Annular‐ring slot antenna designs with circular polarization radiation

The design of a microstrip‐fed annular‐ring slot antenna (ARSA) with circular polarization (CP) radiation is initially studied. To obtain CP radiation with broad 3‐dB axial ratio (AR) bandwidth that can cover the WiMAX 2.3 GHz (2305–2320 MHz, 2345–2360 MHz) and WLAN 2.4 GHz (2400–2480 MHz) bands, a novel technique of extending an inverted L‐shaped slot from the bottom section of the annular‐ring is proposed. To suppress the harmonic modes induced by the CP ARSA, the technique of integrating a defected ground structure into the annular‐ring slot is further introduced. From the measured results, 10‐dB impedance bandwidth and 3‐dB AR bandwidth of 44.86 and 9.68% were achieved by the proposed harmonic suppressed CP ARSA. Furthermore, average gain and radiation efficiency of ～4.7 dBic and 71%, respectively, were also exhibited across the bands of interest. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:337–345, 2015.     

Preparation and physicochemical study of jute and glass composites of epoxy resin of (2E, 6E)-bis(4-hydroxybenzylidene)cyclohexanone

Polymer Bulletin - Jute and glass composites of epoxy resin of (2E, 6E)-bis(4-hydroxybenzylidene)cyclohexanone (EBHBC) were prepared by compressing molding technique using three different hardeners...     

Bamboo biochar-catalytic degradation of lignin under microwave heating

Abstract

Lignin biochar-catalytic depolymerization using biochar Fe-600, Fe-800, Ni-600, Ni-800 catalysts under microwave-heating (180?°C for 30?min) was explored in an ethanol/formic acid (1:1) media. Non-catalyst depolymerization was also studied and compared with the biochar-catalysts results. Characteristics of the bio-char catalysts were analyze by BET, XRD, and FT-IR. GPC, FT-IR, and MALDI-TOF MS spectrometry were also used to characterize the depolymerization products. The experimental results showed that the S_BET, V_t, and V_mec and average pore diameter of the biochars are considerably dependent on the preparation temperature and type of cation (Ni²⁺ or Fe³⁺). The maximum yield of bio-oil product was obtained as 85?wt% with the addition of biochar Ni-600 and the total amount of oligomers or monomers with a molecular weight of 164 to 446 reaches 80.4%.     

The Critical Role of Passive Permeability in Designing Successful Drugs

Passive permeability is a key property in drug disposition and delivery. It is critical for gastrointestinal absorption, brain penetration, renal reabsorption, defining clearance mechanisms and drug-drug interactions. Passive diffusion rate is translatable across tissues and animal species, while the extent of absorption is dependent on drug properties, as well as in vivo physiology/pathophysiology. Design principles have been developed to guide medicinal chemistry to enhance absorption, which combine the balance of aqueous solubility, permeability and the sometimes unfavorable compound characteristic demanded by the target. Permeability assays have been implemented that enable rapid development of structure-permeability relationships for absorption improvement. Future advances in assay development to reduce nonspecific binding and improve mass balance will enable more accurately measurement of passive permeability. Design principles that integrate potency, selectivity, passive permeability and other ADMET properties facilitate rapid advancement of successful drug candidates to patients.     

Synthesis and Application of Novel Nano Fe-BTC/GO Composites as Highly Efficient Photocatalysts in the Dye Degradation

Topics in Catalysis - Nano Fe-BTC/graphene oxide (GO) composites were successfully synthesized by hydrothermal treatment with a microwave-assisted method. Samples were characterized by X-ray...     

