Submerged yeast fermentation of acid cheese whey for protein production and pollution potential reduction

Bench-scale batch bioreactors were used to study the effectiveness of cheese whey fermentation for single-cell protein production using the yeast Kluyveromyces fragilis in reducing the pollution potential of whey as measured by solids, chemical oxygen demand (COD) and nitrogenous compounds concentrations. The four principal phases (lag, exponential, stationary and death) encountered in the history of a microbial culture grown under batch conditions were clearly recognized in the growth, temperature and dissolved oxygen curves. The lactose concentration and soluble COD displayed three distinct phases corresponding to the lag, exponential and stationary phases of the yeast growth. The minimum dissolved oxygen and maximum temperature observed in this study (at an air flow of 3 VVM, a mixing speed of 400 rpm and an ambient temperature) were 2.49 mg/L and 31.6 degrees C, respectively. About 99% of lactose (90.6% of soluble COD) was utilized after 28 h. The total COD continued to decline due to cell death resulting in a reduction of 42.98%. The total nitrogen concentration remained unchanged while the organic nitrogen increased during the exponential phase and then declined during the death phase. The ash content remained unchanged while a substantial reduction (56%) of the volatile solids was observed. These results indicated that sufficient oxygen for yeast growth was present in the medium and no cooling system was needed for this type of fermenter under similar experimental conditions. Recovering the yeast biomass with ultrafiltration reduced the total COD by 98% of its initial value in the raw whey.     

The effect of surface roughness on the efficiency of the cyclic potentiodynamic passivation (CPP) method in the improvement of general and pitting corrosion resistance of 316LVM stainless steel

The influence of surface roughness on the efficiency of a cyclic potentiodynamic passivation (CPP) method employed to increase the general and pitting corrosion resistance of 316LVM stainless steel was investigated. The results show that a decrease in surface roughness of both the surface on which the passive film was formed naturally and by the CPP method, results in an increase in general corrosion resistance of the material, while for the CPP-modified surface, a notable increase in pitting corrosion resistance was also observed. It was further demonstrated that the CPP method is highly effective in increasing the general and pitting corrosion resistance of 316LVM, and that its efficiency does not depend on the surface roughness.     

Passivation of pigment-grade TiO(2) particles by nanothick atomic layer deposited SiO(2) films

Pigment-grade TiO(2) particles were passivated using nanothick insulating films fabricated by atomic layer deposition (ALD). Conformal SiO(2) and Al(2)O(3) layers were coated onto anatase and rutile powders in a fluidized bed reactor. SiO(2) films were deposited using tris-dimethylaminosilane (TDMAS) and H(2)O(2) at 500?°C. Trimethylaluminum and water were used as precursors for Al(2)O(3) ALD at 177?°C. The photocatalytic activity of anatase pigment-grade TiO(2) was decreased by 98% after the deposition of 2?nm SiO(2) films. H(2)SO(4) digest tests were performed to exhibit the pinhole-free nature of the coatings and the TiO(2) digest rate was 40 times faster for uncoated TiO(2) than SiO(2) coated over a 24?h period. Mass spectrometry was used to monitor reaction progress and allowed for dosing time optimization. These results demonstrate that the TDMAS-H(2)O(2) chemistry can deposit high quality, fully dense SiO(2) films on high radius of curvature substrates. Particle ALD is a viable passivation method for pigment-grade TiO(2) particles.     

Electron thermal microscopy

We present real-time, nanoscale temperature mapping using a transmission electron microscope and standard phase transitions in metal islands. Islands are deposited on the reverse side of commercially available silicon nitride membranes, while local thermal gradients are produced by Joule heating in a thin wire on the front side of the membrane. Change in contrast due to the liquid-solid transition in the islands allows the mapping of absolute temperature, as above or below the transition temperature, over the entire field-of-view. Experiments demonstrate nanoscale (<100 nm) resolution and video-rate (>30 thermal-images per second) speed, supported by combined electrical and thermal modeling. This provides a generic and adaptable platform for nanoscale thermal characterization independent of strong probe coupling and optical effects.     

Effect of Nitrogen Alloying on Sulphur Behaviour during ESR of AISI M41 Steel

In this work, the effects of nitrogen alloying, physical properties and chemical composition of slag used in electro‐slag refining (ESR) on phosphorus and sulphur contents of AISI M41 high speed steel have been studied. The experiments were conducted with two high speed steel grades which were melted in an induction furnace (IF). The first grade is the standard AISI M41 high‐speed steel and the second one is nitrogen alloyed M41 (denoted M41N). The produced ingots were ESR remelted under three grades of calcium fluoride based slag. Results showed that the ESR process has no effect on the phosphorus content in steel but it is a good tool in removing sulphur. This study shows that a high desulphurization rate can be achieved by ESR process by optimizing slag properties where the viscosity and oxidation reactions play an important role in sulphur removal. Nitrogen alloying was found to retard sulphur removal.     

