一种的四进制CPM调制器的设计与FPGA实现

设计并实现了一种基于FPGA的四进制连续相位调制器（PCM）。该调制器的基带调制模块通过查表法实现，复杂度较低。仿真结果验证了设计的正确性。     

五种恒虚警方法性能分析

比较了五种恒虚警方法在各种杂波背景下的检测性能,得出CMLD-CFAR是工程上可以实现且检测性能比较好的一种恒虚警处理方法.     

Study of Disk-Loaded Waveguide Filled with Plasma

Recently disk-loaded waveguide has been widely used in high-power traveling wave tubes (HPTWT). It has been shown in many experiments that the interaction efficiency and output power can be increased greatly by injecting plasma into the vacuum microwave device. Using field analysis, the dispersion characteristics and the interaction impedance of the disk-loaded waveguide filled with plasma are analyzed in a strong longitudinal magnetic field. In conclusion, the frequency of the TM₀₁ mode increases as the density of the plasma increases. It also can be found when the plasma density increases to a large scale, the TM₀₁ mode of the disk-loaded waveguide overlaps the TG mode, these two modes couple each other and form the new hybrid modes.     

径向水平井弯曲转向机构影响因素仿真研究

针对径向水平井钻进中钻杆弯曲转向前进运动困难的问题,通过建立弯曲转向机构仿真有限元模型,对其主要影响因素:滑道轨迹曲率、间隙、工作压力、滚轮形状与位置和钻杆壁厚等用ANSYS软件进行仿真研究。研究表明:影响截面变形的主要因素是滑道曲率的改变和滑道摩擦因数,钻井失败时钻杆所受阻力的增大不是因为升高工作压力导致截面变形过大与滑道干涉所致,钻杆经校直段,钻头中轴线与校直中心线存在一定的角度,即钻杆的前进轨迹就会偏离理论值,或与地层干涉,或可能再次发生弯曲变形;另一主要原因是转向器滑道工作恶化。增加钻杆壁厚,降低工作压力和滑道摩擦因数,设计合理弯曲转向机构是解决问题的关键。     

用DSP实现多目标实时跟踪

介绍了在 TMS3 2 0 C62 0 3上实现 4个目标的快速跟踪技术。为了提高实时性和精确度 ,采用线性汇编优化实现。1个 3 2 0× 160主窗口的 DSP平均处理时间为 2 m s,3个 60× 60副窗口的 DSP平均处理时间各为 0 .4ms,实现了复杂背景下低对比度目标的快速跟踪。实验结果证明跟踪效果良好 ,解决了以前窗口开不大、跟踪速度慢的问题     

陶瓷企业实施MRPⅡ现状及问题分析

分析了我国陶瓷企业实施制造资源计划的现状，并提出了成功实施的方略，最后通过实例进行了分析。     

线性调频雷达最小作用距离范围内目标距离的测量

介绍了一种新的探测雷达最小作用距离的方法,打破了传统的最小跟踪距离受发射脉宽局限的限制,重点介绍对发射线性调频信号的雷达的近距离探测方法,并给出了仿真计算结果。     

电磁超声流量计的研制

基于电磁声换能器的原理，研制了一种新型的电磁超声流量计，并讨论提高测量精度的措施。     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

An Analysis of Citation Counts of ETRI‐Invented US Patents

From its foundation until 2004, ETRI has registered over 1,000 US patents. This letter analyzes the characteristics of these patents and addresses the explanatory factors affecting their citation counts. For explanatory variables, research team related variables, invention specific variables, and geographical domain related variables are suggested. Zero‐altered count data models are used to test the impact of independent variables. A key finding is that technological cumulativeness, the scale of invention, outputs in the electronic field, and the degree of dependence on the US technology domain positively affect the citation counts of ETRI‐invented US patents. The magnitude of international presence appears to negatively affect the citation counts of ETRI‐invented US patents.