A biochar from casein and its properties

A biochar was prepared by pyrolysis of casein. A helium and mercury porosimeter were used to measure the true and apparent densities of the chars respectively, elemental and IR analysis were used to characterize the chemical composition of char. A SEM was used to observe the char surfaces in order to verify the presence of porosity. The biochar has 9.02% of nitrogen, content of porosity is 20%. The experimental results show that it is possible to prepare chars with relatively high porosity from casein for the further preparation of activated carbon.     

Blind feedforward cyclostationarity-based timing estimation for linear modulations

By exploiting a general cyclostationary (CS) statistics-based framework, this letter develops a rigorous and unified asymptotic (large sample) performance analysis setup for a class of blind feedforward timing epoch estimators for linear modulations transmitted through time nonselective flat-fading channels. Within the proposed CS framework, it is shown that several estimators proposed in the literature can be asymptotically interpreted as maximum likelihood (ML) estimators applied on a (sub)set of the second- (and/or higher) order statistics of the received signal. The asymptotic variance of these ML estimators is established in closed-form expression and compared with the modified Crame/spl acute/r-Rao bound. It is shown that the timing estimator proposed by Oerder and Meyr achieves asymptotically the best performance in the class of estimators which exploit all the second-order statistics of the received signal, and its performance is insensitive to oversampling rates P as long as P/spl ges/3. Further, an asymptotically best consistent estimator, which achieves the lowest asymptotic variance among all the possible estimators that can be derived by exploiting jointly the second- and fourth-order statistics of the received signal, is also proposed.     

Reliability studies of MOCVD TiSiN and EnCoRe Ta(N)/Ta

Passivated single damascene copper SiO₂ damascene lines were evaluated in combination with TiSiN and Ta(N)/Ta diffusion barriers. Leakage current, breakdown and time-dependent dielectric breakdown properties were investigated on a wafer level basis for temperatures ranging between room temperature and 150 °C. It is found that the leakage performance of the wafers with a TiSiN barrier is better at room temperature, but at 150 °C the performance levels out with Ta(N)/Ta. Time-dependent dielectric breakdown measurements at 150 °C show that the lifetime of the interconnect is higher with the selected Ta(N)/Ta barrier than for TiSiN.     

Platinum Binuclear Complexes as Phosphorescent Dopants for Monochromatic and White Organic Light‐Emitting Diodes

Efficient blue‐, green‐, and red‐light‐emitting organic diodes are fabricated using binuclear platinum complexes as phosphorescent dopants. The series of complexes used here have pyrazolate bridging ligands and the general formula C^∧NPt(μ‐pz)₂PtC^∧N (where C^∧N = 2‐(4′,6′‐difluorophenyl)pyridinato‐N,C^2′, pz = pyrazole ( 1 ), 3‐methyl‐5‐tert‐butylpyrazole ( 2 ), and 3,5‐bis(tert‐butyl)pyrazole ( 3 )). The Pt–Pt distance in the complexes, which decreases in the order 1 > 2 > 3 , solely determines the electroluminescence color of the organic light‐emitting diodes (OLEDs). Blue OLEDs fabricated using 8 % 1 doped into a 3,5‐bis(N‐carbazolyl)benzene (mCP) host have a quantum efficiency of 4.3 % at 120 Cd m^–2, a brightness of 3900 Cd m^–2 at 12 V, and Commission Internationale de L'Eclairage (CIE) coordinates of (0.11, 0.24). Green and red OLEDs fabricated with 2 and 3 , respectively, also give high quantum efficiencies (～ 6.7 %), with CIE coordinates of (0.31, 0.63) and (0.59, 0.46), respectively. The current‐density–voltage characteristics of devices made using dopants 2 and 3 indicate that hole trapping is enhanced by short Pt–Pt distances (< 3.1 Å). Blue electrophosphorescence is achieved by taking advantage of the binuclear molecular geometry in order to suppress dopant intermolecular interactions. No evidence of low‐energy emission from aggregate states is observed in OLEDs made with 50 % 1 doped into mCP. OLEDs made using 100 % 1 as an emissive layer display red luminescence, which is believed to originate from distorted complexes with compressed Pt–Pt separations located in defect sites within the neat film. White OLEDs are fabricated using 1 and 3 in three different device architectures, either with one or two dopants in dual emissive layers or both dopants in a single emissive layer. All the white OLEDs have high quantum efficiency (～ 5 %) and brightness (～ 600 Cd m^–2 at 10 V).     

