Torque calculation between circular coils with inclined axes in air

In this paper we derive new semi‐analytical expressions for calculating the electromagnetic torque between inclined circular coils in air. The torque calculation has been obtained from the corresponding mutual inductance between inclined circular coils using the filament method. The coils of rectangular cross‐section whose centers are at the same and the different axes have been considered. From this general case it is possible to calculate the torque between all possible coil combinations either with rectangular or neglected cross‐section. Results obtained by the presented approach are in very good agreement with already published data. This method can be used for industrial electromagnetic devices such as torque sensors, transducers and torque‐measuring devices. Copyright © 2010 John Wiley & Sons, Ltd.     

Substituted imino and amino derivatives of 4-hydroxycoumarins as novel antioxidant,antibacterial and antifungal agents: Synthesis and in vitro assessments

A series of imino and amino derivatives of 4-hydroxycoumarins were synthesised and evaluated for antioxidant potential, through different in vitro models such as (DPPH) free radical-scavenging activity, linoleic acid emulsion model system, reducing power assay and phosphomolybdenum method. Also, antimicrobial activity of obtained coumarins was evaluated against 13 bacteria and eight fungi. All prepared compounds possessed good antioxidant activity and among them a p-nitrophenol derivative with IC₅₀ at 25.9 μM possessed radical-scavenging activity which was comparable to BHT. Observed data for antibacterial activity indicated strong activity of all tested amino derivatives, while imines showed better antifungal properties.     

Improvement of the stoichiometric network analysis for determination of instability conditions of complex nonlinear reaction systems

Stoichiometric network analysis (SNA), a known method for analyzing complex reaction systems including biochemical ones, is improved and applied to a nonlinear process studied far from equilibrium in a continuously fed, well stirred tank reactor (CSTR). A particular attention is focused on the determination of the narrow range of the control parameter values where the main steady state is unstable and where different dynamic states can be simulated numerically. The instability region, the most important feature of nonlinear reaction systems, is calculated as a function of the SNA parameters (current rates and reciprocal concentrations of intermediate species in the steady state) and simplified by retaining only the dominant terms. Since the number of the current rates is usually larger than the number of linearly independent equations to be used for their calculation, it is shown here that the current rates can be replaced with a smaller number of reaction rates at the steady state. These rates are related to the experimental data in a simple manner. The instability condition is also written as a function of dimensionless parameters derived from the SNA. This general approach is applied to a model of the Bray–Liebhafsky (BL) reaction having seven reactions without direct autocatalysis or autoinhibition, studied under CSTR conditions. Since the model has six intermediate species, it would be very difficult to analyze its instability condition by the conventional procedure, where a sixth order characteristic equation would have to be solved. On the other hand, the instability condition, obtained easily by the improved SNA, locates correctly the oscillatory region using numerical integration. Other dynamic states found earlier with a larger model of the BL reaction, such as mixed-mode oscillations, period doubling and chaos, are also obtained within the theoretically predicted oscillatory region. Thus, besides the general advantages of the improved stoichiometric network analysis as a method appropriate for the examination of complex nonlinear reactions, we show that the various mentioned dynamic states can be obtained by a very simple variant of the model of the BL reaction realized under CSTR conditions.     

Aerodynamic design and analysis of a small-scale vertical axis wind turbine

Small-scale vertical axis wind turbines are regarded today as an attractive source of green energy, still insufficiently implemented and tested. This paper presents a fast design methodology of such a VAWT, in terms of choosing its main parameters: airfoil, rotor diameter and solidity. For obtaining generated power of each considered geometrical model at different undisturbed wind velocities and rotor angular velocities two models were used — momentum and vortex-wake model, combined with experimentally measured airfoil data (airfoil lift and drag coefficients). Even though the former model is simpler, it is the most utilized model, known to provide good results in stationary working regimes. Both models still present fairly accurate and fast tools for computation and optimization, particularly useful in the phase of conceptual design. In this research, the use of the momentum model resulted in determination of the maximal power coefficient, optimal- and minimal freestream velocity for every considered VAWT model. From these output parameters, a selection of the optimal geometric model was done, and a more detailed transient analysis and flow representation around the selected solution was obtained by the vortex-wake model. The results obtained by the two used computational models coincide satisfactorily.     

