Working conditions in the engine department – A qualitative study among engine room personnel on board Swedish merchant ships

The specific problems associated with the work on board within the merchant fleet are well known and have over the years been a topic of discussion. The work conditions in the engine room (ER) are demanding due to, e.g. the thermal climate, noise and awkward working postures. The work in the engine control room (ECR) has over recent years undergone major changes, mainly due to the introduction of computers on board. In order to capture the impact these changes had implied, and also to investigate how the work situation has developed, a total of 20 engine officers and engine ratings were interviewed. The interviews were semi-structured and Grounded Theory was used for the data analysis. The aim of the present study was to describe how the engine crew perceive their work situation and working environment on board. Further, the aim was to identify areas for improvements which the engine crew consider especially important for a safe and effective work environment. The result of the study shows that the design of the ECR and ER is crucial for how different tasks are performed. Design which does not support operational procedures and how tasks are performed risk inducing inappropriate behaviour as the crew members’ are compelled to find alternative ways to perform their tasks in order to get the job done. These types of behaviour can induce an increased risk of exposure to hazardous substances and the engine crew members becoming injured.     

Relating the X-band opacity of a tropical tree canopy to sapflow, rain interception and dew formation

During summer and autumn 2007, a 11 GHz microwave radiometer was deployed in an experimental tree plantation in Sardinilla, Panama. The opacity of the tree canopy was derived from incoming brightness temperatures received on the ground. A collocated eddy-covariance flux tower measured water vapor fluxes and meteorological variables above the canopy. In addition, xylem sapflow of trees was measured within the flux tower footprint. We observed considerable diurnal differences between measured canopy opacities and modeled theoretical opacities that were closely linked to xylem sapflow. It is speculated that dielectric changes in the leaves induced by the sapflow are causing the observed diurnal changes. In addition, canopy intercepted rain and dew formation also modulated the diurnal opacity cycle. With an enhanced canopy opacity model accounting for water deposited on the leaves, we quantified the influence of canopy stored water (i.e. intercepted water and dew) on the opacity. A time series of dew formation and rain interception was directly monitored during a period of two weeks. We found that during light rainfall up to 60% of the rain amount is intercepted by the canopy whereas during periods of intense rainfall only 4% were intercepted. On average, 0.17 mm of dew was formed during the night. Dew evaporation contributed 5% to the total water vapor flux measured above the canopy.     

Global Structure Optimization of Quadrilateral Meshes

We introduce a fully automatic algorithm which optimizes the high‐level structure of a given quadrilateral mesh to achieve a coarser quadrangular base complex. Such a topological optimization is highly desirable, since state‐of‐the‐art quadrangulation techniques lead to meshes which have an appropriate singularity distribution and an anisotropic element alignment, but usually they are still far away from the high‐level structure which is typical for carefully designed meshes manually created by specialists and used e.g. in animation or simulation. In this paper we show that the quality of the high‐level structure is negatively affected by helical configurations within the quadrilateral mesh. Consequently we present an algorithm which detects helices and is able to remove most of them by applying a novel grid preserving simplification operator (GP‐operator) which is guaranteed to maintain an all‐quadrilateral mesh. Additionally it preserves the given singularity distribution and in particular does not introduce new singularities. For each helix we construct a directed graph in which cycles through the start vertex encode operations to remove the corresponding helix. Therefore a simple graph search algorithm can be performed iteratively to remove as many helices as possible and thus improve the high‐level structure in a greedy fashion. We demonstrate the usefulness of our automatic structure optimization technique by showing several examples with varying complexity.     

Multi-Modal Dialog Scene Detection Using Hidden Markov Models for Content-Based Multimedia Indexing

A class of audio-visual data (fiction entertainment: movies, TV series) is segmented into scenes, which contain dialogs, using a novel hidden Markov model-based (HMM) method. Each shot is classified using both audio track (via classification of speech, silence and music) and visual content (face and location information). The result of this shot-based classification is an audio-visual token to be used by the HMM state diagram to achieve scene analysis. After simulations with circular and left-to-right HMM topologies, it is observed that both are performing very good with multi-modal inputs. Moreover, for circular topology, the comparisons between different training and observation sets show that audio and face information together gives the most consistent results among different observation sets.     

