The geographic variation of cancer incidence in Ontario

OBJECTIVES: Our objectives were (1) to describe an analysis of the spatial pattern of cancer incidence in Ontario and (2) to discuss the quality of data in the Ontario Cancer Registry with respect to the accuracy of local cancer rates. METHODS: Cancer incidence rates were calculated for 22 cancer sites in 49 counties of Ontario during 1976 to 1986. Capture-recapture methods were used to estimate completeness of case registration, and completeness of residence information was also assessed. Spatial autocorrelation was used in measuring the geographic pattern of incidence rates. Comparisons were also made between sexes and with earlier data from 1966 to 1975. RESULTS: The quality of the geographic data in the registry appeared good, and corrections for incomplete or inaccurate registration had little impact. About one third of the sex-site combinations showed some evidence of spatial patterning in the cancer rate. Particularly strong regional variation was noted for cancers of the stomach, lung, uterus, and prostate. CONCLUSIONS: The analysis revealed a number of cancers with significant spatial patterning of risk. Further work is needed to relate the cancer data to other information on potential life-style and environmental factors.     

The influence of packaging materials on RF performance

At frequencies beyond 1 GHz, every component of the IC package contributes to the RF performance, whether required or not. In this work, we study the effects of packaging materials namely, the substrate and the globtop/underfill material on RF performance. We have measured interconnects on two area-array CSPs, the ball grid array and the polymer stud grid array using IMEC’s MCM-D technology. The measurements on the package interconnect show that the losses in the package substrate material account for about 50% of the total losses at 1.8 GHz and this drops to less than 20% at 5.2 GHz. The losses due to impedance mismatch dominate the losses especially below 10 GHz and considerable improvement in performance cannot be obtained by using an improved/expensive substrate. The other study is about the influence of globtop/underfill materials on wirebonds (through 3D EM simulations) as well as on standard 50 Ω MCM-D transmission lines (through experiments). While a higher value of dielectric constant of the globtop/underfill material is better on wirebonds, the influence of loss tangent is felt only above values of 0.1. The influence of seven different globtop/undefill materials on 50 Ω transmission lines has been used to extract their dielectric constant and loss tangent values at 30 GHz. These results are very valuable since one can hardly find the properties of globtop/underfill materials beyond 1 GHz.     

Promise is Debt, Threat Another Matter: The Effect of Credibility on the Interpretation of Conditional Promises and Threats.

Evidence from reasoning tasks shows that promises and threats both tend to receive biconditional interpretations. They also both display high speaker control. On the face of it, the only difference seems to be the positive or negative signing of the consequent. In a promise, the speaker tries to persuade the hearer to do something by holding out the prospect of a particular reward; in a threat, the speaker tries to refrain the hearer from doing something by holding out the prospect of a particular punishment. This paper investigates the respects in which conditional promises and threats differ further by means of an inference task. The credibility of the consequent was manipulated in order to examine whether the acceptability ratings of inferences based on promises and on threats would be equally affected. The results of the inference task and an analysis of the reasons people give for their answers suggest that the credibility of promises is less affected by the use of excessive consequents than the credibility of threats. In other words, promise remains debt, whereas threat is another matter. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

High quality LTCC resonator for voltage-controlled oscillator

Design and technology of microwave conductor lines embedded in low-temperature cofired ceramic (LTCC) multilayer substrates are summarized with a focus on achieving the highest possible quality (Q) factor for a given line inductance. The work was initiated to test the integrability of base station voltage-controlled oscillators (VCOs) in ceramic multilayer substrates. This approach leads to a miniaturization of current versions by a factor of 2 to 4. However, base station specifications for phase noise and hence resonator Q are extremely demanding. Therefore, both the design and the processing technology were optimized. By choosing a twin-line design with two parallel lines vertically separated by a single LTCC layer, Q factors of 90 and 180 have been achieved for integrated 5.5 nH inductors at frequencies of 640 MHz and 1650 MHz, respectively. Application of this result to VCO modules in standard LTCC technology already yields low phase noise levels, e.g., -136 dBc/Hz at 100 kHz offset, which is suitable for base station applications. However, further noise reduction is expected from a dedicated high Q fabrication process that uses conventional via punching and filling steps to replace the ceramic material between the two lines by conductive silver paste. This raises the Q to 120 and 200, respectively, at the two frequencies and adds extra degrees of freedom to LTCC design for low-loss wireless solutions.     

