Tensile properties and morphology of S2Cl2 treated PVC-g-butly rubber

Summary We have grafted butyl rubber from PVC under a variety of conditions. The physical-mechanical properties of these graft copolymers have been examined both before and after extraction with hexane of the ungrafted butyl rubber. We have found a significant increase in the tensile strength of these materials upon S₂Cl₂ treatment (curing) in THF solution. This increase was observed even with unextracted copolymers. Electron micrograph studies suggest that curing causes an aggregation of the butyl rubber segments into crosslinked domains.     

Limits of compensation in a failed antenna array

In large antenna arrays, the possibility of occurrence of faults in some of the radiating elements cannot be precluded at all times. In such situations, the radiation pattern of the array gets distorted, mostly with an increase in sidelobe level and decrease in gain. Although it is not possible to restore the pattern fully by rearranging the excitations of the functioning elements, compensation methods have been reported in the literature for restoring one performance parameter of the array and making a trade‐off on some other parameter. In this article, we have made a study on the tolerance level of this compensation process. One part of the study deals with the thinning in the failed array, that is, to find a limit on the minimum number of functioning elements of the array that can restore the digital beamforming of the failed array. The second part of study deals with finding the maximum number of element failures that can be compensated. The study was carried out by optimizing the amplitude excitations of the failed array. Instead of classical optimization techniques, particle swarm optimization was used for the compensation process. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:635–645, 2014.     

Targeting and design of water networks for fixed flowrate and fixed contaminant load operations

Water-using processes are typically modeled as either fixed flowrate operations or fixed contaminant load operations. A new method for targeting the minimum freshwater and pinch in a single-contaminant water network is proposed, which can be applied to both kinds of operations. The method consists of plotting separate source and demand composites with flowrate as the horizontal axis and contaminant load unusually as the vertical axis. It is elegant, non-iterative, and can handle hybrid problems where both kinds of operations coexist.To design minimum freshwater networks for fixed flowrate problems, an algorithm is presented based on a newly developed principle of nearest neighbors. The principle simply states that the source streams to be chosen to satisfy a particular water demand must be the nearest available neighbors in terms of contaminant concentration.To design minimum freshwater networks for fixed contaminant load problems, the nearest neighbors algorithm is applied to process units that lie across the pinch. Units that lie entirely on one side of the pinch are satisfied by the cleanest source available on that side of the pinch. In other words, below-pinch units are satisfied by freshwater and above-pinch units are satisfied by the cleanest available stream above the pinch. Designs based on this methodology, apart from meeting the minimum freshwater target, also minimize the water flowing through the process units resulting in reduced network capital cost.     

Performance evaluation of saponin over other organic acid and tap water for removal of chromium in tannery sludge by electrokinetic enhancement

The performance of Saponin over different electrolyte-mediated electrokinetic (EK) process for removal of Cr(III) from tannery sludge was assessed. Saponin exhibited maximum Cr(III) removal efficiency, i.e. 67.6–80.75% as compared to other groups of processing fluids. The possible mechanistic approach for the highest removal efficiency of saponin over other electrolytes may be attributed to synchronized effect of micelle formation and subsequent complexation and sorption of chromium ions. The highest electroosmotic flow rate of saponin indicated low electroosmotic resistance during EK process, which validates the observed trend. Therefore, saponin can be considered as a promising electrolyte for EK treatment of tannery sludge.

Abbreviation: CA: Citric acid; LA: lactic acid; OA: oxalic acid; BOD: biochemical oxygen demand; COD: chemical oxygen demand; EK: electokinetic.     

