Characterization of new FIR laser lines from CHD/sub 2/OH

In this work, we report new optically pumped far-infrared (FIR) laser lines from CHD/sub 2/OH. A waveguide CO/sub 2/ laser of wide tunability (290 MHz) was used as pump source, and a Fabry-Pe/spl acute/rot open cavity was used as a FIR laser resonator. Optoacoustic absorption spectra were used as a guide to search for new FIR laser lines. We could observe 15 new laser lines in the range from 116.4 to 401.4 /spl mu/m. The lines were characterized according to wavelength, relative polarization, relative intensity, and optimum working pressure. The transferred Lamb-dip technique was used to measure the frequency absorption transition both for the new and previously reported laser lines.     

Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

Final Drying of Whole Milk Powder in Vibrated-Fluidized Beds

Vibro-fluidized beds are widely used in drying sticky powders and agglomerated materials as milk powder. Using a vibro-fluidized laboratory scale dryer, this work is aiming at analyzing preliminarily the effect of its operational variables on the drying kinetics and characteristics of whole milk powder. The full-factorial design technique with three replications at the central point has been employed to generate data and correlations to quantify the effect of inlet air temperature, air flow rate, and vibration bed amplitude on the drying curves and the milk powder properties related to its faster reconstitution in water (as tapped density, Hausner cohesion ratio, agglomerate size distribution, and internal pore concentration). Results obtained are analyzed and discussed to identify the adequate operation condition for final drying whole milk powder in vibro-fluidized beds, assuring a high product quality.     

Infrared and ultraviolet–visible spectroscopic studies of silica, [(Cp)2ZrCl2] and trimethylaluminum interactions

Infrared and UV–vis studies of metallocene immobilization on silica are reported here. The results have indicated changes in the Zr coordination sphere of metallocene depending on the immobilization route used. The reaction of [(Cp)₂ZrCl₂] with silica formed [(Cp)₂ZrCl]⁺[SiO]⁻ species. The same metallocene, reacting with TMA modified silica, formed monomethylated and dimethylated species by the substitution of chloro for methyl ligands, stabilized on the surface by interaction with “MAO-like” species (methylaluminoxane, MAO). These monomethylated and dimethylated cationic zirconium species are the active centers for the polymerization reaction. Different order of TMA addition in the silica modification step generated surface species of a similar nature, differing in their relative quantities. The highest amount of these active species was obtained when the support was added to the TMA solution rather than adding the TMA solution to the silica support. This was the most significant parameter affecting catalytic activity in ethylene polymerization.     

Optical and electrical characterization of fluorine doped cadmium oxide thin films prepared by the sol-gel method

Highly transparent and conducting fluorine (F) doped cadmium oxide (CdO) thin films were deposited on glass slides by the sol-gel method. The films were doped by the addition of ammonium fluoride to the precursor solution whose optimum concentration was determined. The films were fired in an open atmosphere at 350 °C and after that, exposed to annealing treatments in different atmospheres (N₂, N₂/H₂ mixture and Ar) at the same temperature. The films were characterized by ultraviolet-visible spectroscopy, X‐ray diffraction and scanning electron microscopy. The resistivity was determined by the four probes method and current-voltage measurements in accordance with the standard Van der Pauw configuration. The CdO:F thin films obtained, showed high polycrystalline quality and high transmission in the visible region (≥ 90%), shifting towards the blue region of the absorption edge as the fluorine concentration in the precursor solution was increased from 0 to 30 at.%. The lowest resistivity values were reached for the samples with F content higher or equal to 5% and annealed in either N₂ or a 96/4 N₂/H₂ gas mixture. Our resistivity value reached in the CdO:F layers was 4.5 × 10^{− 4} Ω cm (20 Ω/square).