Optimized partitioning of a wavelength distributed data interfacering network

A fiber optic ring network, such as fiber distributed data interface (FDDI), can be operated over multiple wavelengths on its existing fiber plant consisting of point-to-point fiber links. Using wavelength division multiplexing (WDM) technology, FDDI nodes can be partitioned to operate over multiple subnetworks, with each subnetwork operating independently on a different wavelength, and inter-subnetwork traffic forwarding performed by a bridge. For this multiwavelength version of FDDI, which we refer to as wavelength distributed data interface (WDDI), we examine the necessary upgrades to the architecture of a FDDI node, including its possibility to serve as a bridge. The main motivation behind this study is that, as network traffic scales beyond (the single-wavelength) FDDI's information-carrying capacity, its multiwavelength version, WDDI, can gracefully accommodate such traffic growth. A number of design choices exist in constructing a good WDDI network. Specifically, we investigate algorithms using which, based on prevailing traffic conditions, partitioning of nodes into subnetworks can be performed in an optimized fashion. Our algorithms partition the nodes into subrings, such that the total traffic flow in the network and/or the network-wide average packet delay is minimized     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

New ceramer high optical abrasion resistant transparent coating materials based on functionalized melamine and a tris(m-aminophenyl)phosphine oxide compound

Summary The synthesis of new high optical abrasion resistance coating materials has been undertaken by functionalizing melamine and tris(m-aminophenyl)phosphine oxide with a triethoxysilane containing reagent. These highly functionalized compounds have been used for coating a bis-phenol-A polycarbonate substrate by the sol-gel method. Preliminary data shows the abrasion resistance of the polymer substrate is considerably improved when it is coated by these optically clear materials.     

Experience in High-Temperature Thermomechanical Treatment with Helical Reduction in the Production of Axisymmetric Parts

Metal Science and Heat Treatment -     

An improved Gaussian approximation for probability of bit-erroranalysis of asynchronous bandlimited DS-CDMA systems with BPSK spreading

This paper analyzes probability of bit-error (P_e) performance of asynchronous bandlimited direct-sequence code-division multiple-access systems with binary phase-shift keying spreading. The two present methods of P_e analysis under bandwidth-efficient pulse shaping: the often-cited standard Gaussian approximation and the characteristic function (CF) method suffer from either a low accuracy in regions of low P_e (< 10^-3) or a prohibitively large computational complexity. The paper presents an alternate method of P_e analysis with moderate computational complexity and high accuracy based on a key observation. A sequence of chip decision statistics (whose sum yields a bit statistic) forms a stationary, m-dependent sequence when conditioned on the chip delay and phase offset of each interfering signal. This observation permits the generalization of the improved Gaussian approximation previously derived for the rectangular pulse and the derivation of a numerically efficient approximation based on the CF method. Numerical examples of systems using the square-root raised-cosine and IS-95 pulses illustrate THE P _e performance, user capacity and the accuracy of the proposed method     

Use of166mHo for calibration of gamma-ray spectrometers with semiconductor detectors

Translated from Atomnaya Énergiya, Vol. 67, No. 3, pp. 215–216, September, 1989.     

The effects of pressure on the isothermal fluid behavior of bituminous coals

An investigation into the effects of pressure (helium gas) on the isothermal fluid behavior includes: (1) the effect of pressure on the rate of melting and coking as evidenced by the rate constants k(melt) and k(coke); (2) the effect of pressure on the energies of activation of melting and coking; (3) the effects of pressure on the characteristic times; (4) the effects of pressure on the maximum isothermal fluidity. Results from the effects of pressure on k(melt) revealed that it was generally the high total sulfur, low nitrogen, low reactives/mineral matter ratio, medium rank coals which show the greatest increase in k(melt), whereas the highest rank coals show the least decrease in k(coke). The energies of activation of melting and coking were not significantly affected by pressure. The investigation also reveals increases or decreases in the respective times of softening, maximum fluidity, resolidification and total time of fluid behavior under isothermal pressurized conditions. There appears the possibility that these shifts may be rank dependent. Additionally, the lower rank coals show the largest relative increase in their fluidities when subjected to pressure. Empirical relationships were derived in order to quantitatively predict the maximum isothermal fluidity for most (fluid) coals at a given pressure.