Physico-mechanical and degradation properties of biodegradable photografted coir fiber with acrylic monomers

Coir fibers were modified with 2-hydroxyethyl methacrylate (HEMA), methyl methacrylate (MMA) and 2-hydroxyethyl acrylate (2-HEA) solutions under UV radiation. Monomer concentration and radiation dose were optimized in terms of grafting and tensile properties. It was found that 20 % HEMA at 20th UV pass, 30 % MMA at 15th UV pass and 25 % 2-HEA at 20th UV pass of radiation produced higher tensile properties over untreated sample. Urea of different concentrations (0.5–2 %) were incorporated into optimized solutions and 1 % urea showed the best properties of the fiber. Water uptake behavior and simulating weathering degradation properties were also performed.     

Modification of Rheological Properties Under Elongational Flow by Addition of Polymeric Fine Fibers

A new technique to provide melt elasticity using flexible fine fibers prepared from a polymer with high melting point is demonstrated. A polymer composite of poly(propylene) with a small amount of fine fibers of poly(butylene terephthalate) shows marked strain‐hardening behavior in elongational viscosity, i.e., a rapid increase in the transient elongational viscosity with time or strain. The blend also shows prominent normal stress difference at steady shear. These elastic properties have not been observed for polymer composites with rigid fibers and can be applicable to the modification of rheological properties and thus the improvement of processability.

     

Farmer's view on soil organic matter depletion and its management in Bangladesh

Bangladesh is an agricultural country. About 80% of the total population live in rural areas. The contribution of agriculture to the gross domestic product is 30%. Rice is the major food crop while jute, sugarcane and tea are the main cash crops. Other important crops are wheat, tobacco, pulses, vegetables and fruits. Overall productivity in Bangladesh is stagnating or declining. The implication of yield stagnation or declining productivity is severe, since these trends have occurred despite rapid growth in the use of chemical fertilisers. Depletion of soil organic matter is the main cause of low productivity, which is considered one of the most serious threats to the sustainability of agriculture in Bangladesh. In Bangladesh, most soils have less than 17 g/kg and some soils have less than 10 g/kg organic matter. Farmers realise that there is a problem with soil fertility related to organic matter depletion. Farmers say that organic matter increases yield, reduces the production cost, improves crop growth and the economy, increases water-holding capacity and improves the soil structure. They recognise soil with higher organic matter content by darker brownish to black in colour. Some farmers are using fast-growing trees such as Flemingia macrophyla, Ipilipil (Leucaen leucophala), Glyricidia sepium, Boga Medula (Tephrosia candida), Dhol Kolmi (Ipomoea fistulosa), etc., as living fences, which can be used as fuel, fertiliser and fodder. To increase the soil organic matter, farmers use green manure crops, compost, quick compost, cow dung, azolla, etc. However, fuel for cooking purposes is limited and cow dung and crop residues are largely used as fuel. Crop residues are also used as fodder for livestock. Farmers expressed the wish to learn more about organic fertilizer management. However, sufficient food should be produced to keep pace with population growth. To alleviate the hunger and poverty is to increase the intensity of agricultural production and maintain favorable ecological conditions. Therefore, more organic matter should be used in the farmers' fields to sustain the soil fertility in an intensive farming system. This revised version was published online in June 2006 with corrections to the Cover Date.     

Prediction and sensitivity analysis of CNTs-modified asphalt’s adhesion force using a radial basis neural network model

Abstract

The expected longer service life of modified asphalt can be jeopardized by different environmental factors, such as moisture, oxidation, etc. which affect the desired properties by altering the adhesive property. An insight into knowledge of the adhesive property of the asphalt can help in providing more durable asphalt pavement. The study attempted to develop different models of adhesive properties of polymers and carbon nanotubes (CNTs) modified asphalt binders. The polymer-CNT modified asphalt is processed to prepare different types of samples, by simulating the damage due to moisture and oxidization, following the corresponding standard method. An Atomic Force Microscopy (AFM) was employed to assess the nanoscale adhesion force of the tested samples following the existing functional group in asphalt. Finally, the study has developed Radial Basis Function Neural Network (RBFNN) as a function of different parameters including; asphalt chemistry (i.e. AFM tip type and constant), type and percentages of polymers and CNTs and different environmental exposures (oxidation, moisture, etc.) to predict the nano adhesion force of asphalt. It is observed that the adhesive property of the Styrene–Butadiene modified asphalt is more consistent compared to the Styrene–Butadiene–Styrene modified asphalt, while the presence of Single-Wall Nanotubes (SWNT) is observed to affect the adhesive properties of asphalt significantly as compared to Multi-Wall Nanotubes (MWNT). The higher accuracy level of RBFNN model also indicates that the functional group (tip-type) adding with the percentages and types of polymers and CNTs significantly affect the adhesive properties of asphalt.     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

