APT（STLRI）—1.78型单模光纤（缆）连接器简介

利用引进的制造技术和设备,制作出了 APT(STLRI)—1.78型系列化光纤连接器。     

磷矿的电选试验研究

清水沟中低品位磷矿性质复杂，嵌布粒度细，磨至-0．174mm 92．8％，通过振动—气流联合作用摩擦荷电，采用悬浮电选机经-粗-精-扫电选。可由含P2O5为24．47％的原矿获得含P2O5为30．23％。回收率为83．26％，杂质含量合格的磷精矿。     

Enhanced light output in nitride-based light-emitting diodes by roughening the mesa sidewall

In this letter, we will report on a nitride-based light emitting diode with a mesa sidewall roughening process that increases light output power. The fabricated GaN-based light-emitting diode (LED) wafers were first treated through a photoelectrochemical (PEC) process. The Ga/sub 2/O/sub 3/ layers then formed around the GaN : Si n-type mesa sidewalls and the bottoms mesa etching regions. Selective wet oxidation occurred at the mesa sidewall between the p- and the n-type GaN interface. The light output power of the PEC treated LED was seen to increase by about 82% which was caused by a reduced index reflectance of GaN-Ga/sub 2/O/sub 3/-air layers, by a rough Ga/sub 2/O/sub 3/ surface, by a microroughening of the GaN sidewall surface, and by a selective oxidation step profile of the mesa sidewall that increases the light-extraction efficiency from the mesa sidewall direction. Consequently, this wet PEC treated process is suitable for high powered nitride-based LEDs lighting applications.     

A new method for producing high melt strength polypropylene with reactive extrusion

A high‐melt‐strength polypropylene (HMSPP) was prepared using a twin‐screw reactive extruder from a commercial isotactic polypropylene through two stages, first, maleic anhydride is grafted to polypropylene to obtain a maleic anhydride‐grafted polypropylene (PP‐g‐MA), and then the grafted polymer is reacted with epoxy to extend the branched chain. Fourier transformed infrared spectroscopy indicated that maleic anhydride was grafted on polypropylene and reacted with epoxy. Melt flow rate and sag resistance test showed that the melt strength of the HMSPP improved considerably. Differential scanning calorimetry test showed that the long chain branches (LCBs) act as a nucleating agent in the crystallization of the HMSPP, which leads to a high crystallization temperature and crystallinity. Furthermore, the LCB efficiency of the HMSPP can also be calculated by analyzing its rheological property. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

铁素体球墨铸铁与20钢的闪光对焊

试验使用铁素体球墨铸铁和20钢的实心棒料进行了闪光对焊，通过改变次级电压4～8级，通电时间3～5s，观察其焊接接头组织的变化并测定其抗拉强度。结果表明，接头由三个区组成；当通电时间一定时，抗拉强度随次级电压的升高先减小后增大；当次级电压一定时，抗拉强度随通电时间的增加而增大。在次级电压为8级、通电时间为5s时，抗拉强度达最大值，为370．8MPa，是20钢母材的90.4％，是球墨铸铁母材的83.7％。     

Modeling for local dynamic behaviors of phenol biodegradation in bubble columns

A coupled three-dimensional (3-D) model, combining hydrodynamics with biochemical reactions, was developed to simulate the local transient flow patterns and the dynamic behaviors of cell growth and phenol biodegradation by yeast Candida tropicalis in the bubble-column bioreactor, using the computational fluid dynamic (CFD) method. In order to validate this proposed model effectively, the validation of the local hydrodynamic characteristics of the gas-mineral salt solution (gas-liquid) two-phase system, with the phenol concentration of 1200 mg/L, and with the absence of cells, was performed in a square-sectioned bubble column bioreactor using the LDA system and conductivity probe. Furthermore, the validation of phenol biodegradation behaviors by yeast Candida tropicalis at different initial concentrations of phenol and cell was also carried out in the above bubble-column bioreactor. The results indicated that the model simulations had a satisfying agreement with the experimental data. Finally, the local instantaneous flow and phenol biodegradation features including gas holdup, gas velocity, liquid velocity, cell concentration and phenol concentration inside the bioreactor were successfully predicted in different-scale bubble columns by the proposed model. © 2006 American Institute of Chemical Engineers AIChE J, 2006     

Hydrothermal Reaction Mechanism and Pathway for the Formation of K2Ti6O13 Nanowires

Calculations and detailed first principle and thermodynamic analyses have been performed to understand the formation mechanism of K₂Ti₆O₁₃ nanowires (NWs) by a hydrothermal reaction between bulk Na₂Ti₃O₇ crystals and a KOH solution. It is found that direct ion exchange between K⁺ and Na⁺ plus H⁺ interactions with [TiO₆] octahedra in Na₂Ti₃O₇ promote the formation of an intermediate H₂K₂Ti₆O₁₄ phase. The large lattice mismatch between this intermediate phase and the bulk Na₂Ti₃O₇ structure, and the large energy reduction associated with the formation of this intermediate phase, drive the splitting of the bulk crystal into H₂K₂Ti₆O₁₄ NWs. However, these NWs are not stable because of large [TiO₆] octahedra distortion and are subject to a dehydration process, which results in uniform K₂Ti₆O₁₃ NWs with narrowly distributed diameters of around 10 nm.     

Diameter NASREQ协议在卫星移动通信系统中的应用研究

如何对接入网络的用户进行身份认证、授予相应权限并进行计费,是卫星移动通信系统网络管理需解决的重要问题。简要介绍认证、授权、计费(AAA)的基本概念,分析Diameter协议框架、协议原理以及协议应用于网络接入的特点。阐述协议中包含的各种应用,给出Diameter NASREQ应用的一种系统模型。重点研究Diameter NASREQ协议在卫星移动通信系统中的应用,详述应用中客户机和服务器中各模块的功能和工作原理。通过分析,说明该应用的可行性及有效性。