Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers

In this paper, polyborosilazane precursor was synthesied from HMDZ, HSiCl₃, BCl₃ and CH₃NH₂ using a multistep method. By controlling the storage conditions, parts of the polyborosilazane fibers were hydrolyzed. FT-IR, NMR, XRD, TEM and monofilament tensile strength test were employed to study the effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers. FT-IR and NMR results indicate that Si-N group in PBSZ reacts with H₂O to form Si-O-Si group. After pyrolysis reaction at 1400℃, Si-O-Si group will finally transformed into highly ordered cristobalite and β-quartz, resulting in formation of the wrinkled surface of the obtained SiBN ceramic fiber. The strip-like defects on fiber surface, according to monofilament tensile strength test, had a significant effect on mechanical property of the obtained SiBN ceramic fiber and caused no increase in fiber tensile strength of hydrolytic polyborosilazane fiber before and after pyrolytic process.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

超高效液相色谱—串联质谱法快速同时检测茶叶中7种香料

基于超高效液相色谱—串联质谱(UHPLC-MS/MS),建立了同时检测茶叶中7种可能非法添加的香料(茴香烯、香豆素、胡椒酚甲醚、指甲花醌、甲基丁香酚、蒲勒酮和反式肉桂醛)的定性、定量方法。茶叶样品经过乙腈—水混合溶剂提取,涡旋振荡,适当稀释并加入无水硫酸钠、十八烷基键合硅胶(C₁₈)和N-丙基乙二胺(PSA)进行净化,涡旋离心后,上清液过膜待测。以Kinetex C₁₈色谱柱分离,在多反应检测扫描(MRM)模式下经MS/MS进行基质外标法定量检测。试验结果表明,7种目标物在0.8~1 600.0 μg/L范围内呈良好线性,线性相关系数(R2)均大于0.999。方法的检出限为0.02~0.03 mg/kg,定量限为0.05~0.10 mg/kg,平均回收率为82.5%~102.5%,日内、日间精密度分别小于16%和18%。该方法快速、可靠、灵敏度高,用于检测市面流通的100个茶叶样品,结果检出了反式茴香脑、香豆素和胡椒酚甲醚等物质,最大浓度值分别为65.0,2.0,72.2 mg/kg。     

低剂量抑制剂Inhibex501存在下的甲烷水合物相平衡研究

含动力学抑制剂的天然气水合物相平衡研究对新型低剂量抑制剂的开发具有指导作用。在283.6 ~ 290.9 K和7.51 MPa ~ 15.97 MPa的温压范围内研究了抑制剂Inhibex501及其溶剂2-乙二醇单丁醚对甲烷水合物相平衡条件的影响。实验结果显示，0.5wt%和2.0wt%浓度的Inhibex501对甲烷水合物形成的热力学条件具有促进作用，能使甲烷水合物形成移向更高的温度或者更低的压力，而2-乙二醇单丁醚在浓度0.2wt% ~ 1.0wt%范围几乎不改变甲烷水合物形成的热力学条件，N-乙烯基己内酰胺与N-乙烯基吡咯烷酮的共聚物对水合物形成热力学条件的改变起主要作用。     

Zinc doped Fe2O3 for boosting Electrocatalytic Nitrogen Fixation to ammonia under mild conditions

Artificial nitrogen fixation is emerging as a promising approach for synthesis of ammonia at mild conditions. Inspired by biological nitrogen fixation based on bacteria containing iron, zinc doped Fe₂O₃ nanoparticles are proposed as an efficient and earth abundant electrocatalyst for converting N₂ to NH₃. In neutral media, it achieves a maximum Faradaic efficiency (FE) of 10.4% and a large NH₃ yield rate of 15.1 μg h^?1 mg^?1_cat. at ?0.5 V vs. reversible hydrogen electrode. This catalyst also exhibits excellent selectivity and stability. Theoretical calculations suggest the reaction follows the associative enzymatic mechanism and it has a barrier of as low as 0.68 eV.