Reinforcement of graphene nanoplatelets on plasticized poly(lactic acid) nanocomposites: Mechanical,thermal, morphology,and antibacterial properties

Plasticized poly(lactic acid) (PLA)‐based nanocomposites filled with graphene nanoplatelets (xGnP) and containing poly(ethylene glycol) (PEG) and epoxidized palm oil (EPO) with ratio 2 : 1 (2P : 1E) as hybrid plasticizer were prepared by melt blending method. The key objective is to take advantage of plasticization to increase the material ductility while preserving valuable stiffness, strength, and toughness via addition of xGnP. The tensile modulus of PLA/2P : 1E/0.1 wt % xGnP was substantially improved (30%) with strength and elasticity maintained, as compared to plasticized PLA. TGA analysis revealed that the xGnP was capable of acting as barrier to reduce thermal diffusion across the plasticized PLA matrix, and thus enhanced thermal stability of the plasticized PLA. Incorporation of xGnP also enhanced antimicrobial activity of nanocomposites toward Escherichia coli, Salmonella typhimurium, Staphylococcus aureus, and Listeria monocytogenes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41652.     

Synthesis and Biological Evaluation of Ferrocenylquinoline as a Potential Antileishmanial Agent

The emergence of resistance against antileishmanial drugs in current use necessitates the search for new classes of antileishmanial compounds. Herein we report the design, synthesis, and evaluation of a novel ferrocenylquinoline for activity against Leishmania donovani. 7‐Chloro‐N‐[2‐(1H‐5‐ferrocenyl‐1,2,3‐triazol‐1‐yl)ethyl]quinolin‐4‐amine ( 1 ) was generated by coupling an iron(II) ethynylferrocene species with 4‐(2‐ethylazido)amino‐7‐chloroquinoline using click chemistry. The synthesized compound 1 was tested for its antileishmanial activity using both promastigote and amastigote stages of L. donovani. Compound 1 showed promising anti‐promastigote activity, with an IC₅₀ value of 15.26 μM and no cytotoxicity toward host splenocytes. From the battery of tests conducted in this study, it appears that this compound induces parasite death by promoting oxidative stress and depolarizing the mitochondrial membrane potential, thereby triggering apoptosis. These results suggest that ferrocenylquinoline 1 is a suitable lead for the development of new antileishmanial drugs.     

An investigation of sound absorption coefficient on sisal fiber poly lactic acid bio‐composites

In this research, the mechanical, acoustical, thermal, morphological, and infrared spectral properties of untreated, heat and alkaline‐treated sisal fiber‐reinforced poly‐lactic‐acid bio‐composites were analyzed. The bio‐composite samples were fabricated using a hot press molding machine. The properties mentioned above were evaluated and compared with heat‐treated and alkaline‐treated sisal fibers. Composites with heat‐treated sisal fibers were found to exhibit the best mechanical properties. Thermo‐gravimetric analysis (TGA) was conducted to study the thermal degradation of the bio‐composite samples. It was discovered that the PLA‐sisal composites with optimal heat‐treated at 160°C and alkaline‐treated fibers possess good thermal stability as compared with untreated fiber. The results indicated that the composites prepared with 30wt % of sisal had the highest sound absorption as compared with other composites. Evidence of the successful reaction of sodium hydroxide and heat treatment of the sisal fibers was provided by the infrared spectrum and implied by decreased bands at certain wavenumbers. Observations based on scanning electron microscopy of the fracture surface of the composites showed the effect of alkaline and heat treatment on the fiber surface and improved fiber‐matrix adhesion. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42470.     

Aloe vera gel: a new thickening agent for pigment printing

An attempt was made to print cotton fabric with pigments using a new thickening agent based on Aloe vera gel in combination with sodium alginate. The results were compared with the standard conventional printing recipe containing synthetic thickener, and a favourable effect of Aloe vera introduction was achieved. The results show that the properties of the printed fabric (sharpness, colour yield, overall fastness properties, softness, and water vapour transmission) are dependent on the percentage of Aloe vera gel in the thickener combination, the concentration of printing auxiliaries, and the curing conditions. Optimal printing properties were achieved by using a printing paste containing 80% Aloe vera/20% sodium alginate (700 g kg^?1), pigment (50 g kg^?1), binder (145 g kg^?1), fixer (10 g kg^?1), and ammonium sulfate (5 g kg^?1), followed by drying at 85 °C for 5 min and curing at 150 °C for 3 min. The sample printed with the new recipe showed superior rubbing fastness and handle properties, with a slightly lower colour yield, when compared with the sample printed with synthetic thickener. Finally, economic issues arising from synthetic thickener substitution are highlighted.