Some electron microscope observations of longitudinal splitting from surface flaws in Kevlar 29

Journal of Materials Science Letters -     

Study of the nozzle flow in a cross-flow turbine

An investigation of the flow inside the nozzle of a Cross-Flow turbine, which is a hydraulic turbine where the rectangular water jet issuing from the nozzle crosses the rotor blades twice, is presented here. Part of the investigation consisted in the experimental measurement of the static pressure distribution on the inside walls of two different nozzle configurations, both with the nozzle mounted alone and in the presence of a rotor. The tests performed in the presence of a rotor included the measurement of efficiency and covered a wide range of working conditions around the best efficiency point. The analysis of the results obtained in this way give us an indication of the influence of the turbine non-dimensional volume flow rate on the flow inside the nozzle and the way it affects the reaction degree of the machine and its efficiency level. Although most of the tests were carried out with a 25-blade rotor, one of the analysed nozzle configurations (that with an inside vane) was also tested with a 10-blade rotor, permitting the assessment of the effect the number of blades has on the flow in the nozzle.The flow inside the nozzle with no inside vane was numerically analysed using a method based on a Schwarz-Christoffel conformal transformation of variables. The numerical results show a fair agreement with the experimental data collected when the rotor was not present. A qualitative discussion of some of the losses occurring in the nozzle is advanced based on the computer results, and its conclusions are used for explaining the poor performance of the nozzle with no inside vane.     

1.04 GBd low EMI digital video interface system using small swingserial link technique

In a high-resolution flat panel system, a conventional interface that directly connects a liquid crystal display (LCD) controller to a flat panel cannot overcome the problems of excess EMI (electromagnetic interference) and power caused by full-swing transmission signals in parallel lines. This paper presents a high-speed digital video interface system implemented with a low-cost standard CMOS (complimentary metal-oxide-semiconductor) technology that can mitigate EMI and power problems in high-resolution flat panel display systems. The combined architecture of the high-speed, small number of parallel lines and low-voltage swing serial interface can support resolutions from VGA (640×480 pixels) up to XGA (1024×768 pixels) with significant power improvement and drastic EMI reduction. To support high-speed, low-voltage swing signaling and overcome channel-to-channel skew problems, a robust data recovery system is required. The proposed digital phase-locked loop enables robust skew-insensitive data recovery of up to 1.04 GBd     

Pulmonary Wegener''s disease mimicking tuberculosis]

We report a case of early Wegener's disease mimicking tuberculosis in a 36 year old man. Lungs are solely affected for 6 months. Unusual appearance of radiographic features with large apical excavations explain the delai for the diagnosis. We discuss morphological features in the lungs and kidney.     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

Effect of the pressure drop rate on cell nucleation in continuous processing of microcellular polymers

Microllular plastics are cellular polymers characterized by cell densities greater than 10⁹ cells/cm³ and cells smaller than 10 μm. One of the critical steps in the continuous production of microcellular plastics is the promotion of high cell nucleation rates in a flowing polymer matrix. These high nucleation rates can be achieved by first forming a polymer/gas solution followed by rapidly decreasing the solubility of gas in the polymer. Since, in the processing range of interest, the gas solubility in the polymer decreases as the pressure decreases, a rapid pressure drop element, consisting of a nozzle, has been employed as a continuous microcellular nucleation device. In this paper, the effects of the pressure drop rate on the nucleation of cells and the cell density are discussed. The experimental results indicate that both the magnitude and the cell density are discussed. The experimental results indicate that both the magnitude and the rate of pressure drop play a strong role in microcellular processing. The pressure phenomenon affects the thermodynamic instability induced in the polymer/gas solution and the competition between cell nucleation and growth.     

Evaluation of in vitro stability of large unilamellar liposomes coated with a modified polysaccharide (O-palmitoylpullulan)

Aiming at encapsulation of a hydrosoluble drug, large unilamellar liposomes (LUV) of egg phosphatidylcholine (PC) were coated with a natural polysaccharide derivative, O-palmitoylpullulan (OPP), and its in vitro stability evaluated using fluorescent probes. This coating (in OPP/PC weight ratio of 3) improved significantly the in vitro stability of LUV by decreasing both the permeability and fluidity of the liposomal membrane.This paper was accepted for publication after the 1995 Conference of the European Society of Biomaterials, Oporto, Portugal, 10–13 September.     

Infrared and ultraviolet–visible spectroscopic studies of silica, [(Cp)2ZrCl2] and trimethylaluminum interactions

Infrared and UV–vis studies of metallocene immobilization on silica are reported here. The results have indicated changes in the Zr coordination sphere of metallocene depending on the immobilization route used. The reaction of [(Cp)₂ZrCl₂] with silica formed [(Cp)₂ZrCl]⁺[SiO]⁻ species. The same metallocene, reacting with TMA modified silica, formed monomethylated and dimethylated species by the substitution of chloro for methyl ligands, stabilized on the surface by interaction with “MAO-like” species (methylaluminoxane, MAO). These monomethylated and dimethylated cationic zirconium species are the active centers for the polymerization reaction. Different order of TMA addition in the silica modification step generated surface species of a similar nature, differing in their relative quantities. The highest amount of these active species was obtained when the support was added to the TMA solution rather than adding the TMA solution to the silica support. This was the most significant parameter affecting catalytic activity in ethylene polymerization.