Study of the effect of BDMA catalyst in the epoxy novolac curing process by isothermal DSC

Epoxy novolac/anhydride cure kinetics has been studied by differential scanning calorimetry under isothermal conditions. The system used in this study was an epoxy novolac resin (DEN431), with nadic methyl anhydride as hardener and benzyldimethylamine as accelerator. Kinetic parameters including the reaction order, activation energy and kinetic rate constants, were investigated. The cure reaction was described with the catalyst concentration, and a normalized kinetic model developed for it. It is shown that the cure reaction is dependent on the cure temperature and catalyst concentration, and that it proceeds through an autocatalytic kinetic mechanism. The curing kinetic constants and the cure activation energies were obtained using the Arrhenius kinetic model. A suggested kinetic model with a diffusion term was successfully used to describe and predict the cure kinetics of epoxy novolac resin compositions as a function of the catalyst content and temperature. Copyright © 2003 Society of Chemical Industry     

Oligo(ethylene oxide) side‐chain steric screening effects on conductimetric properties of grafted poly(4‐vinylpyridinium) salts in aqueous solutions

A set of poly[N‐oligo(ethylene oxide)yl 4‐vinylpyridinium tosylate] (P4VOEOOTs) has been prepared by spontaneous polymerization of 4‐vinylpyridine. This method gives a grafted polyelectrolyte having a positive charge on every backbone pyridinic moiety. The P4VP15Ts, P4VP164Ts, P4VP350Ts and P4VP750Ts aqueous solution conductivities were determined in the concentration range from 6 × 10^?4 to 10^?2 M at 25 °C. The variation of the conductivity versus concentration of the investigated system exhibits typical polyelectrolyte behaviour. The polyelectrolyte mobility was found to be dependent on the oligo(ethylene oxide) (OEO) side‐chain length. Manning's rod‐like model fails to describe these results. A simple steric effect is proposed to explain the influence of the OEO length. Copyright © 2003 Society of Chemical Industry     

Flow Reaction Forces upon Blowdown of Safety Valves

The activation of safety valves causes the development of flow reaction forces that have to be transferred in an adequate way via the piping to the steel structure or via the connected vessel into the foundation. If the safety valve outlet piping is connected to a blowdown system or, in case of blowing off into the atmosphere, are equipped with a T‐piece at the outlet, the stationary reaction forces are compensated completely. The transient opening process, however, develops flow reaction forces which culminate in peaks of short duration. In this article, a simple method will be proposed for the estimation of the resulting reaction forces as a function of the length of the pipe at the safety valve outlet. CFD calculations and blowdown tests executed with a full‐lift safety valve have confirmed this method on principle. Special importance is attributed to the short duration of the effect of the reaction forces which seems to have only a negligible impact on the supporting steel structure.     

Unresolved controversies concerning psychopathy: Implications for clinical and forensic decision making.

At some point in their careers, clinicians who work or consult in forensic and correctional settings will almost certainly encounter individuals who exhibit psychopathic personality features. Because of the widespread use of this disorder to inform legal and clinical decision making, psychologists should be exceedingly familiar with the relevant research literature on this topic before venturing into these settings. This article reviews the empirical bases of several clinically relevant claims and assertions regarding psychopathy and concludes that many areas of research are decidedly more equivocal in their findings than is commonly perceived. Although there is much to be gained by assessing psychopathy in various contexts, clinicians need to be cautious about drawing overzealous and empirically questionable conclusions about an important disorder that also has great potential for abuse. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

Untersuchung der Verteilung und Intensität filamentierter Barrierenplasmen für die Behandlung von Oberflächen

The application of barrier discharges at atmospheric pressure in air expands on the market of plasma technology, because it is an ecological and cost‐effective alternative to other processes of surface treatment. These plasmas usually consist of a multitude of spatially and temporally localized filaments, whose distribution should be as even as possible for homogeneous treatment. This holds especially for the plasma treatment of sensitive goods such as wool or other textiles. In equipment for continuous pass of material the barrier arrangements often consist of a system cylinder – cylinder or cylinder – plane, whereby the gap width changes locally. Space distribution and intensity of filaments has been investigated by means of short‐time photography and spatially resolved measurement of current distribution and energy distribution derived from it. The local dependency found can be explained by means of a capacitive equivalent circuit.     

Micro-prober for wafer-level low-noise measurements in MOS devices

Low-frequency noise measurements represent an interesting investigation technique for the characterization of the quality and reliability of microelectronic materials and devices. Performing meaningful noise measurements at low and very low (f<1 Hz) frequencies, however, may be quite challenging, particularly because of the many sources of interference that superimpose on the noise signal. For this reason, packaged samples are preferred because they allow accurate shielding from the external environment, and because keeping the sample in close proximity to the low-noise biasing system and amplifier reduces microphonic and electromagnetic disturbances. Notwithstanding this, the possibility of performing low-frequency noise measurements at wafer level would be quite interesting, both because of the ease of obtaining wafer-level samples from industries with respect to packaged samples, and because this would avoid possible packaging-process induced device degradation. The purpose of this work is to demonstrate that it is, in fact, possible to design and build a dedicated probe system for performing high-sensitivity, low-frequency noise measurements on metal-oxide-semiconductor devices at wafer level.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

A redundant multivalued logic for a 10-Gb/s CMOS demultiplexer IC

A redundant multivalued logic is proposed for high-speed communication ICs. In this logic, serial binary data are received and converted into parallel redundant multivalued data. Then they are restored into parallel binary data. Because of the multivalued data conversion, this logic makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was fabricated using a 0.18-/spl mu/m CMOS process. The IC achieved an operating speed of 10 Gb/s with a supply voltage of only 1.3 V and with power consumption of 38 mW. This logic may achieve CMOS communication ICs with an operating speed several times greater than 10 Gb/s.