用瞬态频率波动法诊断齿轮故障

利用瞬态频率波动法实现频率调制信号的解调，提取齿轮的局部裂纹信息，并通过黄河ＴＮ２５２型汽车变速器疲劳试验的信号分析来验证。     

Preliminary Study on Aluminium-based Nanophase Composites Al_(88)Ni_(10)Y_2 and Al_(88)Ni_8Y_4

A new kind of aluminium-based alloy part amorphous/part crystalline, can be produced directlyby rapid quenching of the liquid. These materials have a novel structure of nanometer-sizedcrystals in an amorphous matrix and quite remarkable mechanical properties. The materialscan be considered to be nanophase composites. In this work Al88Ni10Y2 and Al88Ni8Y4 (atpct) nanophase composites consisting of a nanoscale dispersion of fcc-Al crystallites uniformlydispersed in an amorphous matrix, have been produced by melt-spinning. They have much highermicrohardness HV than fully amorphous alloys with the same composition. while retaining goodbending ductility The volume fraction, crystallite size and distribution of the fcc-Al phase havebeen estimated by DSC. X-ray diffraction and TEM. lt is found that the microstructure andproperties of the nanophase composites are very sensitive to the composition and the quenchingconditions. lncreasing the Y contedt and decreasing the Ni content at a given Al content givesmuch smaller dispersed nanophase aluminium crystallites. The volume fraction and crystallitesize of the fcc-Al phase increase with a decrease of wheel speed (quenching rate). The effectsof Y and Ni contents on the ease of formaticn of the nanophase composites are discussed. Theorigins of the novel mechanical properties are also considered.     

I．O．T．旧梦成真

该文较详细地介绍了Ｉ．Ｏ．Ｔ管的发展历程，其特点及工作方式。     

Silicon doped carbon/Cu joints based on amorphous alloy brazing for first wall application

Amorphous ribbon-type filler-metals represent a promising selection for joining heterogeneous materials together. In this work, rapidly solidified ribbon-type Ti based amorphous filler with a melting temperature of 850 °C and a thickness up to 20 μm is used to join silicon doped carbon to pure copper. SEM examinations demonstrate that a high quality brazed joints could be acquired. The brazed seam has a uniform structure and pore free along its entire length. TiC and ZrC are formed near the interface of carbon and filler-metal when the brazing holds enough time. Using very thin Mo and Cu foil (0.2 mm in thickness) as multiple interlayer are very effective to mitigate the thermal stress occurred in the interface between carbon and copper. The shear strength of this carbon-multiple interlayer-copper joint is more than 20 MPa, and the rupture is mainly occurred on the carbon side.     

Monolithic Catalysts with Low Noble-Metal Content for Exhaust Purification of Small Gasoline Engines

A series of low noble-metal coment monolithic catalysts for exhaust purification of small gasoline engines was investigated, and it was found that the Pt/Rh-OSM/Al2O3 （where OSM was oxygen storage material） catalyst with Ce0.5Zr0.5-MnOx（3%MnOx） OSM held low light-off temperature for CO, HC, and NO; quite wide three-way window, and outstanding thermal stability. The catalyst could efficiently comrol exhaust emission of small gasoline engines.     

A method for designing high-power offset Cassegrain antennas

Starting from the geometrical parameters of the feed and the desired gain of the Cassegrain antenna, a method to determine the design starting parameters for a high-power offset Cassegrain antennas is discussed. Then, by numerically solving the equations governing the antenna geometry, a set of design curves are obtained, with which the structure of the antenna can be determined by trading off the electrical and geometrical system requirements. The method presented can be applied to both high or low gain feeds for constructing a high power microwave electromagnetic environment, where complex electronic systems can be tested. For linearly polarized feeds with high gain, the structure parameters of antenna with zero cross polarization can be obtained, which is equal to the design results of Brown and Prata (see IEEE Trans. Antennas Propagat., vol.42, no.8, p.1145-53, 1994)     

一种彩色C型显示及数据处理终端

本文介绍了一种利用数字信号处理器ＴＭＳ３２０Ｃ２５用作雷达数据实时处理，利用图形处理器ＴＭＳ３４０１０用作雷达视频图象处理，完成雷达视频图象彩色显示的雷达终端。     

凸轮的表面裂纹分析

本文对一凸轮的表面裂纹进行了分析。渗碳后表层残余奥氏体含量过高级网状碳化物导致该凸轮在精磨过程中出现了磨削裂纹，本文还提出了二次回火或冰冷处理等改进措施来防止磨削裂纹的产生。     

雷弹射击效力的研究

雷弹是一种对付装甲目标群的新弹种,具有雷和弹的双重性能.用火炮或火箭炮发射雷弹时,评定其射击效力的方法目前是用计算机模拟,该文通过分析和推导,得出了评定雷弹射击效力的解析式.     

Osteogenesis of electrically stimulated bone cells mediated in part by calcium ions

Culture selected and expanded osteoblastic cells may be able to be reintroduced into massive skeletal defects to accelerate cell mediated regeneration of skeletal tissues, especially in bone ingrowth in total joint replacement, fracture healing, and osteoporosis. In vitro osteogenic cell culture is a useful model in studying the mechanism of bone metabolism under direct current stimulation. In this study, an osteoblastlike cell line was isolated from newborn rat calvaria. The osteogenic processes of the in vitro cultured cell line were studied by cytochemical, electron microscopic, and energy dispersive x-ray analysis techniques that resembled those observed in membrane bone ossification centers in vivo. Direct current stimulation of 100 microA/cm2 accelerated greatly the proliferation and calcification of the in vitro cultured cells. Intracellular free calcium ion metabolism was measured with an Adherent Cell Analysis and Sorting Machine. Under direct current stimulation, intracellular free calcium ion concentration increased an average of 2.3 times of the original level, which may play a key role in regulating osteogenesis and bone metabolism.