川东气藏直井完井方法的产能预测研究

在分析研究目前国内外油气井完井产能计算经验公式的基础上，针对四川气田东部浅层气藏常用的几种完井方式，建立了该地区完井产能预测的数学模型。通过实例计算，表明了其数学模型的准确可行性，并为出砂井和非出砂井的完井方式提供了选择依据：对于出砂井，砾石裸眼充填完井方式是最理想的完井方式；对于非出砂井，实际裸眼完井的产能最大。得出的结论对该地区直井完井方式的选择，完井参数优化设计以及产能预测具有一定的指导作用。     

板式换热器常见故障及处理

介绍了板式换热器使用中经常出现的外漏、串液等故障,并对此进行了分析,提出了合理的解决方法。     

结合RDF实现对XML文档的RBAC

文章提出了一种面向XML文档的基于XMLschema并结合RDF的访问控制模型,它实现了对XML文档的细粒度的安全访问控制,同时提供了对XML文档中associationsecurityobject的安全访问控制。     

Laterally coupled buried heterostructure high-Q ring resonators

All-buried InP-InGaAsP ring resonators laterally coupled to bus waveguides are demonstrated. The buried configurations offer a lower built-in refractive index step along the resonator periphery, which affords enhanced optical coupling coefficients between the waveguides and reduced scattering losses caused by the resonator sidewall imperfections. Very low optical intensity attenuations of 0.4 cm/sup -1/ and coupling-limited quality factors of greater than 10/sup 5/ are observed from 200-/spl mu/m-radii ring resonators. The measured spectral linewidth is as narrow as 0.0145 nm.     

Wavelength and Waveband Assignment for Ring Networks Based on Parallel Multi‐granularity Hierarchical OADMs

In this paper we study the optimization issues of ring networks employing novel parallel multi‐granularity hierarchical optical add‐drop multiplexers (OADMs). In particular, we attempt to minimize the number of control elements for the off‐line case. We present an integer linear programming formulation to obtain the lower bound in optimization, and propose an efficient heuristic algorithm called global bandwidth resource assignment that is suitable for the design of large‐scale OADM networks.     

Fatigue crack growth in SiC particulates reinforced Al matrix graded composite

The SiC/Al graded composite was fabricated by powder metallurgy processing and its fatigue crack growth behavior was studied. The volume percentage of SiC particulates was distributed from 5 to 30% layer by layer on the cross section. Since the aluminium was dissolved together, there was no evident interface between the two layers with different volume fraction of SiC particulates. Fatigue crack growth was in direction of from 5 to 30% SiC layers under sinusoidal wave-form. The retardation of fatigue crack growth was found when crack propagated from low volume fraction of SiC to high volume fraction of SiC. The crack deflection and branching between two layers were observed, which decreased crack growth rates. In view of crack tip driving force, the plasticity mismatch between the layers shielded crack tip driving force, i.e. decreased the effective J-integral at the tip of the crack as the plastic zone of the crack tip spread from the weaker material into the stronger material.     

一种基于空间到达角的卫星电子侦察信号分选方法

在建立简化的卫星电子侦察空间模型的基础上，提出了一种利用空间到达角分选卫星电子侦察信号的新方法。通过仿真实验验证了这种方法的可行性。该方法可用于密集信号的预处理。     

基于FPGA的CAVLC编解码器设计与实现

H．264标准在基本档次和扩展档次中采用CAVLC熵编码，完成对变换系数残差块的编码。提出一种基于FPGA的H．264标准的CAVLC编解码器，程序代码用verilog硬件描述语言编写，并在QuartusⅡ中进行了仿真验证，可以实现对每个残差块数据的编解码并将其按照宏块光栅扫描的顺序输出到存储器，因此适合于嵌入在最终的码流中。仿真结果表明此CAVLC编解码器达到H．264标准中基本档次和扩展档次level3．0的性能要求。     

火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。