Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Understanding silica-supported metal catalysts: Pd/silica as a case study

Supported metal catalysts, particularly noble metals supported on SiO₂, have attracted considerable attention due to the importance of the silica–metal interface in heterogeneous catalysis and in electronic device fabrication. Several important issues, e.g., the stability of the metal–oxide interface at working temperatures and pressures, are not well-understood. In this review, the present status of our understanding of the metal–silica interface is reviewed. Recent results of model studies in our laboratories on Pd/SiO₂/Mo(1 1 2) using LEED, AES and STM are reported. In this work, epitaxial, ultrathin, well-ordered SiO₂ films were grown on a Mo(1 1 2) substrate to circumvent complications that frequently arise from the silica–silicon interface present in silica thin films grown on silicon.     

Structure and electrical characteristics of Ce4+-doped Ba2In2O5

The In-site of Ba₂In₂O₅ with Brownmillerite structure was partially substituted for Ce⁴⁺ ions in order to examine the doping effect on the order-disorder transition. Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1, 0.2, 0.3, 0.5, 1.0, and 1.5) were prepared by solid state reaction. X-Ray diffraction analyses of these powder samples demonstrated that Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.1 and 0.2) possesses Brownmillerite structure. With increasing content of Ce⁴⁺ ion the crystal system of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.3, 0.5, and 1.0) changed to cubic perovskite structure above the order-disorder transition temperature of Ba₂In₂O₅. Arrhenius plots of the electrical conductivities of Ba₂In_{2 – x} Ce _x O_{5 + x/2} (x = 0.2, 0.3, and 1.0) exhibited no discontinuity. These compounds had high transference numbers of oxide ion above 973 k.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003