已二醇二丙烯酸酯对真丝的接枝改性研究

研究了用二醇二丙烯酸酯为接枝单体、过硫酸铵（APS）为引发剂对真丝的接枝共聚反应，分析了接枝率的影响素，并测试了改性真丝的主要应用性能。结果表明：乳液和乙醇/水为溶剂的2种体系都能在真丝上获得较高接枝率。对于乙醇/水体系v(乙醇）：v(H2O）=1:1，接枝单体20～30g/L,2%甲酸4ml，引发剂APS 0.5g/L,65～70℃接枝60min的接枝率高。改性后真丝的断裂强度、延伸度、吸湿性能都可获得改善，对酸、碱的溶解性提高，但染色性能提高不明显，对泛黄性改善一般。     

宜昌站泄流能力变化对葛洲坝设计洪水影响

宜昌水文站是葛洲坝、三峡水利枢纽的设计依据站。葛洲坝水利枢纽动工修建和运行 ,对该站水位流量关系中低水部分产生了影响。探讨了该河段泄流能力的变化对葛洲坝水利枢纽设计洪水有无影响的问题。用1 967～ 1 999年实测资料对宜昌站以汛期平均水位为参数的水位流量关系曲线簇进行了检验 ,大部分年份最大日平均流量、3、7、1 5、30d洪量的偏差在± 4 %之间 ,说明曲线簇推流具有相当的精度。证明了宜昌河段中低水泄流能力的变化对葛洲坝水利枢纽设计流量和校核流量基本没有影响     

电子封装用金属基复合材料的制备

分析了电子封装用金属基复合材料的性能特点及其对制备工艺的要求，在此基础上论述了该种材料的各种制备工艺的特点及发展现状。     

Shear ductility and toughenability study of highly cross-linked epoxy/polyethersulphone

The objective of the present study was to determine whether the ductility and toughenability of a highly cross-linked epoxy resin, which has a high glass transition temperature, T _g, can be enhanced by the incorporation of a ductile thermoplastic resin. Diglycidyl ether of bisphenol-A (DGEBA) cured by diamino diphenyl sulphone (DDS) was used as the base resin. Polyethersulphone (PES) was used as the thermoplastic modifier. Fracture toughness and shear ductility tests were performed to characterize the materials. The fracture toughness of the DDS-cured epoxy was not enhanced by simply adding PES. However, in the presence of rubber particles as a third component, the toughness of the PES–rubber-modified epoxy was found to improve with increasing PES content. The toughening mechanisms were determined to be rubber cavitation, followed by plastic deformation of the matrix resin. It was also determined, through uniaxial compression tests, that the shear ductility of the DDS-cured epoxy was enhanced by the incorporation of PES. These results imply that the intrinsic ductility, which had been enhanced by the PES addition, was only activated under the stress state change due to the cavitation of the rubber particles. The availability of increasing matrix ductility seems to be responsible for the increase in toughness. This revised version was published online in November 2006 with corrections to the Cover Date.     

高炉鼓风机就地扩容改造方案及经济效益

介绍了利用高炉鼓风机基础实施不易地扩容改造的设计工艺方法，该方法不仅降低了设计、施工、安装费用，而且缩短了施工周期，降低了固定资产投资。     

大化水电站通航建筑物型式的再研究

本文较详细介绍了大化通航建筑的研究过程并针对大化水电站的现状，论证分析了大化水电站升船机改型为船闸的可能性，技术上的优越性和经济上的合理性，是较好的合理化建议文章。     

G104-5P42分支水平井钻井液工艺技术

G104-5P42井是在高尚堡G104-5区块构造较高部位部署的一口重点开发井，也是冀东油田第一口鱼骨型水平分支井，钻探目的是开发高浅北区Ng12油层，挖掘高浅北区井间剩余油潜力。该井主井眼斜深为2388m，水平位移为736．42m，水平段长243m，第一分支斜深为2342m，水平段长120．25m，水平位移为682．14m，第二分支斜深为2421m，水平段长117m，水平位移为761．73m。三开选用无固相甲酸盐聚合醇钻井液，在钻进油气层前加入GN-YBJ-I保护剂。应用结果表明，无固相甲酸盐聚合醇钻井液具有好的防塌能力和润滑减阻效果，性能稳定、黏度、切力较低，有利于减少环空压力损耗；在油气层段密度控制在1．08g／cm^3以内，为近年来同区块密度使用最低井，减小了有害固相及滤液对储层的伤害密度，经测试该井获高产油流；该井全井平均机械钻速为15．09m／h，钻井周期比原设计提前15d。该体系的配制及维护成本较高，适宜在目的层井段使用，但可回收再利用。     

4×622Mb／sWDM40km光通信系统实验

本文完成了我国第一个４×６２２Ｍｂ／ｓ波分复用（ＷＤＭ）光通信系统实验，使单根光纤线路通信容量达２．４Ｇｂ／ｓ。该系统以ＤＦＢ－ＬＤ为光源，工作波长在１．５５μｍ附近，ＬＤ的工作频率稳定度优于±１５０ＭＨｚ，信道间隔２ｎｍ左右，无中继传输距离为４３．６ｋｍ，采用Ｆ－Ｐ调谐光滤波器作为解复用器，接收机灵敏度达－３０ｄＢｍ。     

As压对LT-GaAs/AlGaAs多量子阱光学特性的影响

在衬底温度为 3 5 0°C的条件下 ,用分子束外延的方法 ,在不同的砷压条件下生长了 Ga As/Al0 .3Ga0 .7As多量子阱结构。 77K的荧光实验证明 ,砷压对样品的光学特性影响显著。认为砷压对低温多量子阱光学特性的影响是点缺陷随砷压的演化和能级间相互补偿的共同结果。通过优化砷压 ,样品的荧光峰的半峰宽减小到 3 me V,这是到目前为止所报道过的最窄的低温多量子阱的荧光峰。相应的垂直场光折变器件的电吸收为 60 0 0 cm     

Bright Blue Light—emitting Diodes Based on a Novel Fluorescent Dye Containing Heterocyclic Groups

Novel molecular material ,1-benzothiazoly-3-pheny1-pyrazoline (BTPP) was found to function as bright blue light emitting dye in organic electroluminescent device, and its optical and electric characteristics were investigated. This heterovyclic compound exhibited good characteristics of blue photoluminescence and electroluminescence,which had the emission peak at 450nm .The single layer light-emitting devices using BTPP as light -emitting material dispersed in poly(N-vinylcarbazole)(PVK) and double layer ones using PBD as hole block layer above the light-emitting layer were fabricated using conventional spin-casting and vaccum vapour deposition methods. The introduction of PBD has enhanced electron injection and luminance efficiency, compared with the single layer LEDs.