Tensile Properties and Failure Mechanism of a New 3D Nonorthogonal Woven Composite Material

Tensile properties and failure mechanism of a newly developed three-dimensional (3D) woven composite material named 3D nonorthogonal woven composite are investigated in this paper. The microstructure of the composite is studied and the tensile properties are obtained by quasi-static tensile tests. The failure mechanism of specimen is discussed based on observation of the fracture surfaces via electron microscope. It is found that the specimens always split along the oblique yarns and produce typical v-shaped fracture surfaces. The representative volume cell (RVC) is established based on the microstructure. A finite element analysis is conducted with periodical boundary conditions. The finite element simulation results agree well with the experimental data. By analyzing deformation and stress distribution under different loading conditions, it is demonstrated that finite element model based on RVC is valid in predicting tensile properties of 3D nonorthogonal woven composites. Stress distribution shows that the oblique yarns and warp yarns oriented along the x direction carry primary load under x tension and that warp yarns bear primary load under y tension.     

热处理非晶态Ni-P合金镀层的晶化过程

运用电沉积的方法在45钢基体上制备Ni-P合金镀层,使用差示扫描量热法(DSC)和热重法(TG)分析非晶态NiP合金镀层在20℃/min加热速率下的热效应和质量变化。在300℃和400℃分别对镀层进行0,15,30,45,60,75min的热处理,采用扫描电镜(SEM)、能谱仪(EDS)、X射线衍射仪(XRD)、显微硬度计对镀层进行表征。结果表明:Ni-P合金镀层在加热过程中的放热峰出现在284.8℃处,镀层的质量和元素组成稳定;晶化过程经历了非晶态、亚稳态NiP和Ni5P2、稳定态Ni3P的转变;经过热处理后,镀层的显微硬度显著提高,最大值达1036.56HV,约为镀态的2倍;热处理态镀层的耐NaCl溶液腐蚀性能比镀态有所下降,但两者都比45钢基体好。     

小河嘴水电站增效扩容改造电气设备分析

小河嘴水电站已运行四十多年,设备老化,故障多,自动化水平低,对该站进行增效扩容改造是必要的,而且也是可行的。     

Reliability analysis on systems with self-healing and self-repairing under different environments and shock models

Inspired by the process of self-healing of biological damage, high technology materials with self-healing and self-repairing mechanisms have been developed for high reliability and long lifetime. Therefore, the reliability modeling on intelligent systems with healing performance has become a research hotspot. Based on the diversity of healing mechanisms, this paper proposes a two-phase reliability model method on self-healing and self-repairing systems. Impacts of environments, shock loads, self-healing, and self-repairing mechanisms are taken into account in this novel model. Besides, system lifetime and some reliability indexes under two shock models are derived, respectively. Moreover, Monte Carlo simulations are conducted to verify the accuracy of reliability under two models. Finally, an engineering case of metallized film capacitor is provided to illustrate the effectiveness and applicability of the proposed models by comparing numerical results and simulation results.     

Comparison of approaches based on optimization and algebraic iteration for binary tomography

Binary tomography represents a special category of tomographic problems, in which only two values are possible for the sought image pixels. The binary nature of the problems can potentially lead to a significant reduction in the number of view angles required for a satisfactory reconstruction, thusly enabling many interesting applications. However, the limited view angles result in a severely underdetermined system of equations, which is challenging to solve. Various approaches have been proposed to address such a challenge, and two categories of approaches include those based on optimization and those based on algebraic iteration. However, the relative strengths, limitations, and applicable ranges of these approaches have not been clearly defined in the past. Therefore, it is the main objective of this work to conduct a systematic comparison of approaches from each category. This comparison suggested that the approaches based on algebraic iteration offered both superior reconstruction fidelity and computation efficiency at low (two or three) view angles, and these advantages diminished at high view angles. Meanwhile, this work also investigated the application of regularization techniques, the selection of optimal regularization parameter, and the use of a local search technique for binary problems. We expect the results and conclusions reported in this work to provide valuable guidance for the design and development of algorithms for binary tomography problems.     

Direct raycasting of unstructured cell-centered data by discontinuity Roe-average computation

In the field of computational fluid dynamics (CFD), the upwind finite volume method (FVM) is widely applied to solve 3D flows with discontinuity phenomena (e.g., shock waves). It produces unstructured data at the center of each cell (cell-centered data) with the flow discontinuity constraint on the inner-face between face-neighboring cells. For visualization, existing approaches with interpolation usually pre-extrapolate cell-centered data into cell-vertexed data (data values given at cell vertices) and only handle cell-vertexed data during actual rendering, which unconsciously depress the rendering accuracy and violate the discontinuity constraint. In this paper, we propose a novel method to visualize cell-centered data directly avoiding extrapolation and keep the discontinuity in the rendering data on the framework of multi-pass raycasting. During resampling, the field is reconstructed using the original cell-centered data value and the cell-gradient estimated by Green–Gauss theorem. To keep the discontinuity, we reconstruct the field at an inner-face resampled point using both the face-adjacencies and get two discontinuous field values. Then the field is obtained by computing Roe-average of the two. The analysis and experiments demonstrate that our approach gains a high-accuracy reconstruction and leads to a high-quality image.     

A comparative study of two techniques for improving power‐handling capability of CMOS T/R switches

This article proposes an asymmetric topology for transmit/receive (T/R) switches and more importantly presents a comparative study of both LC‐tuned and resistive body‐floating techniques for improving the power‐handling capability of the T/R switches in the same 0.18‐μm triple‐well CMOS. It is shown from simulations and measurements that the switches adopting either technique achieve comparable performances. For instance, the switch employing the LC‐tuned body‐floating technique exhibits insertion loss of 1.5 dB, isolation of 23.5 dB, and power‐handling capability of 22.5 dBm at 5.2 GHz, whereas the switch using the resistive body‐floating technique exhibits insertion loss of 1.3 dB, isolation of 24 dB, and power‐handling capability of 22.2 dBm, respectively. Therefore, one can conclude that the asymmetric topology with the resistive body‐floating technique is more suitable for designing T/R switches for wireless local area network applications as it consumes smaller silicon area. © 2010 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2010.     

Robustness of fuzzy operators in environments with random perturbations

In many applications, such as intelligent decision systems, there are usually random perturbations caused by the constant changing of real situations, thus the analysis of the robustness with respect to random perturbations is practically important. In the side of fuzzy methods, a corresponding problem arises: will a small random perturbation of fuzzy input cause a big variance of fuzzy output? This paper study the robustness of fuzzy schemes in environments with random perturbations. It focuses on fuzzy algebraic operators, and proposes two methods to analyze their robustness in environments with random perturbations. The effectiveness and features of the methods are shown by simulations.     

媒体舆论引导仿真

使用multi-Agent的建模思想,以现实为基础建立了一个舆论涌现的仿真模型.该模型主要由个体和媒体以及它们之间的规则组成.个体的属性包括了个体之间的信任度、个体观点的可信度和个体的从众性;媒体的属性包括媒体的影响范围和权威度.规则包括个体交互规则和个体与媒体的交互规则.通过仿真证明了模型是合理的,并且用该模型来仿真媒体对舆论演化的引导作用,从媒体的数量和报道频率2个方面研究媒体在舆论形成过程中的引导作用,结果发现积极媒体的数量越多对舆论的引导作用越强,媒体的报道频率增加会对舆论的形成产生积极效果,但是超过一定次数时对舆论的影响作用有限.最后通过对模拟结果的分析,提出了通过媒体来引导舆论的方式.