X60管线钢疲劳特性的研究

利用2、4和14mm的X60钢紧凑拉伸试样进行同样应力水平、固定应力比（R＝0．1）的疲劳裂纹扩展试验，揭示出高韧性管道钢的疲劳裂纹扩展存在显著的厚度效应。由于应力水平低，相应的离面应力也低，不足以导致分层开裂，因此，裂纹端部的三维应力约束随厚度增加而增大。4mm试样的疲劳裂纹速率远高于2mm试样，但厚度再增大，裂纹扩展速率不再有显著变化。进一步对表面裂纹试样进行疲劳裂纹扩展试验，并用勾线法纪录裂纹扩展情况，利用穿透裂纹的da/dN-ΔK曲线预测表面裂纹扩展，用2mm厚试样的数据控制裂纹表面长度的扩展，用14mm厚试样的数据控制裂纹底部沿厚度方面的扩展，得到了与表面裂纹扩展实验吻合很好的预测结果。     

黄河龙青段主要环境工程地质问题分析思路

介绍了黄河上游龙青段主要环境工程地质问题的分析思路，以达到抛砖引玉，交流和提高电工程地质勘测水平的目的。     

超大型材生产经验

对几种超大型材挤压生产的工艺技术、工模具设计、挤压参数控制等过程进行了分析，通过例子总结了挤压生产超大型材的经验及关键技术。     

Trace elements in particles of motor vehicle exhaust in Shanghai

A nuclear microprobe with high spatial resolution and high analytical sensitivity was applied to analyze trace elements,especially lead,in vehicle exhaust of Shanghai city.The result shows that the chemical composition and its corresponding x-ray relative intensity are different among different vehicle exhausts.There are many kinds of metal elements in particles of vehicle exhaust.most are harmful to people,such as Ti,Cr,Mn,Pb,etc.We found that the lead concentration was 6820μg/g and the bromine concentration was 5300μg/g in the exhaust from Santana using leaded gasoline(SULG).which is higher than any other kinds of vehicle exhausts.We have also detected the minimum lead in the particles of unleaded gasoline and its content varies from one to another.Its mean concentration was 450μg/g and the highest reached 6210μg/g.The unleaded gasoline‘s Pb existed in the whole particle while the leaded gasoline‘s enriched in the surface of the particle and was more harmful to the human beings.     

啤酒标签用铝箔力学性能研究

分析研究了连续铸轧坯料的合金成分，冶金组织和热处理工艺对啤酒标用铝箔力学性能的影响，选定成形性优良的合金系列，并优化铸轧工艺和热处理工艺是提高铝箔力学性能的关键。     

建筑墙体表面传热系数辨识研究

对实验房间南向墙体内表面中心区域的换热过程进行实验，发现当风速在0－5．5m/s之间时，表面传热系数在8－18W（m^2.K）之间波动，而风向对墙体表面传热系数影响不大；用辅助变量法分析墙体表面传热过程，并结合实验推导出墙体表面传热系数。模型的预测结果与实测结果吻合良好。     

DVD视盘机的电磁骚扰抑制

本文讨论对DVD视盘机的电磁骚扰的抑制，使其电磁骚扰水平符合有关标准的要求，不成为新的电磁环境中的污染源。     

Synthesis and Characterization of Poly （L-lactide-co-ε-caprolactone） Copolymers

A series of random and block poly（ L-lactide-co-e-caprolactone ） （ PCLA ） copolymers whh different composition are prepared using stannous octaoate as catalyst.The effects of the amount of initiator on the intrinsic viscosity have been investigated. The structure of the PCLA copolymers is characterized by means of nuclear magnetic resonance（ NMR ）, Fourier transform infrared spectrum （ FTIR ）, differential scanning calorimetry （ DSC ） and X- ray diffraction （ XRD ） methods. It is shown that the synthesis condition and the composition of copolymers obrious influence on the structure of PCLA copolymers. Hydrolytic degradation of the copolymers in a PBS solution of pH 7.4 at 37.0℃ shows that the copolymers of different composhions degrade at different rates.     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

西霞院水利枢纽工程泄洪闸振冲碎石桩基础处理

通过西霞院水利枢纽工程泄洪闸振冲碎石桩基础处理施工方法论述,给出了加砂层振冲碎石桩施工造孔水压、水量、成孔速度、填料级配、填料方法以及振密电流值、留振时间等施工控制参数。