Iterative detection/decoding for two-track partial response channels

In this letter, we investigate the iterative detection/decoding algorithms for two-track partial response channels. We first describe the iterative algorithm as an iterative message-passing/processing algorithm over a high-level normal graph and then propose two trellis-based detection algorithms. The natural one is based on a joint trellis, which can be implemented for low-order channels. For moderate-order channels, we propose a separated detection, which is based on two single-track trellises. Compared with the joint detection, the separated detection is simpler in most cases. Simulation results show that, for two-track EPR4 channels with minor intertrack interferences, the separated detection causes only marginal degradation in performance.     

基于MPEG-2文件的合并

介绍了具有相同音频、视频编码方式的MPEG - 2节目流如何合并成一个节目流。合并后的文件播放流畅并且时间显示正确 ,它包括PATPMT表的重写 ,系统头部分相关字段的更改 ,PCR值的修改 ,解码时间标签 (DTS)和显示时间标签 (PTS)的重新确定 ,传送速率的修改以及添加相应的空包     

ADN氧化剂的合成及其在推进剂中的应用

综述了ADN的合成、性质及其在推进剂中的应用，认为球形ADN具有能量高、感度低、特征信号低，对环境无污染等优点，将其作为氧化剂在高能低特征信号推进剂中有着广阔的应用前景。     

基于手写笔的多功能电子白板系统的实现

该文针对当前电子白板系统对个性化支持的不足,引入手写笔作为输入设备,充分利用其功能参数,设计开发了具有模拟毛笔、钢笔、铅笔等真实笔特征的多笔型功能的电子白板系统。     

涤纶工业丝环吹风改造的设计计算

应用PET纤维的冷却成形理论 ,结合空气调节的相关知识 ,提出了环吹风的设计计算方法 ,对涤纶工业丝环吹风进行了设计改造 ,满足了纺丝工艺要求     

半导体量子点中极化子的有效质量

研究了半导体量子点中极化子的有效质量.采用改进的线性组合算符方法,导出在电子-体纵光学声子(LO)强耦合时抛物量子点中极化子的振动频率、相互作用能和有效质量随受限强度和电子-声子耦合强度的变化.对RbCl晶体量子点进行了数值计算,结果表明,量子点受限越强,半导体量子点中强耦合极化子的振动频率和有效质量就越大;极化子的相互作用能随受限强度的增加先急剧增加,当达到极值后,随受限强度的增加而急剧减少     

CSTN-LCD用铬版清洗效果的改善

利用铬版清洗机对CSTN-LCD用铬版进行清洗处理,分析了清洗过程中出现的铬层脱落现象,铬层脱落与轴向喷射压力和水平切力密切相关,通过调整转速和喷射压力探索了安全使用条件:在转速不超过1000r/min,喷射压力低于0.5×105Pa的情况下使用铬版清洗机进行清洗是相对安全的。同时采用预清洗处理的方法满足清洁要求,使换线时间由平均3h缩短到平均1h以内,年产能提高270000片。     

锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

End‐Capping as a Method for Improving Carrier Injection in Electrophosphorescent Light‐Emitting Diodes

The electronic properties, carrier injection, and transport into poly(9,9‐dioctylfluorene) (PFO), PFO end‐capped with hole‐transporting moieties (HTM), PFO–HTM, and PFO end‐capped with electron‐transporting moieties (ETM), PFO–ETM, were investigated. The data demonstrate that charge injection and transport can be tuned by end‐capping with HTM and ETM, without significantly altering the electronic properties of the conjugated backbone. End‐capping with ETM resulted in more closely balanced charge injection and transport. Single‐layer electrophosphorescent light‐emitting diodes (LEDs), fabricated from PFO, PFO–HTM and PFO–ETM as hosts and tris[2,5‐bis‐2′‐(9′,9′‐dihexylfluorene)pyridine‐κ²NC_3′]iridium(III ), Ir(HFP)₃ as the guest, emitted red light with brightnesses of 2040 cd m^–2, 1940 cd m^–2 and 2490 cd m^–2 at 290 mA cm^–2 (16 V) and with luminance efficiencies of 1.4 cd A^–1, 1.4 cd A^–1 and 1.8 cd A^–1 at 4.5 mA cm^–2 for PFO, PFO–HTM, and PFO–ETM, respectively.