The effect of error control coding in multichannel FSK coherentlightwave communication systems influenced by laser phase noise

It has been shown that coherent optical fiber receivers with a two-filter structure (TFS) consisting of a wide-band IF filter and a narrow-band postdetection filter are less susceptible to the influence of phase noise. However, the expanded IF bandwidth required to achieve optimum sensitivity performance is large, particularly in multichannel FSK systems. Forward error control coding can relax the laser linewidth requirement and improve receiver sensitivity. In this paper a multichannel asynchronous FSK scheme equipped with (31, k) Reed-Solomon codes is used to verify the coding benefit. A systematic error probability analysis is developed and a stable and accurate performance evaluation procedure is provided. The sensitivity penalties due to the combined phase noise and interchannel crosstalk for both coded and uncoded systems are calculated for comparison. The results show that the performance reduction due to phase noise can be largely alleviated by choosing a proper code rate and an optimum value of the expanded IF bandwidth     

Scattering center parameterization of wide-angle backscattered datausing adaptive Gaussian representation

We present a scattering center extraction algorithm to parameterize the backscattered data from complex targets collected over large angular apertures. This parameterization is based on a scattering center model of the target, but includes an aspect-dependent amplitude function for each scattering center. A two-dimensional (2-D) adaptive Gaussian representation (AGR) algorithm is used to extract the position and the amplitude function associated with each scattering center. The algorithm is tested with data generated by the Xpatch radar simulation code as well as chamber measurement data. The results show that a very good compression ratio can be achieved, resulting in a compact scattering center model of the target. Once such model is available, we can easily reconstruct range profiles and ISAR images at any aspect on the same plane with good accuracy     

Protect privacy of deep classification networks by exploiting their generative power

Machine Learning - Research showed that deep learning models are vulnerable to membership inference attacks, which aim to determine if an example is in the training set of the model. We propose a...     

A steel surface defect inspection approach towards smart industrial monitoring

Journal of Intelligent Manufacturing - With the advance in Industry 4.0, smart industrial monitoring has been proposed to timely discover faults and defects in industrial processes. Steel is widely...     

硝基联苯、氨基联苯及啶酰菌胺的高效液相色谱分析方法

建立了一种高效液相色谱定量方法,测定以4-氯-2'-硝基联苯制备4-氯-2'-氨基联苯合成啶酰菌胺路线各步反应中的有效成分含量.采用InertSustain ODS-C18不锈钢柱(250 mm×4.6 mm i.d.×5μm)和二极管阵列检测器,以乙腈和0.02％磷酸水为流动相,流速为1.0 mL/min,在220 nm波长下对中间体4-氯-2'-硝基联苯进行分离和定量分析;在254 nm波长下对中间体4-氯-2'-氨基联苯进行分离和定量分析;在254 nm波长下对啶酰菌胺进行分离和定量.分析结果表明,4-氯-2'-硝基联苯保留时间约24.3 min,线性相关系数为1.0000,标准偏差为0.04,变异系数为0.34％,平均回收率为100.04％;4-氯-2'-氨基联苯保留时间约18.0 min,线性相关系数为1.0000,标准偏差为0.05,变异系数为0.33％,平均回收率为99.94％;啶酰菌胺保留时间约11.9 min,线性相关系数为1.0000,标准偏差为0.21,变异系数为0.32％,平均回收率为100.09％.方法 操作简便,精密度与准确度较高,满足定量分析要求.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

国产气相聚乙烯浆液催化剂的工业应用

本文简要阐述了北化院BCS01和上海院SLC-S两种国产气相聚乙烯浆液催化剂的性能、催化剂结构,在Unipol聚乙烯工业装置上应用结果,以及和进口同类催化剂UCAT-J的性能比较。     

Fabricating Water-Insoluble Polyelectrolyte into Multilayers with Layer-by-layer Self-assembly

Summary A water insoluble azo-containing polyelectrolyte (PEAPB6P-AC) was successfully fabricated into multilayer films based on the layer-by-layer adsorption technique by using N, N-dimethylformamide (DMF) as the assembling media. The multilayer growth and structure were studied with UV-vis spectroscopy, and the multilayer surface were imaged with Atomic Force Microscopy and compared with that fabricated in water. The results show that assembling PEAPB6P-AC in DMF can effectively eliminate the hydrophobic aggregation of the azo units and consequently results in a much smoother multilayer surface than that fabricated in water. This improvement to the layer-by-layer adsorption technique, which can avoid some major difficulties faced when assembling hydrophobic polyelectrolytes in aqueous solutions, seems to be a versatile way to fabricate high quality multilayer films when using the hydrophobic even water-insoluble polyelectrolytes as assembling units.     

Studies on membrane formation mechanism by the light transmission technique. I

New parameters, light transmission rate and minimum light transmissions, are proposed. These two parameters reflect the characteristics of the membrane‐forming system and the formation process of the membranes by phase inversion. The relationship between the light transmission and the porous structure of the membrane can be explained by the geometrical optics principles. Variation of the two parameters combining Reuvers's phase separation theory provided a convenient analytical method to predict effectively membrane morphologies. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 174–181, 2003     

Fabrication and amplification of Rhodamine B‐doped step‐index polymer optical fiber

A step‐index polymer optical fiber (SI POF) containing Rhodamine B in poly(methyl methacrylate) (PMMA) has been fabricated by a preform technique. Fluorescence of different fiber lengths were observed and discussed. A high gain (23 dB) for a SI POF with 60‐cm length, 400‐μm diameter was obtained. The Rhodamine B content of the doped SI POF is 5 ppm‐wt. The signal wavelength providing the highest gain for a 60 cm SI POF is around 630 nm, and the optimum fiber length is about 60 cm at 10 kW launched pump power. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 681–685, 2004