A 300-MHz 25-/spl mu/A/Mb-leakage on-chip SRAM module featuring process-variation immunity and low-leakage-active mode for mobile-phone application processor

An on-chip 1-Mb SRAM suitable for embedding in the application processor used in mobile cellular phones was developed. This SRAM supports three operating modes - high-speed active mode, low-leakage low-speed active mode, and standby mode - and uses a subdivisional power-line control (SPC) scheme. The combination of three operating modes and the SPC scheme realizes low-power operation under actual usage conditions. It operates at 300 MHz, with leakage of 25 /spl mu/A/Mb in standby mode, and 50 /spl mu/A/Mb at the low-leakage active mode. This SRAM also uses a self-bias write scheme that decreases of minimum operating voltage by about 100 mV.     

End-to-End QoS for Video Delivery Over Wireless Internet

Providing end-to-end quality of service (QoS) support is essential for video delivery over the next-generation wireless Internet. We address several key elements in the end-to-end QoS support, including scalable video representation, network-aware end system, and network QoS provisioning. There are generally two approaches in QoS support: the network-centric and the end-system centric solutions. The fundamental problem in a network-centric solution is how to map QoS criterion at different layers respectively, and optimize total quality across these layers. We first present the general framework of a cross-layer network-centric solution, and then describe the recent advances in network modeling, QoS mapping, and QoS adaptation. The key targets in end-system centric approach are network adaptation and media adaptation. We present a general framework of the end-system centric solution and investigate the recent developments. Specifically, for network adaptation, we review the available bandwidth estimation and efficient video transport protocol; for media adaptation , we describe the advances in error control, power control, and corresponding bit allocation. Finally, we highlight several advanced research directions.     

Quantitative determination of aflatoxin B1 in chick liver

A method for the rapid and quantitative determination of aflatoxin B1 from small quantities of liver, around 1-2 g, is described. The extraction procedure involves acidification to pH 2 of the aqueous liver homogenates, extraction with chloroform: acetone and HPLC-fluorimetric detection after derivatization with trifluoroacetic acid. Quantitative recovery of aflatoxin B1 from chick liver was achieved and detection at levels of 0.2-1 ppb was proved feasible. The aflatoxin B1 concentration in chick liver after oral administration is also shown.     

Minimum-energy multicast in mobile ad hoc networks using network coding

The minimum energy required to transmit one bit of information through a network characterizes the most economical way to communicate in a network. In this paper, we show that, under a layered model of wireless networks, the minimum energy-per-bit for multicasting in a mobile ad hoc network can be found by a linear program; the minimum energy-per-bit can be attained by performing network coding. Compared with conventional routing solutions, network coding not only allows a potentially lower energy-per-bit to be achieved, but also enables the optimal solution to be found in polynomial time, in sharp contrast with the NP-hardness of constructing the minimum-energy multicast tree as the optimal routing solution. We further show that the minimum energy multicast formulation is equivalent to a cost minimization with linear edge-based pricing, where the edge prices are the energy-per-bits of the corresponding physical broadcast links. This paper also investigates minimum energy multicasting with routing. Due to the linearity of the pricing scheme, the minimum energy-per-bit for routing is achievable by using a single distribution tree. A characterization of the admissible rate region for routing with a single tree is presented. The minimum energy-per-bit for multicasting with routing is found by an integer linear program. We show that the relaxation of this integer linear program, studied earlier in the Steiner tree literature, can now be interpreted as the optimization for minimum energy multicasting with network coding. In short, this paper presents a unifying study of minimum energy multicasting with network coding and routing.     

Interfacial strength and chemistry of additive-free silicon nitride ceramics brazed with aluminium

Two kinds of additive-free silicon nitride ceramics were brazed with aluminium; one was with as-ground faying surfaces and the other was with faying surfaces heat-treated at 1073K for 1.8 ksec in air. The heat-treatment of the silicon nitride ceramics formed a silicon oxynitride layer on the faying surfaces and increased the brazing strength of the joints. A silica-alumina non-crystalline layer and a β′-sialon layer were formed successively from the aluminium side at the interface of the joints. The heat-treatment which made the former layer thicker is a necessary process in making reliable, strong brazed joints.     

Influence of initial growth layer and Ti underlayer on magneticproperties and recording characteristics of very thin films ofevaporated Co-Cr media

A Co-Cr film deposited directly on a substrate has an initial growth layer with low coercivity. However, the existence of a Ti underlayer prevents the formation of such a layer. As a result, Co-Cr film deposited on a Ti underlayer has high perpendicular anisotropy and coercivity even in cases of extremely thin film thickness (200 Å). As for the read-write characteristics of Co-Cr thin-film media, the existence of such an initial growth layer greatly improves the reproduced output level. The cause for this is considered to be that the free charges which appear on the back surface of the perpendicular recording layer are reduced and the demagnetization field acting on the recorded magnetization subsequently decreases due to the existence of the initial growth layer     

Nonlinear static and dynamic analysis of circular plates and shallow spherical shells using the collocation method

The present work investigates the efficacy and applicability of interior global orthogonal point collocation method to the axisymmetric nonlinear analysis of elastic circular plates and shallow spherical shells subjected to uniformly distributed transverse load. Spacewise discretisation has been carried out using a polynomial expansion with the zeros of a Chebyshev polynomial as collocation points. Timewise integration has been carried out with Newmark k-β scheme corresponding to average acceleration method. The static response and snap-through buckling results, as well as, the dynamic response and dynamic buckling results under a uniformly distributed step load have been obtained and found to agree closely with the available results.     

An alternating technique for evaluating weight functions for 3-D surface flaws in finite solid bodies

An efficient method, based on the Schwarz–Neumann alternating technique, is presented for computing weight functions of a general solid (3-D as well as 2-D), with embedded or surface-flaw configurations. The total rate of change of the crack-opening displacements, due to simple perturbations of crack-dimension characteristics, is conveniently decomposed into the infinite-domain and boundary-correction parts. The former is determined from available analytical solutions of ideal-shaped cracks, whereas the latter is computed numerically by imposing nil boundary-traction requirements for the displacement field corresponding to the weight functions. Numerical examples, with solutions for 3-D weighted-average and local stress intensity factors, indicate that the proposed method is very accurate and efficient.     

Repulsive Flux Pinning Force in NbTi/Nb Superconductor/Superconductor Multilayers

Flux pinning characteristics have been investigated for the Nb _x Ti_100-x /Nb(x = 65, 50 and 28) and Nb ₂₈ Ti ₇₂/Nb ₆₅ Ti ₃₅ superconductor(S)/superconductor(S^′) multilayers. The maximum of the pinning force F _{p⊥ max} perpendicular to the layer plane as a function of the structure modulation length λ has a peak in the quasi-two-dimensional region (λ～20 nm). The maximum. values of the F _{p⊥ max} versus λ curve are proportional to the difference of the GL coherence length (ξ _GL ) between the superconductive sublayers S and S^′. The results suggest that the large F _{p⊥ max} in the S/S^′ multilayer is caused by the repulsive pinning force due to Nb layers with larger ξ _GL .