Resampling Feature and Blend Regions in Polygonal Meshes for Surface Anti-Aliasing

Efficient surface reconstruction and reverse engineering techniques are usually based on a polygonal mesh representation of the geometry: the resulting models emerge from piecewise linear interpolation of a set of sample points. The quality of the reconstruction not only depends on the number and density of the sample points but also on their alignment to sharp and rounded features of the original geometry. Bad alignment can lead to severe alias artifacts. In this paper we present a sampling pattern for feature and blend regions which minimizes these alias errors. We show how to improve the quality of a given polygonal mesh model by resampling its feature and blend regions within an interactive framework. We further demonstrate sophisticated modeling operations that can be implemented based on this resampling technique.     

Specific heat capacity of molybdenum chalcogenides. III. Measurements of the heat capacity of Sn1 − x Ga x Mo5S6. An investigation of the singularities at low temperatures

The heat capacity of molybdenum chalcogenides with different Sn/Ga content was measured at temperatures of T 60 K. The occurrence of two phases of the chalcogenides studied could clearly be seen for higher Ga concentrations. In the miscibility gap there coexists a superconducting phase (T _c= 12.5 K) SnGa_0.25Mo₅S₆ with the ferromagnetic GaMo₅S₆ phase (T _curie = 19 K). As for the pure ternary compound GaMo₅S₆, a singularity of the heat capacity could also be observed in the range of the structural change (T = 45 K). All the singularities are discussed.     

Proximity electron tunneling spectroscopy. IV. Electron-phonon coupling and superconductivity of tantalum

An extensive superconducting electron tunneling study of Ta, using both a proximity method and an optimized conventional spectroscopy, is reported. The results for Ta confirm the electron-phonon origin of superconductivity in this element, and provide slightly improved superconducting parameters: =0.73 and _ph ^* = 0.11. The results from the PET and optimized conventional methods are in substantial agreement, although the proximity method appears to provide somewhat better resolution of structure in the Eliashberg function ² F(E).Operated for the U.S. Department of Energy by Iowa State University under contract No. W-7405-Eng-82. This research was supported by the Director for Energy Research, Office of Basic Energy Sciences, WPAS-KC-02-02-02.     

Charge exchange and the “Plateau” effect in YBa2Cu3O7?y

The superconducting properties of YBa₂Cu₃O_7- y, (YBCO) depend strongly on the oxygen content, whereas the transition temperatureT _cremains relatively constant for oxygen content between 6.8 and 7.0 (the Plateau effect) this effect has attracted considerable attention [see, e.g., D. de Fontaineet al., Nature (London) 343, 544 (1990); H. Paulsenet al., Nature (London) 349, 594 (1991); J. Jorgensen,Phys. Today 44, No. 6, 34 (1991)]. In this letter we introduce a microscopic theory of this phenomenon.     

A method to align the coordinate system of accelerometers to the axes of a human body: The depitch algorithm

One of the key problems in accelerometry based gait analyses is that it may not be possible to attach an accelerometer to the lower trunk so that its axes are perfectly aligned to the axes of the subject. In this paper we will present an algorithm that was designed to virtually align the axes of the accelerometer to the axes of the subject during walking sections. This algorithm is based on a physically reasonable approach and built for measurements in unsupervised settings, where the test persons are applying the sensors by themselves. For evaluation purposes we conducted a study with 6 healthy subjects and measured their gait with a manually aligned and a skewed accelerometer attached to the subject's lower trunk. After applying the algorithm the intra-axis correlation of both sensors was on average 0.89±0.1 with a mean absolute error of 0.05g. We concluded that the algorithm was able to adjust the skewed sensor node virtually to the coordinate system of the subject.     

Influence of particle elasticity in shear testers

Two dimensional simulations of non-cohesive granular matter in a biaxial shear tester are discussed. The effect of particle elasticity on the mechanical behavior is investigated using two complementary distinct element methods (DEM): Soft particle molecular dynamics simulations (Particle Flow Code, PFC) for elastic particles and contact dynamics simulations (CD) for the limit of perfectly rigid particles. As soon as the system dilates to form shear bands, it relaxes the elastic strains so that one finds the same stresses for rigid respectively elastic particles in steady state flow. The principal stresses in steady state flow are determined. They are proportional to each other, giving rise to an effective macroscopic friction coefficient which is about 10% smaller than the microscopic friction coefficient between the grains.