破乳剂与原油管道混合流动的数值模拟

原油开采过程中,原油遇水能够形成比较稳定的乳化液,添加破乳剂是快速高效脱去原油中水的最有效的方法。对破乳剂与原油两相混合的流动形态进行了数值模拟,得出破乳剂在不同速度、不同入口角度下加入原油管道后两相流动的速度分布图和浓度分布图。经过对比发现,当药剂入口角度为0°,药剂流入速度越大,越有利于破乳剂的扩散,破乳剂和原油的混合效果最好,就更有利于原油的脱水。     

Engineering all-aromatic polyamide surface from hydrophilic to superhydrophobic and the accelerated strategy

Being a new kind of nanomaterials, aromatic polyamide nanofibers (ANF) have been much highlighted in recent studies. We here demonstrate an isopropyl alcohol (IPA) accelerated chemical cleavage on poly (p-phenylene terephthalamide) chopped fibers, which provides an efficient preparation method of ANF. The comprehensive study on the processes accelerated by different alcohols revealed that the preparation time of ANF in the mixed medium of dimethyl sulfoxide (DMSO)-alcohol (20:1 in volume) was shorten to 45 min and 75 min for methanol (ethanol) and isopropanol, respectively. However, the nanofibers prepared in DMSO-IPA exhibited the minimum in axial and radial dimensions, providing the finest and most uniform diameter of 16 nm. The corresponding ANF films through vacuum assisted filtration also showed the highest tensile strength of 150 MPa, in comparison with those of the ANF films prepared using other alcohols, which were about 110 MPa. Furthermore, ANF/silicon hybrid films were prepared by the ionic ring-opening reaction followed by the alkoxysilane condensation and nanoparticle fabrication. By changing the organo functional groups in the alkoxysilane, the surface of the films were adjustable in a wide contact angle range from 56° (hydrophilic) to 150° (superhydrophobic), suggesting the amendable interfacial properties potential applicable to composite fabrication with most of the resin matrix.     

数控车床受迫振动特性仿真分析

由于偏心力的作用，数控车床车削过程中将产生振动。为了提高加工精度，必须对数控车床的振动进行控制。所以，建立了数控车床受迫振动的一自由度弹簧——质量——阻尼系统力学模型，以及相应的数学模型与Simulink仿真模型，从而对其振动特性进行分析。结果表明：当数控车床受到偏心力作用时，其振动由三部分组成。通过对各组成部分的物理意义的分析，提出了振动控制方法。     

橡胶冲裁模具刃口间隙的探讨与研究

阐述了合理选择丁基橡胶瓶塞冲裁模具的刃口间隙是提高模具使用寿命的关键，介绍了模具刃口间隙的确定方法。     

奥氏体化温度及冷却方式对20Mn2SiVB钢组织及性能的影响

通过各种试验手段,研究了20Mn2SiVB钢不同奥氏体化温度及不同冷却方式处理后其显微组织及其强度和塑性的变化,确定了最佳的热处理工艺。结果表明:900℃奥氏体化后风冷时钢的强塑性最好;在强塑性最佳时的微观组织是铁素体+粒状贝氏体。     

医用钴基合金的组织结构及耐腐蚀性能

以锻造CoNiCrMo，CoCrMo和CoCrMoC台会为研究对象，通过金相观察，XRD分析和耐腐蚀试验，研究了3组合金在不同热处理条件下的显微结构，相成分及在Hi同溶液中的耐腐蚀性能。结果表明：2组锻造合金的再结晶温度都是1000℃，且晶粒尺寸随着固溶温度升高和时效时间延长而逐渐变大。3组试样在NaCl溶液中为钴基合金典型的阳极极化曲线；在Hanks’溶液中均有一个二次钝化行为，且锻造CoNiCrMo合金的二次钝化区域较窄，而其他2组合金则较宽；在含柠檬酸三钠的溶液中过钝化电位降低，柠檬酸盐的存在降低了含金的耐腐蚀性能。热处理对合金的耐腐蚀性能影响不大。     

Formation and thermal stability of amorphous Ni-Mo-P alloys

The experimental researches on the chemical deposition of Ni-Mo-P amorphous alloys were carried out by adding Na2 MoO4 into acidic solutions. The optimum technology conditions were obtained by orthogonal design experiments. The structures and the relationship between compositions and their thermal stability were studied by energy spectrum (EC), scanning electron micrograph and X-ray diffraction spectrum. Compared with Ni-P amorphous alloys, the Ni-Mo-P amorphous alloys have high crystallization temperature and thermal stability, and the hardness reaches its peak when the annealing temperature is 500 ℃. With the increase of the heat treatment temperature, the surface morphology of the alloys changes.     

一种新型气硬冷芯盒树脂砂工艺试验及其在生产中的应用

原砂加入2．5％水溶性酚醛树脂，固化剂为甲酸甲脂，加入量占树脂的30％～40％。先把甲酸甲脂在气体发生器中气化，然后再与40％的压缩空气混合，吹气硬化制芯，最高抗拉强度1．2MPa，抗压强度0．32MPa，发气量12mL／g。生产浇注试验表明：砂芯表面光洁，轮廓清晰，尺寸精确，铸件缺陷少，无毒或低毒，和一般冷硬树脂砂比较，成本降低30％。     

多目标优化理论在蜂窝夹芯结构设计中的应用

在确定了设计变量及目标函数的基础上,根据结构本身的要求,推导出用于多目标优化的5个约束条件.根据多目标优化理论,采用乘除法对蜂窝夹芯结构进行了评价函数的构造,并用VC语言编制了钢质蜂窝夹芯减振板结构的优化程序,该程序可实现结构尺寸及性能的优化,并计算出各目标函数的最终值.