Spectral shape tunable band-rejection filter using a long-period fiber grating with divided coil heaters

We have developed a new type of tunable band rejection filter, which provides high spectral-shaping flexibility in a wide tuning range. The filter consists of a long-period fiber grating (LPFG) with divided coil heaters. Each of the divided coil heaters is controlled individually to adjust a temperature distribution along the LPFG and to modify the spectral shape of the LPFG filter. The tunable band rejection filter is demonstrated to function properly when applied as an erbium-doped fiber amplifier gain-flattening filter.     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

龙滩水电站地下厂房进水口高边坡加固支护设计

龙滩水电站地下厂房进水口高边坡开挖坡高达435m，坡面面积达27万m^2，为典型的反倾向层状结构岩质高边坡。为了确保进水口坝段的稳定，必须保持边坡岩体有足够的稳定性，通过采取边坡轮廓设计，防渗、排水设计，加固支护设计及施工控制等一系列措施，确保边坡稳定。文章简要论述了边坡设计的原则、标准、高边坡轮廓设计、防渗排水系统、加固支护措施、施工控制等情况。     

渤海绥中油田J3井疏水缔合聚合物驱数值模拟研究

为了进一步提高渤海油田J3井区缔合聚合物驱的技术经济效果,在渤海油田室内配方和先导性矿场试验研究基础上,利用化学驱油藏数值模拟软件FAPMS,分析和研究了高浓度缔合聚合物前置段塞、主段塞的大小和浓度以及段塞组合方式对驱油效果的影响,优化设计了渤海绥中油田J3井区块矿场试验的最佳注入程序及段塞大小。结果表明,通过对不同浓度的疏水缔合聚合物注入的前置段塞及主段塞和梯度式后续段塞的优化后,原油采收率比未优化时提高了约10个百分点。研究表明,渤海油田应该高度重视聚合物驱的注入方式和段塞优化设计,进一步提高聚合物的技术经济效果。     

基于USB总线的虚拟频谱分析仪设计

文章详细介绍了基于USB总线的虚拟频谱分析仪的设计过程。该仪器使用嵌入式混合处理器MC56F8323来实现动态信号的实时采集、频谱分析和数字滤波等功能。处理结果由USB2．0接口芯片CY7C68013上传至PC机．以完成数据显示、存储、绘制图形等功能。其中，CY7C68013工作于Slave FIFO模式，以实现与MC56F8323间的数据传输。该系统可同时对两路动态信号进行实时谱分析，每路采样频率高选500kHz。     

砾岩储层精细描述中标准测井资料的应用

克拉玛依油田七区的标准测井资料是指使用标准电极系视电阻率测井、自然电位测井和井径测井,以相同的1:500深度比例尺及相同的横向比例进行测井作业所取得的资料.这种资料本来并不具备定量解释储层孔隙度和含油饱和度的能力,但这种资料占该区测井资料总量的比率高达34%.利用标准电极系视电阻率资料和岩心分析资料建立了视电阻率-岩性图版,利用自然电位减小系数α和岩心孔隙度分析资料φ建立了α-φ图版,根据综合测井资料求出标准测井视电阻率校正系数,进而确定了饱和度计算方程的参数.与相应的综合测井资料计算结果相对比,用该方法得到的孔隙度平均绝对误差及相对误差分别为1.85%和11.88%;含油饱和度平均绝对误差及相对误差分别为9.08%和24.75%.将该方法有选择地应用到该区砾岩储层精细描述研究中,弥补了缺乏综合测井资料无法进行测井储层评价及参数研究的缺陷.     

嵌人式与独立存储器设计上的差异分析和研究

进入21世纪,随着集成电路的发展,SoC(System on Chip)片上系统应运而生。而作为SoC重要组成部分的嵌入式存储器,在SoC中所占的比重正逐步增加,并起着越来越重要的作用,那么嵌入式存储器与独立的存储器芯片在设计上存在着哪些差异?对此本文将以NOR型闪存为例在制造工艺的选取、衍生产品的设计、功耗与噪声、后端功能仿真、测试与修复等方面进行分析和研究。     

用DSP实现多目标实时跟踪

介绍了在 TMS3 2 0 C62 0 3上实现 4个目标的快速跟踪技术。为了提高实时性和精确度 ,采用线性汇编优化实现。1个 3 2 0× 160主窗口的 DSP平均处理时间为 2 m s,3个 60× 60副窗口的 DSP平均处理时间各为 0 .4ms,实现了复杂背景下低对比度目标的快速跟踪。实验结果证明跟踪效果良好 ,解决了以前窗口开不大、跟踪速度慢的问题     

农村通信如何"突围"

农村通信作为农村地区信息化的基础，对于全面建设小康具有特殊的重要地位。介绍了我国农村通信的发展现状，分析了农村通信发展的困难压其原因，最后对农村压边远、欠发达地区通信的均衡震展提出了一些建议。     

Alumina-supported catalysts for propane oxidative dehydrogenation from mixed VXM(6−X)O19 (M=W, Mo) hexametalate precursors

γ-Al₂O₃ supported vanadium oxides were modified by tungsten and molybdenum oxides in order to improve dispersion and selectivity towards olefins in propane oxidative dehydrogenation (ODH). Both vanadium–tungsten and vanadium–molybdenum catalysts were obtained by adsorption of mixed isopolyanions (VW₅O₁₉⁵⁻, V₂W₄O₁₉⁴⁻, VMo₅O₁₉⁵⁻ and V₂Mo₄O₁₉⁴⁻) from aqueous solutions. The isopolyanion solutions were characterized by UV-Vis and ⁵¹V NMR spectroscopy. Vanadium, vanadium–tungsten and vanadium–molybdenum precursors and catalysts were also characterized by UV-Vis (diffuse reflectance) and solid state ⁵¹V NMR spectroscopy. An improved selectivity to propene in the presence of tungsten and molybdenum in VO_x/γ-Al₂O₃ was observed and attributed to dilution of vanadium by tungsten or molybdenum oxides on the γ-Al₂O₃ surface.