An isolated ZVS/ZCS flyback converter using the leakage inductanceof the coupled inductor

This paper describes a simple and effective way to modify an existing hard-switched flyback power converter into a circuit with zero-voltage switching (ZVS) and zero-current switching (ZCS). The key improvement is to turn the unattractive features of the coupled inductor leakage inductance and snubber capacitor into attractive ones. The coupled inductor leakage inductance and snubber are used to form a quasi-resonant circuit to facilitate ZVS/ZCS of all power devices. The operating principles of the power converter and experimental results are presented     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

Anomalous variations of OFF-State leakage current in poly-Si TFTunder static stress

Studies the anomalous variations of the OFF-state leakage current (I_OFF) in n-channel poly-Si thin-film transistors (TFTs) under static stress. The dominant mechanisms for the anomalous I_OFF can be attributed to (1) I_OFF increases due to channel hot electrons trapping at the gate oxide/channel interface and silicon grain boundaries and (2) I_OFF decreases due to hot holes accumulated/trapped near the channel/bottom oxide interface near the source region. Under the stress of high drain bias, serious impact ionization effect will occur to generate hot electrons and hot holes near the drain region. Some of holes will be injected into the gate oxide due to the vertical field (~(V_Gstress V_Dstress)/T _OX) near the drain and the others will be migrated from drain to source along the channel due to lateral electric field (~V_Dstress/L_CH)     

A Survey on the Numerics and Computations for the Landau-Lifshitz Equation of Micromagnetism

The Landau-Lifshitz (LL)equation of micromagnetism governs rich variety of the evolution of magnetization patterns in ferromagnetic media. This is due to the complexity of physical quantities appearing in the LL equation. This complexity causes also an interesting mathematical properties of the LL equation: nonlocal character for some quantities,nonconvex side-constraints, strongly nonlinear terms. These effects influence also the numerical approximations. In this work, recent developments on the approximation of weak solutions, together with the overview of well-known methods for strong solutions,are addressed. Author is supported by the Fund for Scientific Research - Flanders FWO (Belgium).     

Synthesis and comparative molecular field analysis (CoMFA) of antitumor 3-arylisoquinoline derivatives

In this study a series of 3-arylisoquinoline derivatives were synthesized and cytotoxicity against human melanoma tumor cell evaluated, and a three dimensional quantitative structure-activity relationship was investigated using the comparative molecular field analysis (CoMFA). The results suggested that the electrostatic, steric and hydrophobic factors of 3-arylisoquinolines were strongly correlated with the antitumor activity. Considerable predictive ability (cross-validated r2 as high as 0.721) was obtained through CoMFA.     

Intelligent copyright protection system using a matching video retrieval algorithm

Many video service sites headed by YouTube know what content requires copyright protection. However, they lack a copyright protection system that automatically distinguishes whether uploaded videos contain legal or illegal content. Existing protection techniques use content-based retrieval methods that compare the features of video. However, if the video encoding has changed in resolution, bit-rate or codec, these techniques do not perform well. Thus, this paper proposes a novel video matching algorithm even if the type of encoding has changed. We also suggest an intelligent copyright protection system using the proposed algorithm. This can serve to automatically prevent the uploading of illegal content. The proposed method has represented the accuracy of 97% with searching algorithm in video-matching experiments and 98.62% with automation algorithm in copyright-protection experiments. Therefore, this system could form a core technology that identifies illegal content and automatically excludes access to illegal content by many video service sites.     

A novel dynamic pricing scheme for contributing peers in the VoD system

In this paper we have proposed a dynamic pricing scheme for the contributing peers in the Video on Demand (VoD) system. The scheme provides an effective mechanism to maximize the profit through the residual resources of the contributing peers. A utilization function is executed for each contributing peer to estimate the utility factor based on the parameters such as initial setup cost, holding cost, chaining cost and salvage cost. In this paper, we urge an effective dynamic pricing algorithm that efficiently utilizes a range of parameters with a varying degree of complexity. The key findings of the algorithm are (i) each contributing peers are benefitted by the monetary based on its resource contributions to the VoD system and (ii) a high degree of social optimum is established by proficiently aggregating the contributing peer’s resources with the overall resources of the VoD system. We validate our claim by simulating the proposed dynamic pricing scheme with other standard pricing schemes such as altruism, cost model and game theory perspective. The result of our dynamic pricing scheme shows the best utility factor than other standard pricing schemes.     

Effect of stress-strain-law transients on formability

The effect of work-hardening changes, of the type that follow a rapid change of strain state or strain rate, on formability has been investigated using finite element modeling (FEM). A standard sheet tensile test was chosen as an arbitrary forming operation and a rigid-viscoplastic FEM program was employed for analysis. In each case, a transitional region of true strains between 0.1 and 0.2 was modeled. Transients involving lowered work-hardening rates (negative value of An) promoted increased strain localization and premature failure while transients with increased work-hardening rates enhanced formability. Total engineering elongations (50 mm gage length) varied between 20 pct and 46 pct, illustrating the importance of the transient far beyond the transient region. The controlling factor is the effective work-hardening rate in the transient region rather than the change in strength coefficient or flow stressper se. A direct stress offset of the flow curve { } also affects strain localization through a change in effective work-hardening rate.     

Multidisciplinary optimization of gas-quenching process

Distortion as a result of the quenching process is predominantly due to the thermal gradient and phase transformations within the component. Compared with traditional liquid quenching, the thermal boundary conditions during gas quenching are relatively simple to control. By adjusting the gas-quenching furnace pressure, the flow speed, or the spray nozzle configuration, the heat-transfer coefficients can be designed in terms of both the component geometry and the quenching time. The purpose of this research is to apply the optimization methodology to design the gas-quenching process. The design objective is to minimize the distortion caused by quenching. Constraints on the average surface hardness, and its distribution and residual stress are imposed. The heat-transfer coefficients are used as design variables. DEFORM-HT is used to predict material response during quenching. The response surface method is used to obtain the analytical models of the objective function and constraints in terms of the design variables. Once the response surfaces of the objective and constraints are obtained, they are used to search for the optimum heat-transfer coefficients. This process is then used instead of the finite-element analysis. A one-gear blank case study is used to demonstrate the optimization scheme.