Effect of attapulgite added in plating bath on the properties of Ni/TiC nano-composite coatings

Pure copper plates were coated by Ni-TiC dipulse current plating method. The effects of adding different concentration(ranging from 0.5 g/L to 3.0 g/L) of attapulgite nano particles to the plating bath on the surface morphology, wear resistance, and oxidation resistance of Ni/TiC/Attapulgite nano-composite coatings were investigated. The experimental results show that the composite coating is flat and compact with adding 3.0 g/L in the bath, and the coating preferred orientation is changed from the planes (111) to (200). The coefficient of the composite coatings decreases from 0.68 to 0.18 with increasing content of attapulgite in the bath, a mixed mode of adhesive-abrasive wear occurs for all coatings, and the wear mechanism shows a transition from adhesive-abrasive to predominantly abrasive wear mechanism when the concentration of attapulgite is beyond 1.5 g/L in electrolyte. The oxidation resistance of composite coatings is the best prepared when adding attapulgite particles at 0.5 g/L in the bath, the oxide mainly consists of a NiO phase by X-ray analysis.     

Effect of fiber volume fraction on longitudinal tensile properties of SiC<Subscript>f</Subscript>/Ti-6Al-4V composites

The longitudinal tensile properties of SiC_f/Ti-6Al-4V composites with different fiber volume fractions were simulated by the Monte Carlo 2-D finite element model. The random distribution of fiber strength was expressed by the two-parameter Weibull function. Meanwhile, contact elements and birth-death elements were used to describe the interfacial sliding process after debonding and fiber breakage (or matrix cracking) respectively, which was realized by subroutine complied in ANSYS-APDL (ANSYS Parametric Design Language). The experimental results show that the yield stress and ultimate tensile strength of SiC_f/Ti-6Al-4V composites increase with increasing fiber volume fraction, while the corresponding strain of them is just on the contrary. In addition, almost the same failure mode is obtained in SiC_f/Ti-6Al-4V composites with various fiber volume fractions when the interfacial shear strength is fixed. Finally, the tensile strength predicted by finite element analysis is compared with that predicted by Global load-sharing model, Local load-sharing model and conventional rule of mixtures, thus drawing the conclusion that Local load-sharing model is very perfect for the prediction of the ultimate tensile strength.     

Effect of deposition time on microstructures and growth behavior of ZrC coatings prepared by low pressure chemical vapor deposition with the Br<Subscript>2</Subscript>-Zr-C<Subscript>3</Subscript>H<Subscript>6</Subscript>-H<Subscript>2</Subscript>-Ar System

ZrC coatings were deposited on graphite substrates by low pressure chemical vapor deposition (LPCVD) with the Br₂-Zr-C₃H₆-H₂-Ar system. The effects of deposition time on the microstructures and growth behavior of ZrC coatings were investigated. ZrC coating grew in an island-layer mode. The formation of coating was dominated by the nucleation of ZrC in the initial 20 minutes, and the rapid nucleation generated a fine-grained structure of ZrC coating. When the deposition time was over 30 min, the growth of coating was dominated by that of crystals, giving a column-arranged structure. Energy dispersive X-ray spectroscopy showed that the molar ratio of carbon to zirconium was near 1:1 in ZrC coating, and X-ray photoelectron spectroscopy showed that ZrC was the main phase in coatings, accompanied by about 2.5mol% ZrO₂ minor phase.     

Synthesis and characterization of triangular-pyramidal bismuth oxide via a one-step chemical precipitation route

Triangular-pyramidal ω-Bi_2O_3 is successfully synthesized via a one-step wet-chemical method.XRD,SEM,and UV-vis have been employed to characterize the as-prepared samples.Structural characterization by XRD confirms the formation of triclinic ω-Bi_2O_3 with high purity.The well-defined flowerlike Bi_2O_3 structures consisted of many triangular-pyramids are formed.Preparative parameters,such as concentration of PEG 6000,have great effects on the morphology and the particle size.The obvious absorption edge for ω-Bi_2O_3 powder is located at about 493 nm,which corresponds to the optical band gap energy of2.73 eV.     

Characteristics of cationic Red X-GRL adsorption by diatomite tailings

As secondary mineral resources, diatomite tailings(DT) got from the Linjiang region of China were prepared and characterized by SEM, XRF and XRD. Mono-factor experiments were carried out to investigate the effects of the operation factor, including contact time, adsorbent concentration, initial p H value of the dye solutions, adsorption temperature and initial concentration of cationic Red X-GRL(X-GRL) on the adsorption of X-GRL. The adsorption kinetics, isotherms, thermodynamics and mechanisms for X-GRL were also studied. It was efficient for DT to adsorb X-GRL from aqueous solutions, and it was even discovered to have higher adsorptivity for X-GRL than diatomite concentrate(DC) in our previous test. The adsorption processes fit very well with the pseudo-second-order model and the Langmuir isotherm equation. In addition, various thermodynamic parameters, such as standard Gibbs free energy(ΔG°), standard enthalpy(ΔH°) and standard entropy(ΔS°) have been calculated. From thermodynamic studies, it was seen that the adsorption was spontaneous and endothermic. The main driving forces of the physical adsorption on DT are electrostatic attraction. The reason why DT showed higher adsorptivity for X-GRL than DC was that there were more clay mineral particles within, which has a remarkable ability of dye adsorption due to its high surface area. DT as a cheap absorbent for X-GRL removal would replace or partially replace the activated carbon.     

