六铝酸钙材料的合成及其显微结构研究

分别采用轻质碳酸钙和活性氧化铝 ,或纯铝酸钙水泥和活性氧化铝为初始原料 ,反应烧结合成了六铝酸钙 (CA6)材料 ,研究了原料和成型压力对合成材料的烧结性能和显微结构的影响 ,同时借助于XRD、TG -DSC、SEM和EDAX等测试手段对其反应过程、物相变化和显微结构进行了分析和观察。研究结果表明 :(1) 130 0℃时 ,合成材料的主晶相为刚玉相和CA2 ,并开始有CA6形成 ;温度升至14 0 0℃ ,CA6大量生成 ;15 0 0℃时反应完成 ,产物全部为CA6相。 130 0～ 15 0 0℃时 ,上述反应表现为体积膨胀过程 ,试样的体积密度和径向线收缩率随温度的变化不大 ;而高于 15 0 0℃时 ,试样明显趋向烧结 ,体积密度升高 ,线收缩率加大。采用纯铝酸钙水泥和活性氧化铝合成的试样的体积密度均高于采用轻质CaCO3 和活性氧化铝的 ,尤其在烧成温度高于 15 0 0℃时。坯体的成型压力对这两种合成试样的烧结性能均没有显著影响。 (2 )合成六铝酸钙材料的晶粒形貌与合成工艺有关 ,制备片状晶粒的六铝酸钙材料需满足两个条件 :一是晶核有足够的发育空间 ,二是从晶核生长形成片状结构需足够的物质扩散。采用纯铝酸钙水泥和活性氧化铝为原料的试样 ,其CA6晶核很容易发育成片状晶形 ,且随着坯体成型压力的增加 ,片状CA6有向等轴状发展的趋势 ;采用     

微粉对矾土基超低水泥浇注料性能的影响

以高铝矾土熟料为主原料 ,加入 2 %的铝酸钙水泥及总量为 6 %的Al2 O3 微粉和SiO2 微粉 ,配制了矾土基超低水泥浇注料 ,研究了微粉对浇注料的烧结性能、力学性能及热震稳定性的影响。结果表明 :(1 )SiO2 微粉对浇注料的促烧结作用优于Al2 O3 微粉。这是因为与Al2 O3 微粉相比 ,由气相沉积生成的SiO2微粉的粒度小 ,比表面积大 ,活性较高。 (2 )随着SiO2微粉加入量的增加 ,在 1 1 0 0℃和 1 4 0 0℃处理后的常温强度以及在 1 30 0℃和 1 4 0 0℃下的高温抗折强度和抗热震性明显提高。这是由于引入的SiO2 微粉在高温下与Al2 O3 反应生成的针状莫来石穿插进入刚玉骨架 ,起着明显的强化和韧化作用     

新型植物杀菌剂--苯并噻二唑类植物抗病诱导剂

植物抗病诱导剂是近年来发现的一种新型植物杀菌剂，苯并噻二唑类(BTH)就是其中重要的一类。对近年来BTH研究情况作一简要综述。     

高岭土在碳热还原氮化过程中的相变

系统研究了苏州高岭土碳热还原氮化合成SiAlON过程在不同温度下的相变。对试样的XRD、SEM以及EDXA分析结果表明 ,1 30 0℃之前 ,试样中没有氮化物生成 ,物相为莫来石、石英和方石英 ;1 30 0℃时 ,高岭土开始发生氮化反应 ,生成过渡型SiAlON和β SiAlON。此时 ,石英和方石英相基本消失 ;1 4 0 0℃时 ,过渡型SiAlON、β SiAlON和X SiAlON三相共存 ,β SiAlON有所增多并有少量刚玉相生成 ;从 1 4 50℃到 1 550℃ ,Z值为 3的β SiAlON成为惟一的氮化产物 ,与少量SiC和刚玉相并存。莫来石在 1 50 0℃时完全消失     

用瞬时法测定液体导热系数

以珠状热敏电阻为加热元件,建立了用瞬时法测定液体导热系数的装置,在25℃下用乙二醇等7个标准样品,对该装置进行了标定,平均偏差为2%.为了核实装置和所得关系式的可靠性,又测定了13个已知导热系数的样品,多数偏差在2%以内,最大偏差为5%.单次测量的精度为0.2%.本文叙述了这一方法的原理,并对实验结果进行了讨论.     

应用免疫斑点法检测不同工艺灭活的乙肝血源疫苗中的前S_1和S_2蛋白

作者应用前 S_1、前 S_2和 HBsAg/a 单克隆抗体,用免疫斑点法(Immuno-spot)检测同一批的乙肝表面抗原分别经加热灭活和三步化学灭活后的前 S_1和前 S_2蛋白保留情况,比较了两种工艺对前 S_1和前 S_2蛋白的影响。结果表明;加热灭活可保留前 S_1和前 S_2蛋白,三步化学灭活使前 S_1和前 S_2蛋白丢失,从抗原组成上看,加热灭活后的抗原更接近自然抗原。首次报告了含有前 S_1蛋白的乙肝疫苗,并对前 S_1和前 S_2蛋白在乙肝血源疫苗中的可能作用进行了讨论。     

Analysis of junction temperatures in high-power GaN-based LEDs

We presented the analysis of the incomplete conduction in bonding medium in high power GaN-based light-emitting diode (LED) packages. A numerical study was carried out with parametric model to understand the junction temperature variation due to bonding medium defects. Transient thermal measurement was performed to evaluate LED’s junction temperature. Thermal resistance from chip to lead frame was 20 K/W in our sample LED. It was suggested that only 60% of the surface area of the bonding medium was involved...     

Preparation of micro-patterned surfaces of Si-N-O films and their influence on adhesion behavior of endothelial cells

Microgrooves were prepared on Si(100) surface by photolithography and wet etching.Subsequently,Si-N-O films were deposited on the microgrooves by unbalanced magnetron sputtering(UBMS) and micro-patterned surfaces of Si-N-O films were obtained.The size of the micropatterns was measured by surface profilometer.The chemical composition of Si-N-O films were characterized by X-ray photoelectron spectrometry(XPS) and the wettability of the micropatterned surfaces was evaluated by contact angle measurement.The beh...     

A novel shaft-less double suction mini pump

A novel double suction shaft-less mini pump was developed for heat control of small energy systems in this study.The mini pump impeller with an exit diameter of 40 mm was combined with the motor rotor supported by the hybrid dynamic bearing.The specific speed of the pump was 125 min-1 m3 min-1 m.The hydraulic performance of the pump was investigated experimen-tally under four rotational speeds.From the test results,it was recognized that the pump could provide a flow discharge of 5 L/min and head of 1.5 m,w...     

Fuel combustion test in constant volume combustion chamber with built-in adaptor

Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hol...