Mass transfer between solid particles and liquid in a three phase fluidized bed

Particle-liquid mass transfer in a co-current three-phase fluidized bed of glass beads, water and air was studied with two measurement techniques. Both techniques measured the weight loss of a few particles coated with benzoic acid in a bed of inert glass beads. The effects of liquid and gas velocities, gas distribution and surface active agents on particle-liquid mass transfer in a three-phase fluidized bed were thus determined. In the absence of surface active agents in the liquid, particle-liquid mass transfer rates in a three-phase fluidized bed were up to 30% higher than in the corresponding liquid fluidized bed. When surface active agents were added to the liquid, the particle-liquid mass transfer rate was increased by up to about 100% in the three-phase fluidized bed, relative to the liquid fluidized bed. The particle-liquid mass transfer coefficient was found to be inversely proportional to the liquid hold-up in the three-phase fluidized bed.     

Direct contact heat transfer between two immiscible liquids during vaporization: Part II: Total evaporation time

A dilatometric technique was used to determine the total evaporation time of individual drops of furan, isopentane and cyclopentane as they rose in water. The values of total evaporation time were predicted reasonably well for each system by a different equation than was used to correlate the evaporative data for the initial 10% of the evaporative process as reported in Part I of this study. The total evaporation time data were also compared with the correlations given by Klipstein ⁽¹⁾, by Sideman and Taitel ⁽²⁾ and with the correlation which was found by the authors to best fit the total evaporative data for the three systems. In agreement with Klipstein ⁽¹⁾, the correlation for the overall heat transfer coefficient was found to be one of the form, q_A = Cd₁^2.0δt. The rate of rise of an evaporating drop for the conditions used in this study was found to be nearly equal to the instantaneous terminal velocity.     

Modal analysis of prestressed draft pad of freight wagons using finite element method

The present work intends to investigate dynamic behaviour of draft gear using finite element method. The longitudinal force that the draft gear absorbs usually leads to the failure of its components, especially, the load bearing draft pads. Dynamic behaviour of an individual draft pad and a draft gear is determined and characterized with exciting frequencies and corresponding mode shapes. The effect of compressive prestress load on the dynamic behaviour of an individual draft pad is also determined as the draft pads in assembled state are under constant axial compressive force in the draft gear. The vibration characteristics of individual draft pad are compared with draft pads that are part of draft gear. The modal analysis gives us a basis for subjecting a draft pad to higher frequency loading for determining its fatigue behaviour.

     

Comparative characteristic and erosion behavior of NiCr coatings deposited by various high-velocity oxyfuel spray processes

The purpose of this study is to analyze and compare the mechanical properties and microstructure details at the interface of high-velocity oxyfuel (HVOF)-sprayed NiCr-coated boiler tube steels, namely ASTM-SA-210 grade A1, ASTM-SA213-T-11, and ASTM-SA213-T-22. Coatings were developed by two different techniques, and in these techniques liquefied petroleum gas was used as the fuel gas. First, the coatings were characterized by metallographic, scanning electron microscopy/energy-dispersive x-ray analysis, x-ray diffraction, surface roughness, and microhardness, and then were subjected to erosion testing. An attempt has been made to describe the transformations taking place during thermal spraying. It is concluded that the HVOF wire spraying process offers a technically viable and cost-effective alternative to HVOF powder spraying process for applications in an energy generation power plant with a point view of life enhancement and to minimize the tube failures because it gives a coating having better resistance to erosion.     

Bacteria foraging optimization in antenna engineering: An application to array fault finding

Finding fault elements in linear antenna arrays using bacteria foraging optimization (BFO) is presented. One of the better options of array diagnosis is to perform it by measuring the radiated field, because in this case, removal of the array from its working site is not required and thereby not interrupting its normal operation. This task of fault finding from far‐field data is designed as an optimization problem where the difference between the far‐field power pattern obtained for a given configuration of failed element(s) and the measured one is minimized w. r. t. the excitations of the array elements. This set of excitations on comparison with the excitations of the original array gives the idea of the fault position and their type, such as either complete fault or partial fault. BFO being relatively new to microwave community when compared with other soft‐computing techniques, its performance was observed w. r. t. time of computation and convergence of the iterative process. Possibility of finding the faults from random sample points and use of minimum number of sample points for array fault finding are the novelties of the present work. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.