Aqueous Processing and Stabilization of Manganese Zinc Ferrite Powders via a Passivation–Dispersion Approach

A dispersion scheme for aqueous processing of manganese zinc ferrite suspensions is presented. The addition of oxalic acid leads to the formation of a uniform negative charge on the surface such that a cationic polyelectrolyte, polyethyleneimine (PEI), adsorbs and provides electrosteric dispersion. At 0.5 w/w (weight percent with respect to the dry powder) oxalic acid addition, there is a relatively uniform negative surface charge (approximately −30 mV) within the suspension pH range investigated (3–10), eliminating the isoelectric point (pH ∼7.6) present for the as-received metal oxide powder. At the addition of 0.5 w/w PEI on an oxalate-treated surface, the surface charge is constant and positive (∼20 mV) through a wide pH range, ∼5–10. The resulting rheological data for passivation–dispersion of relatively high-solids manganese zinc ferrite suspensions (∼80 wt%) demonstrate improved colloid stability with improved rheological properties. The resulting apparent viscosity and Bingham yield point is 0.01 Pa·s (12.0 cP) and 0.24 Pa (2.4 dynes/cm²), respectively. A sulfonated napthalene-based dispersant, typically used in industry, gives an apparent viscosity and Bingham yield point of 0.03 Pa·s (32 cP) and 3.1 Pa (31 dynes/cm²), respectively.     

Effect of storage temperature on phenolics stability in hawthorn (Crataegus pinnatifida var. major) fruits and a hawthorn drink

The stability of five major phenolics, namely (−)-epicatechin (EC), procyanidin B₂ (PC-B₂), chlorogenic acid (ChA), hyperoside (HP) and isoquercitrin (IQ), in hawthorn fruits and a canned hawthorn drink were evaluated during 6 months of storage in the dark at three different temperatures (4, 23 and 40 °C). HPLC with a diode-array detector was used to determine the contents of the individual compounds. The results showed that the studied phenolics in the hawthorn fruits and the drink were both stable at 4 °C and relatively unstable at 23 and 40 °C with varied extents of degradation. At room temperature (23 °C), marked degradations of EC and PC-B₂ were observed in both the fruits and the drink with around 50% and 30% decrease after a 6-month storage, respectively. A more significant decrease of the phenolics was observed at 40 °C, especially for EC and PC-B₂, which were almost completely degraded after a 6-month storage. HP, IQ and ChA were relatively stable at 23 °C, but unstable at 40 °C. Therefore, low-temperature storage is recommended for maintaining the quality and efficacy of hawthorn fruits and its preparations.     

Pressure wave propagation in a short tunnel caused by passing trains

The aerodynamic behaviour of pressure transients in railway tunnels due to the passage of train are accompanied by the wave reflection between the entrance and exit of the tunnel as well as the tunnel wall and train surface. This study presents a numerical method using the Harten-Yee upwind TVD scheme to simulate compression wave transients and reflection in a railway tunnel. The strength of the compression wave generated by the entrance of a train into a tunnel emerged within the applied calculation procedure, without any special consideration of the boundary condition for the entrance or exit of the tunnel as well as the train nose and tail. Good agreements were obtained when the initial pressure rise at tunnel entrance and the process of pressure variations in a short tunnel, which were calculated by the presented numerical method, were compared with experimental data. The pressure wave reflection at the entrance and exit, the unsteady flow around the train and the transmitted wave at tunnel exit portal were simulated. The transmitted wave at the tunnel exit portal is also discussed. In addition a method to determine the non-reflective boundary condition for multi-dimensional Euler equation is given.     

Peridynamic modeling of concrete structures

The peridynamic model described in Silling (Silling, S.A., 1998. Reformation of Elasticity Theory for Discontinuous and Long-Range Forces, SAND98-2176. Sandia National Laboratories, Albuquerque, NM), being a central-force model, is limited to modeling materials with a Poisson's ratio of 1/4. In this paper, the peridynamic model is generalized by adding pairwise peridynamic moments to simulate linear elastic materials with varying Poisson's ratios. The new model is called the “micropolar peridynamic model”. The micropolar peridynamic model is placed within a finite element context to enable efficacious application of boundary conditions and efficient computational solutions using an implicit, rather than an explicit solution algorithm. The implicit solution algorithm is suitable for quasistatic simulation of damage and cracking in concrete structures. With this new model, very simple tensile damage mechanisms at the micro structural (peridynamic) level are sufficient to explain a great deal of the microcracking (damage) and fracture mechanics observed in concrete structures. The new implementation appears to be computationally efficient.