Effects of insufficient air injection on methanogenic Archaea in landfill bioreactor

In this study, methanogenic Archaea diversity in an aerated landfill bioreactor filled with co-disposed incineration bottom ashes and shredded incombustible wastes was monitored and analyzed as a function of time using molecular techniques. Besides, the effects of insufficient air injection on the bioreactor performance and methanogenic diversity were evaluated thoroughly. Results indicated that rapid bio-stabilization of solid waste are possible with aerated landfill bioreactor at various oxygen and oxidation reduction potential levels. Slot-blot hybridization results of leachate samples collected from aerated landfill bioreactor showed that archaeal and bacterial activities increased as stabilization accelerated and bacterial populations constituted almost 95% of all microorganisms. The results of slot-blot hybridization and phylogenetic analysis based on 16S rRNA gene revealed that Methanobacteriales and Methanomicrobiales were dominant species at the beginning while substituted by Methanosarcina-related methanogens close to the end of the operation of bioreactor.     

Effect of γ-irradiation dose for the oxygen diffusion into polymers

Electron spin resonance (ESR) spectroscopy has been used for the measurement of the diffusion coefficient of oxygen into polymeric spheres. It has been shown that there is an inverse dependency between the irradiation dose and the oxygen diffusion coefficient (D). The free-radical concentration (R_o) produced in the polymer depends on the dose of the γ rays. In this study, we tried to find a relationship between the oxygen diffusion coefficient and the free-radical concentration produced in the polymer during the irradiation. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 1291–1294, 1997     

Synthesis and characterization of phosphorus-containing methacrylate-based difunctional crosslinkers and their use in UV-curable resin systems

Two new phosphorus-containing methacrylate-based difunctional crosslinking agents [bis(4-(2-methacryloyloxy)ethyl carboxyl)phenyl phosphine oxide (BEPPPO) and bis(4-(2-methacryloyloxy)ethylcarbonylaminophenyl)phenyl phosphine oxide (BUPPPO)], which can be good candidates for UV-curable coating applications, were synthesized by reacting either a phosphorus-containing diisocyanate [bis(4-isocyanatophenyl)phenyl phosphine oxide] or a phosphorus-containing diacid chloride [bis(4-chloroformylphenyl)phenyl phosphine oxide] with hydroxyethyl methacrylate. The structures of the monomers thus obtained were characterized by FTIR, mass, and ¹H-NMR spectroscopies. The contents of the new crosslinking agents in the UV-cured polymeric films were varied between 10 and 30% by weight. Mechanical, physical, and thermal characterizations of the UV-cured films were investigated. An increase in crosslinking agent content caused an increse in mechanical properties. Films containing BUPPPO had higher tensile strength values compared to the films containing BEPPPO. Thermogravimetric analysis of phosphorus-containing crosslinking agents revealed that incorporating phosphorus into the structure resulted in a high char yield up to 24.5% at 600°C. Water absorption values of UV-cured films were also affected by the amount and type of crosslinking agent. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2575–2585, 1999     

Development of MTV Compositions as Igniter for HTPB/AP Based Composite Propellants

MTV compositions were prepared by keeping the magnesium/Teflon ratio constant and increasing the Viton content of the mixture up to 14% by an increment of 2% to investigate the effect of binder content on the heat of explosion, which is found to increase with the increasing Viton percentage as the magnesium content concomitantly goes down toward the stoichiometric value. In the second part of the study, fuel-rich MTV compositions were prepared by changing the magnesium content and keeping the Viton fraction constant at a specific value to investigate the effect of magnesium content on the heat of explosion and combustion characteristics. The observed general trend is that the heat of explosion of MTV compositions decreases as the magnesium content increases. All the MTV compositions were tested in a closed vessel to measure the maximum pressure achieved and the rate of reaching this pressure. The ignition performance of three selected MTV compositions was examined in 2.75 inch rocket motor by using the same charge of igniter and the same HTPB/AP composite propellant of the equal amount in each test. Two of them have excellent ignition performance and, therefore, can be used as igniter for the HTPB/AP based composite rocket propellants.     

Surface Treatment of S355JR Carbon Steel Surfaces with ZrB<Subscript>2</Subscript> Nanocrystals by CO<Subscript>2</Subscript> Laser

To improve mechanical properties of S2355JR carbon steel, pre-synthesized ZrB₂ nanocrystals were used to coat the metal surface by laser cladding using 2000 W CO₂ laser. ZrB₂ nanocrystals were synthesized by mechanochemical process. The effect of laser power on the coating layers was examined for optimizing the most effective coating conditions. Microstructural studies were carried out using optical microscope, scanning electron microscope and X-ray diffraction to analyze phase structures of the coated layers. Mechanical characteristics of the laser coated layers were evaluated by studying microhardness, wear and scratch resistance properties. Maximum hardness of the coated layers was observed while cladding with 75 and 125 W laser powers, when other processing parameters and conditions were kept at optimum levels. EDS analysis of these laser cladded layers indicated the formation of complex boro-nitrides, nitrides and carbides of Zr and Fe that contributed to vast increase in hardness of the laser-clad coating on S2355JR steel. Depending upon the laser powers used, the thickness of the coated layers was found to be in the range of 15–37 µm. The wear and micro-scratch tests results revealed significant improvement in wear properties.     

Effect of Ball Burnishing Treatment on the Fatigue Behavior of 316L Stainless Steel Operating Under Anodic and Cathodic Polarization Potentials

Corrosion fatigue (CF) behavior of AISI 316L was investigated in a 3 pct NaCl aqueous solution at an R = ? 1 stress ratio and a frequency of 60?Hz at room temperature. The test scale specimen was 7 cm². The passive (0 mV_Ref), pitting (120?mV_Ref), and cathodic (? 1400?mV_Ref) polarization potentials were statically applied and recorded during CF tests until the samples were broken. The shaft material surface was treated with a ball burnishing (BB) process. By the results, the fatigue behavior of AISI 316L was affected by polarization potential and surface treatment. Under 0?mV potential charged tests for 5?×?10⁵ cycles, BB treatment raised the CF strength of the shaft material from about 448 to 702?MPa with a percent 57 increase. Fractographic observations revealed that corrosion pits occurred during the experiments where anodic potential was applied and that transgranular surface fractures occurred in all cases.