Active,passive and transpassive dissolution of a nickel base super alloy in concentrated acid mixture solution

The electrochemical and corrosion behaviour of a nickel base super alloy (C-263) has been investigated in the deaerated binary and ternary solution mixture of concentrated phosphoric acid, acetic acid, sulphuric acid, nitric acid or water using potentiostatic technique at 35°C. The possibilities of electropolishing of this alloy in these solution mixtures have been also explored. The alloy showed distinct active, passive and transpassive behaviour in the experimental solutions. The alloy remained active and turned passive in the negative potential region. Transpassive dissolution of the alloy is observed and electropolishing is achieved in this region. The best electropolishing is obtained in 50% H₃PO₄ + 40% CH₃COOH + 10% H₂SO₄. Higher content of water in the electrolytic solution is not useful for electropolishing of the alloy The experimental results also suggest that a current plateau in the transpassive potential region is not a sufficient condition to achieve electropolishing.     

Synthesis and analysis of transformer-isolated converters

A systematic and straightforward procedure is developed for the synthesis and analysis of transformer-isolated power converters. The procedure can be used to determine the ranges of duty-ratio over which the transformer-isolated power converters of a given class can be operated without transformer saturation. The procedure can also be used to study the dependence of the power converter switch stresses on duty-ratios. This information is useful in the selection of the transformer-isolated power converter most suitable for a given application and in the design of this power converter with minimum switch stresses, high power density, and low cost     

Characterization of allergoids from ovalbumin in vitro and in vivo

Several in vivo and in vitro methods for monitoring immunological properties of two allergoids obtained by formaldehyde treatment of ovalbumin (OA) were developed. The calculated molecular weight of allergoids was 80 kD (OA-F1) and 165 kD (OA-F2), respectively. The allergenic activity in vitro of allergoids in mast-cell histamine release assay was 1000 times lower than of OA. Both allergoids showed reduced ability to induce passive cutaneous anaphylaxis in the Sprague-Dawley rats or systemic anaphylaxis in Dunkin-Harley guinea-pigs. The ability of OA and allergoids to bind to the OA-specific IgE antibodies was measured in vivo by the inhibition of passive cutaneous anaphylaxis (PCA-inhibition). Allergoid binding to IgE was 51-66% lower than the native allergen. Moreover, the avidity of OA-specific IgG antibodies, measured by ELISA-inhibition, for allergoids and allergen was of the same order. Allergoids induced a different pattern of humoral immune response from that, induced by the native allergen. Thus, after immunization of BALB/c mouse, both allergoids induced a higher production of IgG and a lower production of IgE than OA, only OA-F2 induced a lower production of IgG1. The differences in the IgA response to the immunogens was not significant. Delayed hypersensitivity studies in the BALB/c mouse showed that allergoids were 5- to 12-times less effective in inducing a cell-mediated immune response than OA. The present study provides a battery of immunological methods for preclinical testing of modified allergens.     

Deformation and fracture of glass bead/ CTBN-rubber/epoxy composites

Carboxyl-terminated butadiene-acrylonitrile-rubber decreases modulus and yield stress of the studied epoxy but increases fracture toughness. The addition of glass bead compensates for the loss in modulus but has little effect on yield stress. However, it significantly contributes to the fracture toughness by providing additional mechanisms for toughening of both the unmodified and rubber-modified epoxy. For the toughened epoxies studied, fracture surfaces gave only limited information on fracture mechanisms since significant energy absorption also occurs in the material below the fracture surface. Suggestions for suitable material compositions for fiber composite matrices are given.     

A novel way to treat refractory waste: Sonication followed by wet oxidation (SONIWO)

The effectiveness of the hybrid system sonication followed by wet oxidation (SONIWO) to treat otherwise refractory waste has been demonstrated. In such a hybrid system homogeneous CuSO₄ catalyst was found to be very efficient.     

Cold forging and chemical heat treatment of the casing of the internal joint for VAZ cars

The technological process of cold forging applied for the first time in the production of the casing of the internal joint with races is described. The process operations of cold forging and the annealing and carburizing regimes for this part me described.     

Increasing the interference immunity of broadband systems for measuring and transmitting information by utilizing nonlinear signal processing methods

A method is considered for increasing the immunity from interference of broadband systems for measuring and transmitting information. It is based on utilizing nonlinear methods to process spread-spectrum signals. The possibility is investigated of using a quasioptimal receiving device which can be implemented in practice. It is shown that the proposed method makes it possible to solve the rejection problem at the physical level. Translated from Izmeritel'naya Tekhnika, No. 11, pp. 13–15, November, 1996.