锦状渗碳体,里面镶嵌奥氏体转变产物,所以共晶型高铬白口铸铁的韧性比普通共晶型白口铸铁好,共晶组织中碳化物的短小空间对共晶奥氏体基体起到良好的保护作用,在高应力磨料磨损条件下,过共晶高铬白口铸铁中的大块状初生M7C3碳化物能很好地抵抗磨粒对抗磨件施加的法向压力和切向剪切力,不易断裂,故而抗磨性能较好.