一种用于SOC设计中的智能I/O处理器的实现

文章介绍了SOC设计流程，智能I／O处理器组成，在开发该处理器对VHDL源代码的优化问题。     

环保型隧道防火涂料的研究

介绍了国内外公路隧道、铁路隧道及地铁火灾情况 ,研制出一种可在潮湿环境中使用、火灾发生时无有害气体产生的环保型隧道防火涂料。涂层厚度 18～2 0 mm,耐火极限达 3小时。为防止涂料加水拌和后沉淀分层 ,增加涂料的和易性 ,研制出一种分散剂。     

医用聚氯乙烯材料的表面光接枝改性

研究了在不排氧氛围下 ,紫外光照射 ,以二苯甲酮 (BP)为光引发剂 ,甲基丙烯酸缩水甘油酯(GMA)在医用聚氯乙烯 (PVC)薄膜表面的气相接枝聚合。探讨了反应条件对接枝结果的影响 ,并用正交法指出了影响因素的显著性。用傅立叶红外 (FT- IR)、水接触角作为接枝改性结果的表征。FT- IR谱图表明 GMA已接枝到 PVC膜表面。水接触角由接枝前的 78°下降到 5 4°     

济钢转炉煤气储存加压系统存在缺陷及处理措施

济钢燃气厂针对济钢转炉煤气储存加压系统的设备现状，组织了一次设备大修，大修后煤气柜升降速度提高到了1．0m/min，并解决了加压机前负压等问题。     

减压渣油与FCC油浆共炭化的化学组成变化

考察了齐鲁石化胜利炼油厂催化油浆（FCC）和胜利减压渣油（VR）在490℃，0.8MPa下不同混合比的原料和不同反应时间的中间产物的HS、TS、PS、P及其1h中间产物的HS和TS的^1H-NMR。数据结果反映了体系的反应速度。掺入FCC油浆抑制了VR的反应活性，降低了体系的反应速度，增加了基质的溶解度；1h中间产物的组成结构更接近于原料及反应体系的反应性和基质的溶解度；1h中间产物的芳香度越高，取代基越少，侧链越短，基质对VR中的活性反应组分在炭化早期生成的高度缩合物质的溶解度越大。     

A new efficient method for one‐pot conversions of aryl carboxylic acids into nitriles without solvent

A new efficient method for synthesising nitriles, important organic reagents, is reported in this paper. In an environmentally benign solvent‐free system, aryl carboxylic acids were converted into the corresponding nitriles via one‐pot reactions, by amidation with ethyl carbamate followed by dehydration with thionyl chloride, in excellent yields. The results showed that the method has the advantages of lower cost, higher yield, less pollution and greater ease of work‐up. Copyright © 2008 Society of Chemical Industry     

APT（STLRI）—1.78型单模光纤（缆）连接器简介

利用引进的制造技术和设备,制作出了 APT(STLRI)—1.78型系列化光纤连接器。     

Enhanced light output in nitride-based light-emitting diodes by roughening the mesa sidewall

In this letter, we will report on a nitride-based light emitting diode with a mesa sidewall roughening process that increases light output power. The fabricated GaN-based light-emitting diode (LED) wafers were first treated through a photoelectrochemical (PEC) process. The Ga/sub 2/O/sub 3/ layers then formed around the GaN : Si n-type mesa sidewalls and the bottoms mesa etching regions. Selective wet oxidation occurred at the mesa sidewall between the p- and the n-type GaN interface. The light output power of the PEC treated LED was seen to increase by about 82% which was caused by a reduced index reflectance of GaN-Ga/sub 2/O/sub 3/-air layers, by a rough Ga/sub 2/O/sub 3/ surface, by a microroughening of the GaN sidewall surface, and by a selective oxidation step profile of the mesa sidewall that increases the light-extraction efficiency from the mesa sidewall direction. Consequently, this wet PEC treated process is suitable for high powered nitride-based LEDs lighting applications.     

A new method for producing high melt strength polypropylene with reactive extrusion

A high‐melt‐strength polypropylene (HMSPP) was prepared using a twin‐screw reactive extruder from a commercial isotactic polypropylene through two stages, first, maleic anhydride is grafted to polypropylene to obtain a maleic anhydride‐grafted polypropylene (PP‐g‐MA), and then the grafted polymer is reacted with epoxy to extend the branched chain. Fourier transformed infrared spectroscopy indicated that maleic anhydride was grafted on polypropylene and reacted with epoxy. Melt flow rate and sag resistance test showed that the melt strength of the HMSPP improved considerably. Differential scanning calorimetry test showed that the long chain branches (LCBs) act as a nucleating agent in the crystallization of the HMSPP, which leads to a high crystallization temperature and crystallinity. Furthermore, the LCB efficiency of the HMSPP can also be calculated by analyzing its rheological property. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers