This forensic study is unique in that it involves a pavement warranty specification. Extensive field and laboratory testing was conducted to determine the cause(s) of longitudinal cracks observed on the surface. Four trenches were cut and removed to allow more testing on top of each pavement layer. The tests found that the stiffness of the foamed asphalt base is higher than that of a typical flexible base. However, the subgrade modulus is low compared with the average subgrade modulus in Texas. Water seeped into two trenches (dug into the road where there were surface cracks) within 20 min of digging. No water was observed in the other two trenches, where there were no surface cracks. The two trenches with surface cracks have lower base density and higher base moisture content than the two with no surface cracks. Based on observations of the trenching and coring operations, the same surface cracks have been detected in the base layer. Cracks up to 150 mm into the base layer have been observed. Although cracks have been observed in the base (and they can be related to lower stiffness and higher falling weight deflectometer deflections), it is difficult to determine if the cause of surface cracks is due to the base layer alone. It is difficult to prove if the layer is responsible for the failure, except by properties listed in the specification. One faulty pavement layer can easily cause the failure of other layers. For warranty purposes, layer-specific failure criteria should be clearly outlined. The base did not meet the gradation specification. The field material was substantially finer than specified. While some specifications may have been violated, there is little evidence to show that the cause of the longitudinal cracking is primarily related to the foamed-asphalt-stabilized base. 相似文献
The MHD Jeffery-Hamel flows in non-parallel walls are investigated analytically for strongly nonlinear ordinary differential equations using homotopy analysis method (HAM). Results for velocity profiles in divergent and convergent channels are presented for various values of Hartmann and Reynolds numbers. The convergence of the obtained series solutions is explicitly studied and a proper discussion is given for the obtained results. Comparison between HAM and numerical solutions showed excellent agreement. 相似文献
Ventricular septal defect (VSD) is one of the most common types of congenital heart defects (CHD). There are vivid multifactorial causes for VSD in which both genetic and environmental risk factors are consequential in the development of CHD. Methionine synthase reductase (MTRR) and methylenetetrahydrofolate reductase (MTHFR) are two of the key regulatory enzymes involved in the metabolic pathway of homocysteine. Genes involved in homocysteine/folate metabolism may play an important role in CHDs. In this study; we determined the association of A66G and C524T polymorphisms of the MTRR gene and C677T polymorphism of the MTHFR gene in Iranian VSD subjects. A total of 123 children with VSDs and 125 healthy children were included in this study. Genomic DNA was extracted from the buccal cells of all the subjects. The restriction fragment length polymorphism polymerase chain reaction (PCR-RFLP) method was carried out to amplify the A66G and C524T polymorphism of MTRR and C677T polymorphism of MTHFR genes digested with Hinf1, Xho1 and Nde1 enzymes, respectively. The genotype frequencies of CC, CT and TT of MTRR gene among the studied cases were 43.1%, 40.7% and 16.3%, respectively, compared to 52.8%, 43.2% and 4.0%, respectively among the controls. For the MTRR A66G gene polymorphism, the genotypes frequencies of AA, AG and GG among the cases were 33.3%, 43.9% and 22.8%, respectively, while the frequencies were 49.6%, 42.4% and 8.0%, respectively, among control subjects. The frequencies for CC and CT genotypes of the MTHFR gene were 51.2% and 48.8%, respectively, in VSD patients compared to 56.8% and 43.2% respectively, in control subjects. Apart from MTHFR C677T polymorphism, significant differences were noticed (p < 0.05) in C524T and A66G polymorphisms of the MTRR gene between cases and control subjects. 相似文献
In this paper we have presented a TOPSIS approach based on preference ratio and an efficient fuzzy distance measurement for a Fuzzy Multiple Criteria Group Decision-Making Problem (FMCGDMP). Preference ratio with a moderate modification for negative fuzzy numbers was used as an efficient ranking method for fuzzy numbers in a relative manner. As human reasoning persuades that distances between two fuzzy numbers should be a fuzzy measure, so all distances between fuzzy numbers (i.e. distances between alternatives, Fuzzy Positive Ideal solutions, and Fuzzy Negative Ideal solutions) have been calculated as fuzzy numbers using an efficient fuzzy distance measurement. The aforementioned arguments make the proposed algorithm unique and well posed for real-life problem modeling. Moreover, the main novelties of the proposed procedure (i.e. the fuzzy distance measurement and Preference Ratio) have been developed for Generalized Fuzzy Numbers (GFNs). The proposed algorithm has efficiently been applied in assessment of traffic police centers which is treated as a FMCGDMP. 相似文献
A new model with comprehensive kinetics for propylene homopolymerization in fluidized bed reactors was developed to investigate the effect of mixing, operating conditions, kinetic and hydrodynamic parameters on the reactor performance as well as polymer properties. Presence of the particles in the bubbles and the excess gas in the emulsion phase was considered to improve the two-phase model, thus, considering the polymerization reaction to take place in both the bubble and emulsion phases. It was shown that in the practical range of superficial gas velocity and catalyst feed rate, the ratio of produced polymer in the bubble phase to the total production rate is roughly between 10% and 13%, which is a substantial amount and cannot be ignored. Simulation studies were carried out to compare the results of the improved two-phase, conventional well-mixed and constant bubble size models. The improved two-phase and well mixed models predicted a narrower and safer window at the same running conditions compared with the constant bubble size model. The improved two-phase model showed close dynamic behavior to the conventional models at the beginning of polymerization, but starts to diverge with the evolution of time. 相似文献
We present an interactive, menu-driven software package which allows the design of three-dimensional structures from standardized component modules. The standardized component modules used as example building blocks in the project are rectangular solids of several sizes.
