High-voltage bridge for measuring spontaneous polarization,dielectric constants,and conductivity of ferroelectric crystals

Translated from Izmeritel'naya Tekhnika, No. 9, pp. 34–35, September, 1989.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.     

Tube-shaping unit — A way of improving the quality of shaped tubes

Lenin Dnepropetrovsk Pipe Plant. Translated from Metallurg, No. 8, p. 39, August, 1989.     

Occupational airway diseases in the metalworking industry Part 1: Respiratory infections, pneumonia, chronic bronchitis and emphysema

Occupational airway diseases are now receiving attention in industry, although study is hampered by a lack of readily-available data. The interpretation of the data that is available, and also of the root problems themselves, is itself a difficult problem. This paper has been written as a literature review which it is hoped that other researchers can take either as a starting point or as a refresher.     

“Metallisation” of oxide surfaces observed by in situ high-resolution electron microscopy

Intense irradiation (25–40 A/cm²) at intermediate energy (400 keV) has been found to cause “metallisation” of tungsten oxide and titanium niobate crystal surfaces. The possible mechanisms and the likely consequences for high-resolution imaging of clean oxide surfaces are briefly discussed.     

The contact of elastic regular wavy surfaces

A complete solution in closed form to the elastic contact of a one-dimensional sinusoidal surface with a flat surface was presented by Westergaard in 1939. This paper is concerned with the elastic contact of a two-dimensional sinusoidal surface with a flat. In this case the stress distribution within the elastic solids is three-dimensional. As the load is increased the contact areas change in shape from being circular to square and finally leave a circular region of no contact when the waves are almost squashed flat. The problem is solved in general using a numerical method due to Kalker, but asymptotic solutions in closed form have been found for light loads and also for heavy loads at which contact is almost complete. The variation of the mean separation with load, which determines the volume of the space trapped between the two surfaces, is also found.     

The effect of a solid additive on rolling fatigue life

Behaviour of a series of lubricant oils and the effect of a non stoichiometric inorganic compound, as solid extreme pressure additive, on rolling fatigue life are studied using the rolling four-ball accelerated service simulation test proposed by Barwell and Scott. The results show, in all tested cases, the remarkable efficacy of this type of additive. The Total Acidity Number (tan) was found to increase with performance time for the case of the base lubricant, while for the oils with additives, it remained at its constant low value. This led to a proposal of a possible mechanism of the additive performance in the rolling process.