位置灵敏塑料探测器阵列

本文描述了一个有效探测面积为100×70cm~2的位置灵敏塑料闪烁探测器阵列,它由两条100×5×1cm和6条100×10×1cm的Pilot U型塑料闪烁体组成。用~(252)Cfα放射源测得10cm宽的闪烁体的时间分辨、位置分辨和能量分辨分别为740ps,5.7cm和60％;5cm宽的闪烁体分别为610ps,4.7cm和40％。     

Delay-dependent state estimation for delayed neural networks

In this letter, the delay-dependent state estimation problem for neural networks with time-varying delay is investigated. A delay-dependent criterion is established to estimate the neuron states through available output measurements such that the dynamics of the estimation error is globally exponentially stable. The proposed method is based on the free-weighting matrix approach and is applicable to the case that the derivative of a time-varying delay takes any value. An algorithm is presented to compute the state estimator. Finally, a numerical example is given to demonstrate the effectiveness of this approach and the improvement over existing ones.     

银狐皮毛被及皮板组织构造的研究

用光学显微镜和扫描电镜观察了国产人工饲养银狐的毛被和皮板组织构造 ,测定了毛的长度、细度、密度、毛的鳞片高度和皮板厚度。提供了毛和皮板组织学图片 15幅。     

莺-琼盆地生物气及生物—低成熟过渡带气特征与勘探前景

莺 琼盆地天然气资源丰富 ,天然气成因类型多 ,迄今为止 ,除在该区浅层和中深层发现以成熟—高成熟的热成因腐殖型气 (煤型气 )为主的天然气藏外 ,也发现了一些生物气及生物—低成熟过渡带气气藏 ,且均具较高的产量和一定的储量规模 ,其勘探前景广阔。     

The influence of the fabrication process on the buckling of thin-walled steel box sections

Steel box sections are usually fabricated from flat plates which are welded at the corners. The welding process can introduce residual stresses and geometric imperfections into the sections which can influence their strength. For some thin-walled sections, large periodic geometric imperfections have been observed in manufactured sections. Subsequent investigations have indicated that the imperfections are in fact buckling deformations i.e. the box section has buckled due to welding residual stresses prior to any application of external load. The welding procedure and the behaviour of the box sections under load has been modelled using a finite element analysis that accounts for both geometric and material non-linearities. Tests have been carried out on box sections with a range of width to thickness ratios for the plate elements. Modelling has been shown to give good correlation with the test results. The conditions for buckling to take place as a result of the welding process have been established. A design method has been proposed.     

Systematic characterization of Cl2 reactive ion etchingfor improved ohmics in AlGaN/GaN HEMTs

Pre-metal-deposition reactive ion etching (RIE) was performed on an Al_0.3Ga_0.7N/AlN/GaN heterostructure in order to improve the metal-to-semiconductor contact resistance. An optimum AlGaN thickness for minimizing contact resistance was determined. An initial decrease in contact resistance with etching time was explained in terms of removal of an oxide surface layer and/or by an increase in tunnelling current with the decrease of the AlGaN thickness. The presence of a dissimilar surface layer was confirmed by an initial nonuniform etch depth rate. An increase in contact resistance for deeper etches was experienced. The increase was related to depletion of the two-dimensional (2-D) electron gas (2-DEG) under the ohmics. Etch depths were measured by atomic force microscopy (AFM). The contact resistance decreased from about 0.45 Ωmm for unetched ohmics to a minimum of 0.27 Ωmm for 70 Å etched ohmics. The initial thickness of the AlGaN layer was 250 Å. The decrease in contact resistance, without excessive complications on device processing, supports RIE etching as a viable solution to improve ohmic contact resistance in AlGaN/GaN HEMTs     

WDM传输系统中泵浦配置对光纤拉曼放大器增益特性的影响

通过理论分析和模拟运算,研究了光纤拉曼放大器泵浦优化的一般规律。     

激光熔覆Ni基SiC合金涂层组织与性能的研究

利用5kWCO2连续波激光器在16Mn钢基材表面对含20%(体积比)SiC陶瓷粉末的镍基自熔性合金粉末进行激光熔覆得到Ni基SiC合金涂层(NiSiC)。研究了合金涂层的组织形貌及相结构,并用单纯的镍基合金涂层(Ni60)进行了显微硬度及滑动磨损性能的对比试验。结果表明,NiSiC合金涂层由γ枝晶及其间的共晶组织组成,主要组成相为γ-Ni,γ-(Ni,Fe)固溶体和(Cr,Fe)7C3,Cr23C6及(Cr,Si)3Ni3Si等化合物。添加SiC的镍基合金涂层NiSiC比单纯的镍基合金涂层Ni60具有较高的硬度和耐磨性。     

软交换网络中媒体网关控制器的研究与设计

300万像素对于专业摄影来说可能不值一提，但是对于家庭用户而言却已经十分完美了。下面三款数码相机是300万家庭中令人兴奋的新品，它们的价格都在3000元到4000元人民币之间，想想一年前3000万像素的相机要花多少钱？而在测试中它们的表现也的确让人觉得物有所值。     

环保型隧道防火涂料的研究

介绍了国内外公路隧道、铁路隧道及地铁火灾情况 ,研制出一种可在潮湿环境中使用、火灾发生时无有害气体产生的环保型隧道防火涂料。涂层厚度 18～2 0 mm,耐火极限达 3小时。为防止涂料加水拌和后沉淀分层 ,增加涂料的和易性 ,研制出一种分散剂。