Impact of the penetration of distributed generation on optimal reactive power dispatch

Optimal reactive power dispatch (ORPD) is a complex and non-linear problem, and is one of the sub-problems of optimal power flow (OPF) in a power system. ORPD is formulated as a single-objective problem to minimize the active power loss in a transmission system. In this work, power from distributed generation (DG) is integrated into a conventional power system and the ORPD problem is solved to minimize transmission line power loss. It proves that the application of DG not only contributes to power loss minimization and improvement of system stability but also reduces energy consumption from the conventional sources. A recently proposed meta-heuristic algorithm known as the JAYA algorithm is applied to the standard IEEE 14, 30, 57 and 118 bus systems to solve the newly developed ORPD problem with the incorporation of DG. The simulation results prove the superiority of the JAYA algorithm over others. The respective optimal values of DG power that should be injected into the four IEEE test systems to obtain the minimum transmission line power losses are also provided.     

Effect of wettability on oil recovery and breakthrough time for immiscible gas flooding

The effect of wettability on oil recovery at higher water saturation is still not fully understood, especially in the case of mixed wettability. This study was conducted to examine the effects of wettability on oil recovery and breakthrough time through experiments for two wettability conditions (water-wet and mixed-wet) and three water saturations (20%, 40%, and 60%). Clashach sandstone core with a porosity of 12.8% and a permeability of 75 md was utilized as the porous media. Immiscible gas flooding was performed by injecting nitrogen gas into the core at room temperature and pressure. The results showed 54.3% and 48.8% of the initial oil in place (IOIP) as the ultimate oil recovery at 40% water saturation from mixed-wet core and water-wet core respectively. In contrast, the water-wet core displayed better results (32.6% of the IOIP) in terms of breakthrough time compared to the results of water-wet core (10.6% of the IOIP) at the same water saturation. In conclusion, oil recovery was found highly dependent on water saturation while breakthrough time was mainly affected by the wettability of the cores.     

Dynamic cell fractionation and transportation using moving dielectrophoresis

This study presents a new cell manipulation method using a moving dielectrophoretic force to transport or fractionate cells along a microfluidic channel. The proposed moving dielectrophoresis (mDEP) is generated by sequentially energizing a single electrode or an array of electrodes to form an electric field that moves cells continuously along the microchannel. Cell fractionation is controlled by the applied electrical frequency, and cell transportation is controlled by the interelectrode activation time. The applicability of this method was demonstrated to simultaneously fractionate and transport Saccharomyces cerevisiae yeast cells, both viable and nonviable, by operating at conditions under which the cells were subjected to positive and negative dielectrophoresis, respectively. Compared to the conventional dielectrophoresis (cDEP and traveling wave dielectrophoresis (twDEP), moving dielectrophoresis allows cells to be separated on the basis of the real part of the Clausius-Mossotti factor, as in cDEP, but yet allows the direct transportation of separated cells without using fluid flow, as in twDEP. This dielectrophoresis technique provides a new way to manipulate cells and can be readily implemented on programmable multielectrode devices.     

Thermal effect in hydrodynamic lubrication of line contacts-Piezoviscous effect neglected

Thermal effect in high-speed rolling element bearings has been investigated numerically following a computationally efficient method developed by Elrod and Brewe [11. Viscous shear heating effects on both film thickness and rolling friction are investigated for a line-contact geometry assuming fully flooded lubrication. Thermal load-carrying capacity and rolling friction of the line contact have been numerically calculated for varying rolling speeds from 5 to 40 m/s and dimensionless film thickness between 10⁻⁴ and 10⁻³. Results indicate marked influence of viscous shear heating on the load-carrying capacity, film thickness and rolling traction at high rolling speeds. Neglecting thermal effect at high rolling speeds would lead to gross overestimation of load capacity, film thickness and traction. Results are presented for pressure and temperature distribution within the contact for various rolling speeds and film thicknesses.     

Structural characterization of grain pattern diversity in parametric space

Grain patterns are characterized by size and shape diversity as reflected by variations in the values of structural parameters ascribed to them. Analysis of the population of grains calls for a global analysis of all the pertinent structural parameters taken together. In this study, algorithms were developed for advanced grain image analysis, unbiased grain size-side measurement and full grain pattern recognition. The correlations of these normalized structural parameters were studied for each topological class and geometrical group, for the grain patterns formed under different nucleation-growth conditions. Relationships between the structural parameters and the grain spatial coordinates are given. This provides a useful approach to investigate the structural inhomogeneity in grain patterns. The results show strong interdependence between the topology, geometry and physical dynamics of the spherulitic grain size-shape arrangement in semi-crystalline polymeric films.