Intelligent process analytics for CRM

Many organisations use decision models in their processes such as tables or trees to provide decision support to their operational divisions. For example, in fault management, customer contact centre operators usually use a decision model in the form of prescribed interviews. Based on the answers given by customers, the operator navigates through the decision model to reach an assessment of the problem. In order to achieve customer satisfaction and operational excellence, it is very important to constantly monitor the performance of a decision model not only on an overall level, but also on the level of individual decisions. In this paper we present a configurable business process analytics tool, known as the intelligent Universal Service Management System, that constantly monitors decision data and is capable of optimising the decisions based on high-level business objectives. We explain the various features of the software and show how it can be used to optimise decision processes. We also show how we can easily provide a customised version to monitor the performance of provision processes.     

Fault detection for control of wastewater treatment plants.

Interest in real-time model-based control is increasing as more and more facilities are being asked to meet stricter effluent requirements while at the same time minimizing costs. It has been identified that biological process models and automated process control technologies are being used at wastewater treatments plants throughout the world and that great potential for optimising biotreatment may exist with the integration of these two technology areas. According to our experience, wastewater treatment plants are indeed looking for ways to successfully integrate their modelling knowledge into their process control structure; however, there are practical aspects of this integration that must be addressed if the benefits of this integration are to be realised. This paper discusses the practical aspects of monitoring, filtering and analysing real sensor data with an aim to produce a reliable real-time data stream that might be used within a model-based control structure. Several real case study examples are briefly discussed in this paper.     

Comparison of total and faecal coliforms as faecal indicator in eutrophicated surface water.

The aim of this study was to evaluate the use of total coliforms (TC) and faecal coliforms (FC) using a membrane filtration method for precise monitoring of faecal pollution in Korean surface water. The samples were collected in Korea from both main rivers and their tributaries. Presumptive TC * FC were enumerated. The ratios of presumptive FC to TC were not constant, but varied widely, and TC were difficult to enumerate because of overgrowth by background colonies. For FC this was not the case. Seven hundred and three purified strains of presumptive TC * FC and their background colonies were biotyped using API 20E. Among 272 presumptive TC, non-faecal related species, Aeromonas hydrophila dominated (34.6%) and E. coli accounted for only 5.1%. In contrast, E. coli made up 89% of the 209 presumptive FC. Furthermore, of 164 background colonies on Endo Agar LES, 54.9% was A. hydrophila, while background colonies on m-FC Agar were few (58 strains), and despite their atypical colony appearance, most of them were biotyped as enteric bacteria. These results reveal that the detection of FC rather than TC using m-FC Agar is more appropriate for faecal pollution monitoring in eutrophicated surface water located in a temperate region.     

Recovery of gold cyanide using inherently conducting polymers

Removal of gold from basic solutions containing [Au(CN)₂]^? has been demonstrated using the inherently conducting polymer polypyrrole. Polymers containing sulfonated aromatic dopants have been found to display a significant ability to remove gold from such solutions. Experiments performed in solutions containing both gold and copper cyanide complexes indicate that the recovery process is not highly selective. However, the polypyrroles used display significantly faster rates of gold recovery than activated carbon. © 2003 Society of Chemical Industry     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Evaluation and optimization of package processing and design through solder joint profile prediction

Solder joints are generated using a variety of methods to provide both mechanical and electrical connection for applications such as flip-chip, wafer level packaging, fine pitch, ball-grid array, and chip scale packages. Solder joint shape prediction has been incorporated as a key tool to aid in process development, wafer level and package level design and development, assembly, and reliability enhancement. This work demonstrates the application of an analytical model and the Surface Evolver software in analyzing a variety of solder processing methods and package types. Bump and joint shape prediction was conducted for the design of wafer level bumping, flip-chip assembly, and wafer level packaging. The results from the prediction methodologies are validated with experimentally measured geometries at each level of design.