Wear Behavior of Composites Based on ZA-27 Alloy Reinforced by Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Particles Under Dry Sliding Condition

In present study, the effect of Al₂O₃ particle reinforcement on the sliding behavior of ZA-27 alloy composites was investigated. The composites with 3, 5, and 10 wt% of Al₂O₃ particles were produced by the compocasting procedure. Tribological properties of unreinforced alloy and composite were studied, using block-on-disk tribometer under unlubricated sliding conditions at different specific loads and sliding speeds. The worn surfaces of samples were examined by the scanning electron microscopy (SEM). The test results revealed that those composite specimens exhibited significantly lower wear rate than the ZA-27 matrix alloy specimens in all combinations of applied loads and sliding speeds. The difference in the wear resistance of composite with respect to the matrix alloy, increased with the increase of the applied load/sliding speed and Al₂O₃ particle content. The highest degree of improvement of the ZA-27 alloy tribological behavior corresponded with change of the Al₂O₃ particles content from 3 to 5 wt%. At low sliding speed, moderate lower wear rate of the composites over that of the matrix alloy was noticed. This has been attributed to micro cracking tendency of the composites. Significantly reduced wear rate, experienced by the composite over that of the matrix alloy at the higher sliding speeds and loads, could be explained due to enhanced compatibility of matrix alloy with dispersoid phase and greater thermal stability of the composite in view of the presence of the dispersoid. Level of wear rate of tested ZA-27/Al₂O₃ samples pointed to the process of mild wear, which was primarily controlled by the formation and destruction of mechanical mixed layers (MMLs).     

Influence of T4 Heat Treatment on Tribological Behavior of Za27 Alloy Under Lubricated Sliding Condition

The effects of heat treatment on the microstructure, hardness, tensile properties, and tribological behavior of ZA27 alloy were examined. The alloys were prepared by conventional melting and casting route. The heat treatment of samples included the heating up to 370 °C for 3 or 5 h, quenching in water, and natural aging. Lubricated sliding wear test were conducted on as-cast and heat-treated ZA27 samples using block-on-disc machine. The friction and wear behavior of alloys were tested in contact with steel discs using combinations of three levels of load (10, 30, and 50 N) and three levels of linear sliding speeds (0.26, 0.50, and 1.00 m/s). To determine the wear mechanisms, the worn surfaces of the samples were examined by scanning electron microscopy (SEM). The heat treatment resulted in reduction in the hardness and tensile strength but increase in elongation. The heat-treated alloy samples attained improved tribological behavior over the as-cast ones, under all combinations of sliding speeds and contact loads. The rate of improvement increased with duration of solutionizing process before quenching in water. Obtained tribological results were related to the effects of heat treatment on microstructure changes of alloy.     

A case study on the object-oriented framework for modeling product families with the dominant variation of the topology in the one-of-a-kind production

Traditional configuration-based product family modeling techniques do not yield favorable solutions for modeling the product families with the dominant product topology variations. This paper presents the case study for the modeling of variations of the product configuration, parameters, and topologies in mass production of custom windows and doors in a one-of-a-kind production (OKP) company. The case study is based on the object-oriented product family modeling framework we developed for OKP which is characterized by the dominant product variation by topology. The problem of variation in topology in our framework is solved by the manual model transformation in the computer-aided design module which creates a new metamodel of products with the desired topology and which is the basis for a further, automatic model transformation. Usage of our framework has a positive effect on the level of the product customizations and shortening of the leading time which helps OKP companies in obtaining a better position at the market. Our software solution for the designing and manufacturing of custom windows and doors based on our framework is implemented in more than 300 mostly small- and medium-sized enterprises. It proves our concept which can be used for the realization of the information systems for computer-aided one-of-a-kind production in the companies with a different production plan.     

Microstructural and Tribological Properties of A356 Al–Si Alloy Reinforced with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Particles

In the present study, the effect of the Al₂O₃ particles (average size of 12 μm, 3 and 10 wt.%) reinforcement on the microstructure and tribological properties of Al–Si alloy (A356) was investigated. Composites were produced by applying compocasting process. Tribological properties of unreinforced alloy and composites were studied, using pin-on-disc tribometer, under dry sliding conditions at different specific loads and sliding speed of 1 m/s. Microhardness measurements, optical microscope and scanning electron microscope were used for microstructural characterization and investigation of worn surfaces and wear debris. During compocasting of A356 alloy, a transformation from a typical dendritic primary α phase to a non-dendritic rosette-like structure occurred. Composites exhibited better wear resistance compared with unreinforced alloy. Presence of 3 wt.% Al₂O₃ particles in the composite material affected the wear resistance only at specific loads up to 1 MPa. The wear rate of composite with 10 wt.% Al₂O₃ particles was nearly two order of the magnitude lower than the wear rate of the matrix alloy. Dominant wear mechanism for all materials was adhesion, with others mechanisms: oxidation, abrasion and delamination as minor ones.     

Systems Theory for the civil engineer Experience with knowledge acquisition for an engineering expert system

Issues involved in the knowledge acquisition process for engineering applications of expert systems are discussed, with reference to a project underway in the reservoir management domain. Since there are no well established guidelines for the crucial task of acquiring human problem solving expertise, the individual responsible forthis task must rely on his own judgement and suggestions found in the literature. Based on the experience from this project, success in the area of knowledge acquisition appears to require the incremental development of very problem specific engineering expert systems, which facilitates the knowledge acquisition process. Other important factors described include the domain knowledge of the knowledge engineer (the person responsible for knowledge acquisition), the interaction between the expert and the knowledge engineer, and the expectations for the expert systems.