Photosensitivity in low-loss perfluoropolymer (CYTOP) fibrematerial

Photosensitivity in a perfluoropolymer (CYTOP) optical fibre is investigated. Significant diffraction has been observed from transmission gratings made from the fibre. A maximum diffraction efficiency of 1.6% has been achieved, corresponding to an index change ≃3×10^-4. The study demonstrates for the first time the existence of significant photosensitivity and the feasibility of writing a Bragg grating in a CYTOP fibre     

基于千兆以太网的高速图像数据传输系统实现

针对高速图像数据传输的实际需求设计了一种基于千兆以太网的大容量数据高速传输设计方案。该方案根据实际需求充分利用FPGA可重构性的优势,实现了以UDP协议为基础的自定义全双工MAC核,其优化的命令接收模式在接收端绕过了TCP/IP协议降低了FPGA端协议解析的复杂度与硬件开销;其流量可控并带有重传机制的数据上传模式可以与不同配置、不同工况的上位机稳定可靠高效率传输。实际最高传输速率达到稳定的49MB/s,性能优越。     

全光通信网技术

本文对全光网的概念和关键技术做了简要说明，并介绍了具有代表性的全光网络，最后对各个网络的技术进行了比较，并同了全光网发展的一些主要障碍。     

热成像温差分辨率与微分光谱匹配因数的关系

由近距离低温面目标热成像系统的信号方程和噪声等效温差ＮＥＴＤ的定义，导出了ＮＥＴＤｏｃ１／Ｍ，并由此得到ＭＲＴＤｏｃ１／Ｍ，ＭＤＴＤｏｃ１／Ｍ，从而证明了热成像系统的温差分辨率；ＮＥＴＤ、ＭＲＴＤ、ＭＤＴＤ均要求微发光谱匹配因数Ｍ要大，这为选用光谱区配因数Ｍ和Ｍ作为热成像系统的综合评价参数奠定了理论基础。     

Hg_（1－x）Cd_xTe的扫描光致发光研究

用傅里叶变换红外扫描光致发光方法研究了Ｈｇ１－ｘＣｄｘＴｅ体单晶样品，该方法可直接得到ＨｇＣｄＴｅ晶片组分的二维平面分布，并可得到辐射复合在复合机制中所占比重的平面分布，以及晶体中非平衡载流子寿命的分布     

An Architecture of Scalable ATM Switching System and Its Call Processing Capacity Estimation

In this paper, we define the general requirements of ATM switching systems such as scalability, distributed fashion, and modularity. Also we propose a practical implementation of a scalable ATM switching system whose capacity can be easily expanded. Firstly, the architecture of the system is discussed with an emphasis on system scalability, modularity of subsystems and the simple control network of the design requirements. Secondly, we suggest the three types of distributed call/connection control schemes that are suitable for our switching system. We also estimate their call processing capacity on the average and make a comparison of them under the various system architectures. Since our scalable switching system can be constructed to perform the call processing functions on the various levels of the system capacity, it has much adaptability at the various evolution phases or regions of the network environment.     

不同类型断层控制油气垂向富集的差异——以渤海湾盆地歧口凹陷歧南斜坡区为例

渤海湾盆地历经多期构造变动，断层圈闭发育普遍。断层作为断层圈闭的边界条件，在油气成藏过程中起着至关重要的作用。以断层圈闭较发育的歧南斜坡区为例分析了同向断层和反向断层控制油气垂向富集的差异，基于三维地震资料，从断层形成过程和断层圈闭分布出发，剖析了断层遮挡圈闭的成因及分布规律。结合油水分布规律，基于油藏解剖并应用储层定量荧光技术明确了不同类型断层控藏的差异及其形成机理。研究表明：①断层分段生长作用和断层上盘与下盘的差异活动是同向断层控制下断层遮挡圈闭形成的主要原因，斜坡区反向断层控制形成的断层圈闭则是断块掀斜翘倾作用所致；②同向断层圈闭发育在断层上盘分段点位置，只有当同向断层进入"硬连接"阶段方可形成断层圈闭，反向断层圈闭形成在断层下盘，在反向断层活动初期便可形成；③同向断层既可以控制油气在多套含油气系统中聚集成藏，也可在一套含油气系统中富集，而反向断层往往控制油气在一套含油气系统中富集；④不同类型断层控制油气垂向聚集的差异与圈闭发育位置以及断-盖配置有关。采用泥岩涂抹系数对沙河街组一段中部盖层控制的含油气系统的垂向调整进行定量评价，泥岩涂抹系数低于3.5时油气保存，泥岩涂抹系数高于3.5时油气垂向渗漏。     

A scalar finite-difference time-domain approach to guided-wave optics

A finite-difference time-domain approach that solves the scalar wave equations is proposed and validated. The propagation, reflection, scattering, and radiation of electromagnetic waves in weakly guiding optical devices are described explicitly in the time domain. The method is applied to the simulation of guided-wave devices such as directional couplers and distributed feedback reflectors. A comparison to known analytical solutions shows good agreement.<>     

A new calibration algorithm of wide-band polarimetric measurementsystem

The principle and experimental results of a new self-consistent calibration algorithm for a wideband polarimetric scattering measurement system are presented. The calibration targets include a flat plate, a dihedral corner reflector, and a rotated dihedral corner reflector. The rotation angle of the third calibrator can be derived in the calibration process and used to verify the calibration performance. Experimental results show that the calculated rotation angle of the third calibrator over the operation bandwidth is in good agreement with its actual angle, hence it provides a self-consistent parameter of the calibration algorithm. Based on the signal-to-noise consideration, an optimal rotation angle for a dihedral corner reflector is found to be 22.5°. This calibration technique is also useful in characterizing the frequency and polarization responses of dual-polarization antennas     

刀具参数对加工表面粗糙度影响的研究

通过车削加工试验和数据测量,研究了刀具参数及刀具磨损量对加工表面粗糙度的影响。应用Matlab计算得出刀具参数变化和刀具磨损量对加工表面粗糙度的定量关系,为加工时选用刀具参数及控制刀具磨损量提供理论依据。