回转体零件的CAPP专家系统研究

提出了一种基于规则的CAPP专家系统。系统针对回转体零件 ,选择产生式知识表达方法 ;并且根据正向推理的决策机制 ,提出了工艺路线的决策规则和相应的算法。在此基础上 ,建立了系统模型和简单的数据库     

AN EXTENDED MODELING OF TIDE-WAVE MOTION

1 .　ＩＮＴＲＯＤＵＣＴＩＯＮＴｏｓｔｕｄｙｔｈｅｍｏｔｉｏｎｏｆｔｈｅｔｉｄｅ ｗａｖｅｓ,ｔｈｅｓｈａｌｌｏｗｗａｔｅｒｅｑｕａｔｉｏｎｓ ,ｉ.ｅ .ｔｈｅｖｅｒｔｉｃａｌｉｎｔｅｒｇｒａ ｔｉｏｎｏｆｔｈｅｃｏｎｔｉｎｕｉｔｙｅｑｕａｔｉｏｎａｎｄｍｏｍｅｎｔｕｍｅｑｕａ ｔｉｏｎ ,ｉｓｃｏｎｓｉｄｅｒｅｄａｓｔｈｅｇｏｖｅｒｎｉｎｇｅｑｕａｔｉｏｎｓ.Ｂｙａｂｏｖｅｅｑｕａｔｉｏｎｓｔｗｏｅｑｕａｔｉｏｎｓｒｅｌａｔｅｄｔｏｔｈｅｈｏｒｉｚｏｎ ｔａｌｆｌｕｘｏｆｔｈｅｔｉｄｅ ｃｕｒｒｅｎｔｓａ…     

一种智能化的键盘练习器

本文介绍了一个利用单片机研制的键盘操作练习器。它能完成健盘输入练习和输入水平测试二项功能。     

A numerical investigation on the geometry dependence of the crack growth resistance in CT specimens

The influence of the specimen thickness B and the ligament length b on the J _R -curves is numerically investigated for CT specimens. The thickness effect is taken into account with 2-D analyses by dividing a plain sided specimen into a plane stress part and a plane strain part. The fracture process is controlled by experimentally determined critical values of the crack tip opening displacement for crack growth initiation (CTOD_i) and the crack tip opening angle for stable crack growth (CTOA_C). It is shown that for the global behaviour of a plain sided specimen, the B/b ratio is essential. The difference between the geometry dependence of the initiation value of the J-integral and the geometry dependence of the slope of the J _R -curves is also shown.     

Instability due to Viscosity Stratification Downstream of a Centerline Injector

A common injector geometry upstream of a static mixer is the centerline injector. A flow instability can arise due to viscosity differences between the injected core‐flow and the outer co‐flow. This instability can adversely affect the effectiveness of the mixing operation. An experimental investigation of miscible viscosity‐stratified flow in a circular geometry was performed using Laser Induced Fluorescence (LIF) and Particle Image Velocimetry (PIV). The experimental results for the stable region agree with the analytical results. The unstable region exhibits different modes depending on the viscosity ratio, volume flux ratio, and Reynolds number. The modes include wavy core‐flow with fissures and wavy core‐flow with core breakup. The time‐averaged experiment velocity profiles for the unstable core indicate a broadening of the jet at the centerline, which is consistent with the LIF visualization.     

铜基催化剂孔隙率对气体有效扩散系数的影响

研究了18种具有不同孔结构参数的粒状铜基甲醇合成催化剂孔隙率对有效扩散系数的影响。结果发现，催化剂微孔孔隙率增大，曲节因子亦增大，扩散阻力增加。将孔隙率与催化剂曲节因子关联，得到了半经验方程，用它可估算催化剂的曲节因子。     

热声热机系统振荡频率的理论计算与实验验证

以热声发动机为例采用网络模型计算了热声热机系统的振荡频率，得出振荡频率为复频率，其实部代表实际频率，虚部表示压力幅值的衰减程度。对热机系统在各种不同的情况下(包括不同大小的谐振腔、板叠间距、气体静压、系统长度)进行了数值计算，理论计算值与实验结果能很好的吻合。     

自适应指纹预处理算法

基于大量的实验提出了一套行之有效的指纹处理算法，主要包括使用基于方向图的自适应旋转滤波器、与自适应增强滤波同时进行的自适应阀值边缘处理、自适应阀值二值化，很好地增强了指纹图像的清晰度，同时起到了很好的滤波作用，为可靠、准确地实现指纹自动识别系统奠定了最可靠的基础．     

A hexane solution deposition of SnS2 films from tetrabutyltin via a solvothermal route at moderate temperature

SnS₂ films have been deposited on glass and alumina plate substrates by the reactions between an organotin precursor [tetrabuyltin, (CH₂CH₂CH₂CH₃)₄Sn] and carbon disulfide in n-hexane at the temperature range 180-200 °C for 10-40 h. The reaction system was oxygen free and applied at a moderate temperature. The films so prepared were characterized by techniques of X-ray diffraction, Scanning electron microscopy, Raman and Mössbauer spectroscopies. The films deposited on glass as well as on alumina plate have an average thickness of 30 μm, but have different rose-like morphologies, which are influenced by both the anisotropic growths of crystals and the different substrate structures. Photoluminescence measurements show that the films have an emission peak at approximately 590 nm.