Superposition Coding with Unequal Error Protection for the Uplink of Overloaded DS-CDMA System

The overloaded CDMA schemes exploited in direct sequence CDMA (DS-CDMA) systems are mainly to accommodate a greater number of users than the available spreading factor N. In this paper, a superposition coding CDMA (SPC-CDMA) with unequal error protection (UEP) is proposed as one of the overloaded CDMA schemes for the next generation mobile communication systems. It exploits the available power control in most base stations to adapt the transmitted power of active users in the uplink channel. In this scheme, the active users are divided into G groups and each group consists of K users. The K users share the same spreading sequence and are distinguished by different received power levels. At the receiver side, the system first performs despreading for group detection followed by multiuser receiver to estimate the K user signals in each group. It is shown through simulations that better performance are achieved compared to the conventional DS-CDMA and existing overloaded collaborative spreading CDMA (CS-CDMA) schemes, in additive white Gaussian noise (AWGN) and fading channels. Hence, the proposed scheme maximizes the system capacity K-fold compared to conventional DS-CDMA system without requiring extra spreading codes, with average signal to noise ratio (SNR) cost of only 1dB and 2 dB over AWGN and fading channels respectively at BER of 10^?3. On the other hand, for the same N, K and power constraints, SPC-CDMA scheme achieves twofold increase in data rate with 0.7 and 4 dB gains over AWGN and fading channels respectively, compared with overloaded CS-CDMA scheme in the same system capacity. In addition, the proposed scheme can also attain different levels of UEP for different users?? requirements by adjusting their fractions of transmitted powers.     

Nanofabrication of gallium nitride photonic crystal light-emitting diodes

We describe a comparison of nanofabrication technologies for the fabrication of 2D photonic crystal structures on GaN/InGaN blue LEDs. Such devices exhibit enhanced brightness and the possibility of controlling the angular emission profile of emitted light. This paper describes three nano lithography techniques for patterning photonic crystal structures on the emitting faces of LEDs: direct-write electron beam lithography, hard stamp nanoimprint lithography and soft-stamp nanoimprint lithography with disposable embossing masters. In each case we describe variations on the technique as well as its advantages and disadvantages. Complete process details have been given for all three techniques. In addition, we show how high performance GaN dry etch techniques, coupled with optical process monitoring can transfer resist patterns into underlying GaN material with high fidelity.     

WSANFlow: An Interface Protocol Between SDN Controller and End Devices for SDN-Oriented WSAN

When dealing with a Wireless Sensor and Actuator Network (WSAN) structure, one of the challenging problems is lack of flexibility in such network operations as establishment, management, and configuration. Software-defined Networking (SDN) is a promising technology for a simpler, more flexible, and less overworked network structure. Integration of SDN as a solution into the existing WSAN structures seems to be a strong candidate of deployment solutions for next generation WSAN systems. In order to get enhanced performance results for WSAN systems, we proposed an interface protocol, referred to as WSANFlow, which is responsible for all the communications between SDN controller (SDNC) and SDN-oriented end devices. The SDNC in this approach has the network intelligence and is capable of handling all the control and management operations related to the network. Thus, advanced communication operations can be managed and efficiently optimized efficiently by the SDN controller and then, subsequently, corresponding instructions can be delivered to end devices using the proposed WSANFlow protocol. In the study, we analyzed the proposed framework performance, in terms of power consumption ratio, throughput, and end to end delay metrics. Then, we compared the results with those of a ZigBee-based counterpart for different workloads such as; light, heavy and heavier load which modelizes a video stream of mild parameters. The results show that not only has the overall performance of the existing WSAN system been enhanced, but also control and management operations have been simplified by the proposed model.     

Interference Mitigation Based on Radio Aware Channel Assignment for Wireless Mesh Networks

An intricate network deployment for high demand users leads to simultaneous transmission in wireless mesh networks. Multiple radios are adapted to individual nodes for improving network performance and Quality of Service (QoS). However, whenever multiple radios are assigned to the same channel, co-located radio interference occurs, which poses a major drawback. This paper proposes a Radio aware Channel Assignment (Ra-CA) mechanism based on a direct graphical model for mitigation of interference in multi-radio multi-channel networks. Initially, the co-located radio interference is identified by classifying non-interfering links for simultaneous transmission in the network. Proposed channel assignment mechanism helps in allocating the minimal number of channels to the network that mitigate co-located radio interference. Performance analysis of the proposed Ra-CA strategy is carried out compared with other existing techniques, like Breadth First Search-Channel Assignment (BFS-CA) and Maximal Independent Set Channel Assignment (MaIS-CA), in multi-radio networks. Simulation results demonstrate that the proposed channel assignment scheme is more efficient compared to the existing ones, in terms of QoS parameters like, packet drop rate, packet delivery ratio, transmission delay and throughput.     

Compact and High Speed Architectures of KASUMI Block Cipher

Wireless Personal Communications - This paper proposes highly compact and high speed hardware architectures of 64-bit KASUMI block cipher for wide range of wireless applications. A novel...     

A Bayer pattern-based fragile watermarking scheme for color image tamper detection and restoration

Multidimensional Systems and Signal Processing - The security of multimedia documents becomes an urgent need, especially with the increasing image falsifications provided by the easy access and use...     

RAPID PYROLYSIS OF EASTERN CANADIAN COALS BY FREE FALL REACTORS

The effect of temperature was investigated on the rapid pyrolysis of Prince, Lingan and No. 26 coals in the temperature range of 525^° to 750^°C using a 600 cm high stainless-steel free fall reactor at atmospheric pressure.

The yields of char, condensibles and gaseous products were determined at 25^°C intervals. Gaseous products were analysed for H₂, CO, CO₂, CH₄ and C₂+.

Volatile product (condensible and gas) yields exceeded the volatile product in the A.S.T.M. methods at and above 700^°C.

Some experiments using Prince coal were repeated at reduced pressure (50 mm mercury) in both the 600 cm height stainless-steel and a 140 cm height quartz reactor in order to find out the effect of pressure and retention time.

The experimental results indicated that the condensable yield was higher at the lower pressure and at the shorter retention time. The effect of retention time was far more pronounced.     

SOLVENT EXTRACTION OF PAKISTANI COALS (ii): EXTRACTION AND CHARACTERIZATION OF METHANOL-BENZENE EXTRACTS

Structural characterization of the solvent extracts from four different Pakistani lignitic coals has been carried out by their proximate, elemental analysis and FT-Infrared and ¹H n.m.r. spectra. The yield of each extracts was greater with 1:1 benzene-methanol mixture in comparison to the total yield obtained by separate extractions with benzene and methanol. The extracts contained significantly less amount of ash and fixed carbon along with an increase in the percentage of volatile matter. The FTIR and ¹H n.m.r. spectra indicated that basically all the extracts contained less condensed aromatic rings in comparison to the coal. The FTIR spectra showed sharp well resolved peaks which have been assigned to various functional groups.

The ¹H n.m.r. spectra were used to obtain average structural parameters for all the extracts. A detailed analysis of the FTIR and n.m.r. spectra of the coal and their extracts provided an important in-sight into the differences between various extracts and also between various coals and their corresponding extracts.