Feasibility analysis of phonon lasers

We identify the main reason impeding coherent generation of phonons in solid state - the inherently high density of phonon states. Based on the results of our analysis we formulate a set of conditions that may make phonon lasing practical and point out the most promising mechanism of phonon lasing: LO/spl rarr/LA+TO in InP. We then develop a complete set of phonon laser equations and evaluate the threshold, output power and efficiency of phonon lasers based on InP MESFET. We show that one can obtain high-power 1.26-THz coherent phonon emission with pump power as small as a few milliwatts and up to 5% slope efficiency. Potential applications are also discussed.     

组合结构体的控制爆破拆除

根据待拆构筑物的结构特点和周围环境，分析论述构件倒塌的可能性。因地制宜选择，制定出合理的爆破方案。并通过对爆破参数，起爆网络，安全防护等进行精心设计和施工，拆除爆破达到了预期的效果。     

TBM掘进隧洞回填固结灌浆施工的探讨

豆砾石回填灌浆和固结灌浆在引黄工程南干线长达90kmTBM施工中得到成功的应用。文中介绍了引黄工程南干线4^#-7^#隧洞豆砾石回填灌浆、特殊地质洞段的固结灌浆的灌浆设备、材料、浆液配比、压力、工艺等诸方面的现场施工情况。     

应用AR模型的IMU误差系数漂移预测研究

将影响IMU误差系数漂移并难于分离的多种因素综合为一种因素，假定IMU误差系数的漂移由一特定系统所引起，从而采用时间序列建模方法进行IMU误差系数漂移的预测。该方法具有消除各因素具体分析中的不确定性并减少其工作员的优点。文中描述了其原理，对某惯组的33个误差系数进行了时间序列建模与预测并得到有效的结果。最后还阐述了存在的问题及其解决方法。     

一种单片机控制的指令转换器的设计

采用89C51单片机，串口扩展芯片8251、中断扩展芯片8259等器件设计了一种指令格式转换器。     

布帮鞋无浆贴合工艺技术

本工艺是对原有工艺的改进，突破了原有布帮鞋不能采用无浆贴合的局限性，对原有工艺中的不足有了很大的改进，提高了生产效率，改善了鞋子外观质量，增加了鞋子的美观性。     

山区长输气管线的曲线测设

该文介绍了在山区长输气管线测量中 ,管线的折点桩之间大部分不通视且部分点上空有障碍物 ,采用GPS不能施测坐标时 ,结合山区的自然地理条件 ,采用全站仪间接施测折点水平角 ,极坐标法测设曲线以及跨越障碍物测设曲线的内容和方法 ,可在一定精度要求下应用     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

射频板条CO_2激光器并联谐振技术的研究

本文利用周期性网络模型计算了射频板条CO2激光器电极的纵向电压分布．探讨了并联谐振技术在板条器件中获得成功运用的原因．提出了利用并联谐振技术进一步提高电压分布均匀性的两个途径．     

HDPE／PS／HDPE－g－PS合金的相容性和力学性能研究

用自制接枝共聚物ＧＲ－Ⅰ、ＧＲ－Ⅱ相容剂研究其对ＨＤＰＥ／ＰＳ共混物相容性和力学性能的影响。通过ＳＥＭ、ＤＭＡ、ＤＳＣ和力学性能测试表征，表明在ＨＤＰＥ／ＰＳ共混中加入这些相容剂其相容性和力学性能有一定提高