Advanced Method for Single Crystal Casting of Turbine Blades for Gas Turbine Engines and Plants

A method for fabricating single crystal blades that combines the techniques of seed crystals and selection is suggested. The method realizes the advantages of both techniques, i.e., the high structural perfection and the possibility of fabricating single crystals with specified spatial orientation. Metallographic and x-ray diffraction analyses are used to study the processes of nucleation of the single crystal structure of blade castings fabricated from high-temperature nickel alloys by the method of selection and seed crystals. A commercial process for fabricating cast single crystal turbine blades by the new method is suggested.     

International Working Group on Assurance Cases (for Security)

Critical systems are aptly named - from electric power to water and gas to the telephone system and the Internet, they're all critical to some aspect of our daily lives. We're a networked society and as such, it's important to both know whether critical systems are trustworthy and be able to communicate, review, and debate the level of trust achieved in them. In the safety domain, explicit safety cases are increasingly required by law, regulations, and standards. In this article, we outline what a small, international group of experts, spanning various disciplines in safety, security, reliability, and critical infrastructure, been doing with the International Working Group on Assurance Cases (for Security), what we hope to achieve, and where we go next.     

Performance engineering and topological design of metro WDM opticalnetworks using computer simulation

This paper demonstrates the use of computer simulation for topological design and performance engineering of transparent wavelength-division multiplexing metropolitan-area networks. Engineering of these networks involves the study of various transport-layer impairments such as amplifier noise, component ripple, chirp/dispersion, optical crosstalk, waveform distortion due to filter concatenation, fiber nonlinearities, and polarization effects. A computer simulation methodology composed of three main simulation steps is derived and implemented. This methodology obtains performance estimations by applying efficient wavelength-domain simulations on the entire network topology, followed by time-/frequency-domain simulations on selected paths of the network and finally Q-budgeting on an identified worst case path. The above technique provides an efficient tool for topological design and network performance engineering. Accurate simulation models are presented for each of the performance impairments, and the computer simulation methodology is used for the design and engineering of a number of actual metro network architectures     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

干涉条纹图估测基线的方法研究

根据SAR干涉测量原理，提出了利用干涉相干条纹估测基线的方法，并以欧洲空间局资源卫星1号和2号携带的SAR系统在中国新疆伽师试验区获取的串接式（Tan-dem）干涉测量数据为数据源，对提出的方法进行了验证，结果表明，该方法能有效地估测基线，并弥补不能有效获取卫星轨道参数时，对基线进行估测的缺陷，该方法尤其适用于差分干涉测量的研究。     

Use of weibull statistics to quantify property variability in TiAl alloys

Tensile experiments have been performed on specimens of four different investment-cast TiAl-based alloys with variations in casting conditions. The average ductilities obtained in these experiments vary between approximately 0.8 to 2.0 pct plastic strain to failure in tension. By using the three-parameter form of the Weibull relation, with the 0.2 pct offset yield strength as the minimum failure strength, the resulting variability in the data can be quantified and is found to be similar for those alloys with similar microstructural scale (grain size). Large variations in lamellar volume fraction, segregation, and phase distribution have a minor influence on property variability, compared to changes in the scale of the grain structure caused by either variations in cooling rate during casting or the addition of grain refiners.     

Deformation behavior of HCP Ti-Al alloy single crystals

Single crystals of Ti-Al alloys containing 1.4, 2.9, 5, and 6.6 pct Al (by weight) were oriented for 〈a〉 slip on either basal or prism planes or loaded parallel along the c-axis to enforce a nonbasal deformation mode. Most of the tests were conducted in compression and at temperatures between 77 and 1000 K. Trace analysis of prepolished surfaces enabled identification of the twin or slip systems primarily responsible for deformation. Increasing the deformation temperature, Al content, or both, acted to inhibit secondary twin and slip systems, thereby increasing the tendency toward strain accommodation by a single slip system having the highest resolved stress. In the crystals oriented for basal slip, transitions from twinning to multiple slip and, finally, to basal slip occurred with increasing temperature in the lower-Al-content alloys, whereas for Ti-6.6 pct Al, only basal slip was observed at all temperatures tested. A comparison of the critically resolved shear stress (CRSS) values for basal and prism slip as a function of Al content shows that prism slip is favored at room temperature in pure Ti, but the stress to activate these two systems becomes essentially equal in the Ti-6.6 pct Al crystals over a wide range of temperatures. Compression tests on crystals oriented so that the load was applied parallel to the c-axis showed extensive twinning in lower Al concentrations and 〈c+a〉 slip at higher Al concentrations, with a mixture of 〈c+a〉 slip and twinning at intermediate compositions. A few tests also were conducted in tension, with the load applied parallel to the c-axis. In these cases, twinning was observed, and the resolved shear for plastic deformation by twinning was much lower that that for 〈c+a〉 slip observed in compression loading. This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science and Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.     

Constant thrust programming for a multistage rocket flown in vacuum with a given initial/final thrust-to-weight ratio in an arbitrary stage

The burn time and burnout velocity of a multistage rocket flown vertically in vacuum with constant thrust tangential to the flight path and a prescribed initial/final thrust-to-weight ratio in an arbitrary stage have been determined. The present paper also deals with optimal staging under given conditions of flight.