Effects of LiAl-layered double hydroxides on early hydration of calcium sulphoaluminate cement paste

As a 3D micro-nano material, layered double hydroxides have been widely used in many fields, especially for reinforced composite materials. In this paper, LiAl-LDHs was obtained by a hydrothermal method. In order to investigate the effects of LiAl-LDHs on the early hydration of calcium sulphoaluminate (CSA) cement paste, compressive strength, setting time and hydration heat were tested while X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scaning electron microscopy (SEM) and differential scanning calorimetry (DSC) analysis were employed. The results indicated that LiAl-LDHs could significantly improve the early compressive strength and shorten the setting time of calcium sulphoaluminate cement paste with 3wt% concentration. Besides, the hydration exothermic rate within 5 h was accelerated with increasing LiAl-LDHs content. Moreover, the addition of LiAl-LDHs did not result in the formation of a new phase, but increased the quantity of hydration products providing higher compressive strength, shorter setting time and denser microstructure.     

Preparation and performance research of cement-based grouting materials with high early strength and expansion

Main performance of the cement grouting materials made up by Portland cement(PC) and sulphoaluminate cement(SAC) was investigated in this program, a kind of expanding agent(EA) which was mainly constituted by metakaolin and alunite was utilized for the compensation of the shrinkage, the hydration products and micro structure of the grouting materials were researched by X-ray diffraction(XRD) and scanning electron microscopy (SEM). The results showed that a high expansion rate of the grouting materials could be reached as the expanding agent mixed in 6% of PC mass; the addition of SAC in the S2(PC:SAC:EA=34:6:2.25) brought a further improvement of the expansion rate of the grouting materials, the analysis of XRD and SEM showed that due to the reaction of expanding agent and SAC in the grouting materials, more ettringite crystal was generated, which resulted in a higher early strength, the addition of SAC played an expansion and strength reinforcement role in the grouting materials.     

Inter-comparative study of quantitative methods of industrial clinker

Impurities from the raw materials, the grinding and the homogenization of the raw materials, the kiln instability and the complexity of the cooling step, all these factors make it difficult to obtain a perfect evaluation of the mineralogical composition of Portland clinker. We studied the limitations of the most commonly used quantitative methods and recommend some procedures to obtain reliable and reproducible results of quantitative analyses. Different clinker samples (provided by the Bizerte Cement Company (Tunisia)) were subjected to an elemental analysis by X-ray fluorescence and the mineralogical composition was determined by the Bogue calculation and by X-ray powder diffraction combined with the Rietveld method (Different softwares were used: XPert High Score Plus version 2.0 and TOPAS version 4.2). We then compared the results obtained by the Rietveld method and the Bogue calculation to the specific peak areas of each phase. The content of each phase, determined by the Rietveld method, varied proportionally to the change in peak area; a significant difference in these results was found by using the elementary Bogue calculation.     

Synthesis of HTPB based PU-PS IPN membrane for pervaporation recovery of butanol

Hydroxyl terminated polybutadiene(HTPB) based polyurethane(PU)-polystyrene(PS) interpenetrating polymer network(IPN) was prepared and characterized by FTIR, TGA, WCA, swelling experiments, and SEM. The IPN was used for pervaporation(PV) recovery of butanol. Both the permeation flux and separation factor increased with feed temperature, and both water and butanol fluxes increased with feed concentration while no obvious effect of concentration on separation factor was found. Through the formation of IPN structure, the total flux of HTPB based PU increased greatly with the decrease of separation factor. At the feed temperature of 60 °C, the IPN membrane obtained a total flux of 613.3 g/m~2 h with a separation factor of 6.15.     

A new way of strengthening and toughening for carbon fiber reinforced polyphenylene sulfide (CF/PPS) composites via matrix modification

The effect of pressure-induced flow(PIF) processing on the mechanical properties of noncontinuous carbon fiber(CF) reinforced polyphenylene sulfide(PPS) composites was investigated. A series of CF/PPS composites under different processing conditions were prepared through PIF-processing. SEM observations showed that the interfaces adhesion between CFs and PPS became stronger and ductile fracture mainly occurred in PPS matrix. This brought to a great increase of both strength and toughness by about 2 folds, when the composites were processed at 240 ℃ and under 263 MPa. The results in differential scanning calorimetry(DSC) and X-ray diffraction(XRD) measurements indicated more regular crystalline structures and orientation of lamellae formed during PIF-processing.