Similarities and differences between male and female novice designers on color‐concept associations for warnings,action required,and signs and equipment status messages

This research examined the male and female novice designers toward color associations for the concepts used for ‘warnings’, ‘action required’, and ‘signs and equipment status’ through a questionnaire‐based study. A total of 178 Hong Kong Chinese final year undergraduate design students (89 males and 89 females) participated in the study. The test used required the participants to indicate their choice of one of nine colors to associations with each of 38 concepts in a color‐concept table, so that any one color could be associated with any one of the concepts. For both male and female groups of novice designers, chi‐square tests revealed a strong color association for each concept tested in this study (P < .05). The results showed males and females agreed on some color‐concept association stereotypes which were therefore gender neutral. The male and female novice designers had the same color associations and similar levels of stereotype strengths for 21 concepts. The nine strongest and therefore most useful color‐concept association stereotypes for both male and female novice designers were: red‐danger, red‐fire, red‐hot, red‐stop, red‐emergency, red‐error, blue‐cold, blue‐male, and green‐exit. However, the male and female novice designers had different color association stereotypes for the standby (green vs. yellow), emergency exit (green vs. red), and toxic (purple vs. black) concepts, and the strengths of the 14 remaining associations for both groups were not at equivalent levels. Overall, it is anticipated that the findings of this study will act as a useful reference for novice designers and other design practitioners to optimize color coding in the design of ‘warnings’, ‘action required’, and ‘signs and equipment status’ messages.     

CuInS2/SiNWs/Si composite material for application as potential photoelectrode for photoelectrochemical hydrogen generation

This work aims at developing a new composite material based on nanosized semiconducting CuInS₂ (CIS) particles combined with silicon nanowires grown on a silicon substrate (SiNWs/Si) for photoelectrochemical (PEC)-splitting of water. The CIS particles were prepared via a colloidal method using N-methylimidazole (NMI) as the solvent and an annealing treatment. The SiNWs were obtained by chemical etching of silicon (100) substrates assisted by a metal. The CIS/SiNWs/Si composite material was obtained by deposition of an aliquot of a suspension of CIS particles onto the SiNWs/Si substrate, using spin coating followed by a drying step. The XRD pattern demonstrated that CuInS₂ grows in the tetragonal/chalcopyrite phase, while SiNWs/Si presents a cubic structure. The SEM images show semi-spherical particles (～10 nm) distributed on the surface of silicon nanowires (～10 μm). The EIS measurements reveal n-type conductivity for CIS, SiNWs/Si and CIS/SiNWs/Si materials, which could favour the oxidation reaction of water molecules.     

Moderate lameness leads to marked behavioral changes in dairy cows

Lameness is one of the most prevalent diseases affecting the welfare of cows in modern dairy production. Lameness leads to behavioral changes in severely lame cows, which have been investigated in much detail. For early detection of lameness, knowledge of the effects of moderate lameness on cow behavior is crucial. Therefore, the behavior of nonlame and moderately lame cows was compared on 17 Swiss dairy farms. On each farm, 5 to 11 nonlame (locomotion score 1 of 5) and 2 to 7 moderately lame (locomotion score 3 of 5) cows were selected for data collection in two 48-h periods (A, B) separated by an interval of 6 to 10 wk. Based on visual locomotion scoring, 142 nonlame and 66 moderately lame cows were examined in period A and 128 nonlame and 53 moderately lame cows in period B. Between these 2 periods, the cows underwent corrective hoof trimming. Lying behavior, locomotor activity, and neck activity were recorded by accelerometers (MSR145 data logger, MSR Electronics GmbH, Seuzach, Switzerland), and feeding and rumination behaviors by noseband sensors (RumiWatch halter, ITIN + HOCH GmbH, Liestal, Switzerland). Furthermore, visits to the brush and the concentrate feeder, and the milking order position were recorded. In comparison with nonlame cows, moderately lame cows had a longer lying duration, a longer average lying bout duration, and a greater lateral asymmetry in lying duration. Average locomotor activity, locomotor activity during 1 h after feed delivery or push-ups, and average neck activity were lower in moderately lame cows. Eating time and the number of eating chews (jaw movements) were reduced in moderately lame compared with nonlame cows, whereas no effect of moderate lameness was evident for ruminating time, number of ruminating chews and boluses, and average number of ruminating chews per bolus. Moderately lame cows visited the concentrate feeder and the brush less frequently, and they were further back in the milking order compared with nonlame cows. In conclusion, nonlame and moderately lame cows differed in a biologically relevant way in many of the behavioral variables investigated in this study. Therefore, the use of these behavioral changes seems to be promising to develop a tool for early lameness detection.