The system has been designed such that its output (i.e. the design database) can be used to automatically generate a robot motion program to assemble the designed structure.
Presented are the system database and its internal data structure, an object placement-sequencer algorithm, a height specification and interference checking algorithm, and a balance-checking algorithm. To avoid the creation of dynamic obstacles and interference of the robot arm with these obstacles, the proper sequencing of the blocks in the design database is essential. The object placement-sequencer algorithm is responsible for proper sequencing of the blocks in the design database to avoid the aforementioned problem. The height specification and interference checking algorithm automatically generates the proper positioning of a block in the design by performing a sequential search over the accumulated design structure. The stacking feasibility of the blocks in the design is verified by the balance-checking algorithm, prior to the acceptance of the block as a permanent part of the design. 相似文献
A novel electrochemical route is used to form highly {111}-oriented and size-controlled Au nanoprisms directly onto the electrodes of quartz crystal microbalances (QCMs) which are subsequently used as mercury vapor sensors. The Au nanoprism loaded QCM sensors exhibited excellent response-concentration linearity with a response enhancement of up to ~ 800% over a non-modified sensor at an operating temperature of 28?°C. The increased surface area and atomic-scale features (step/defect sites) introduced during the growth of nanoprisms are thought to play a significant role in enhancing the sensing properties of the Au nanoprisms toward Hg vapor. The sensors are shown to have excellent Hg sensing capabilities in the concentration range of 0.123-1.27 ppm(v) (1.02-10.55 mg m(-3)), with a detection limit of 2.4 ppb(v) (0.02 mg m(-3)) toward Hg vapor when operating at 28?°C, and 17 ppb(v) (0.15 mg m(-3)) at 89?°C, making them potentially useful for air monitoring applications or for monitoring the efficiency of Hg emission control systems in industries such as mining and waste incineration. The developed sensors exhibited excellent reversible behavior (sensor recovery) within 1 h periods, and crucially were also observed to have high selectivity toward Hg vapor in the presence of ethanol, ammonia and humidity, and excellent long-term stability over a 33 day operating period. 相似文献
In this study, the Geocoat™ technology was used for the extraction of zinc from a mineral concentrate obtained from the Kooshk mine (Yazd, Iran) by a culture dominated by the mesophilic bacterium Acidithiobacillusferrooxidans in a packed column bioreactor. A low grade sphalerite ore was used as support for the concentrate coating. During the 100 days of leaching pH, Fe3+, Fetotal, microbial population density and zinc extraction were measured. The final zinc extraction from concentrate and low grade support was 97% and 78%, respectively, and it was found that leaching from the support does not proceed significantly before leaching from the coating is completed. 相似文献
A comparison between the use of Fourier and Hartley transforms for motion estimation of multiple moving objects in image sequences is presented. The spectrum of the two transforms show that the temporal frequencies at the peaks (of the spectrum) is related to the velocity of the moving objects. The analysis shows that the Hartley technique is faster and requires less memory space than the Fourier technique. However, it gives the velocity of the moving objects but not the direction. The Fourier spectrum, on the other hand, gives the velocity and direction. An efficient implementation is possible by using the Hartley transform to estimate the temporal frequencies of the peaks and hence the velocities. The fast Fourier transform is then used to compute the spectrum at those peaks. The direction is easily found from the Fourier spectrum by reversing the sign of the temporal frequency corresponding to the peak. 相似文献