基于μCLinux的NAT设备的设计与开发

NAT(网络地址翻译)技术有效地解决了IP地址紧缺的问题,为实现IPv4到IPv6的平滑过渡发挥了巨大的作用.在一个体积小、重量轻、价格低廉的嵌入式平台上实现NAT设备具有很好的实际意义.文中介绍了NAT技术的原理和实现过程,在自行设计的ARM7嵌入式硬件平台上基于μCLinux操作系统实现了NAT的功能,并通过实现其他相关功能,构建了完整的NAT设备,完成了小型网络接入Internet的方案.     

Tile-boundary artifact reduction using odd tile size and the low-pass first convention.

It is well known that tile-boundary artifacts occur in wavelet-based lossy image coding. However, until now, their cause has not been understood well. In this paper, we show that boundary artifacts are an inescapable consequence of the usual methods used to choose tile size and the type of symmetric extension employed in a wavelet-based image decomposition system. This paper presents a novel method for reducing these tile-boundary artifacts. The method employs odd tile sizes (2N + 1 samples) rather than the conventional even tile sizes (2N samples). It is shown that, for the same bit rate, an image compressed using an odd tile length low-pass first (OTLPF) convention has significantly less boundary artifacts than an image compressed using even tile sizes. The OTLPF convention can also be incorporated into the JPEG 2000 image compression algorithm using extensions defined in Part 2 of this standard.     

聚丙烯酸钠类高吸水性树脂的研究

采用反相悬浮聚合法合成高吸水性树脂.将丙烯酸(单体,水相)用氢氧化钠部分中和,然后与环己烷(溶剂,油相)共混,用水溶性的过硫酸钾做引发剂,N,N-亚甲基双丙烯酰胺做交联剂,在一定的反应温度和时间下,得到聚丙烯酸钠高吸水性树脂.     

氩等离子体辐照反相乳液接枝改性涤纶织物的研究

首次提出了在等离子体辐照后再用反相乳液接枝改性涤纶织物的新方法,探讨了接枝颗粒特征以及织物各项物理力学性能.接枝织物的结构及性能的测试结果表明:接枝物的尺寸远小于纤维的直径,在提高织物吸湿性的同时,对织物透气性能和强力等无明显影响;实验也证实了乳液中未接枝单体可以再次聚合.     

Asymmetric Regulation System Fit for Chinese Telecom Market

After the new round of restructuring of Chinese telecom sector,it's pressing to formulate and implement asymmetric regulation policies so as to shape an effectively competitive market structure in a relatively short term.This paper reviewed the asymmetric regulation policies and practices carried out in foreign telecom market,and then according to the specific situations of Chinese telecom market,proposed the principles and corresponding policies for establishing an asymmetric regulation system fit for Chin...     

箍筋末端135度弯钩二次就位法讨论

随着人们对建筑安全的日益重视 ,对建筑抗震要求的提高 ,国内外有关规范都对箍筋末端的设置作了明确规定 ,要求做成 135度弯钩。而在工程实践中 ,由于施工上的技术困难 ,很多工程都只设置成 90度弯钩。笔者提出的箍筋末端 135度弯钩二次就位法在基本不增加 90度弯钩施工难度与费用的基础上实现了 135度弯钩的施工 ,其法是可行的     

基于显微视觉的宏/微双重驱动微动台的自动标定

提出了基于压电技术的微操作系统的自动标定方法,采用混合式步进电机直接驱动的宏动平台,实现系统大行程宏动定位,安装在宏动平台上的压电陶瓷驱动的微动平台和精密光栅,实现亚微米级的分辨率和定位精度,通过以上两部分实现定位机构的全闭环反馈控制,采用显微视觉反馈获取微动台操作器在图像中的位置信息进行标定。实验结果表明:系统的动态和稳定性能良好,自动标定运算速度快,运行速度达到11 frame/s,实现了对系统的精确标定,标定精度达到0.1μm。     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.