Electrical properties and positron annihilation study of (Ba<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Ho<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>)TiO<Subscript>3</Subscript> ceramics

DC resistivity, dielectric constant, dielectric loss and positron annihilation spectra of (Ba_1−x Ho _x )TiO₃ ceramics have been measured as a function of holmium concentration x. It has been found that the DC resistivity of (Ba_1−x Ho _x )TiO₃ is strongly dependent on the Ho content: it decreases three orders of magnitude and reaches a minimum at x = 0.4%. Doping with 0.6% holmium increases the permittivity of BaTiO₃ by approximately three times (from ∼1,300 to ∼4,000), with only a slight increase in the corresponding dielectric loss. The local electron density and defect concentration estimated using positron annihilation technique conforms well to the features found in the dielectric and resistivity measurements. The results have been discussed in terms of a mixed compensation model.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

（1S，2S，5R）-薄荷基取代烯烃的合成

以(L)-薄荷基氯为原料,通过薄荷基氯化镁分别与烯丙基溴、2-甲基-3-氯丙烯、1-溴-3-甲基-2-丁烯在Cul催化下发生偶联反应,首次合成了3-(1S,2S,5R)-薄荷基-1-丙烯,2-甲基-3-(1S,2S,5R)-薄荷基-1-丙烯和2-甲基-4-(1S,2S,5R)-薄荷基-2-丁烯,总收率分别为80.5%、83.1%和79.6%.探讨了影响反应的多种因素,找到了较好的合成条件,并用IR、 1HNMR和元素分析对产物进行了表征.     

复合聚全氟乙丙烯材料的介电及高频击穿性能研究

在聚全氟乙丙烯(FEP)中添加 TiO_2和 Al_2O_3,通过热压成型的方法制备了 FEP/TiO_2复合材料和 FEP/Al_2O_3复合材料,研究了氧化物添加量对复合材料介电常数、介电损耗和高频击穿性能的影响。结果表明,随氧化物含量的增加,复合材料的介电常数和介电损耗均增加;在同一添加量下,TiO_2对复合体系的介电性能影响较大。FEP/TiO_2复合材料的高频击穿性能随 TiO_2含量的增加而下降,在 TiO_2含量为4.0%(质量分数,下同)时,复合材料的损伤阈值已降为 FEP 材料损伤阈值的48.9 %。而 FEP/Al_2O_3复合材料的高频击穿性能随 Al_2O_3含量的增加而升高,当 Al_2O_3含量为1.2%时,复合材料的损伤阈值已增大到 FEP 材料损伤阈值的2倍,达到313 J/m~2。     

清华屏蔽实验反应堆中子注量率能谱的调节和测量

叙述了采用多种屏蔽过滤方法,通过实验获得多种条件下的中子注量率能谱的调节和测量。     

雷达仿真系统中电磁干扰环境的仿真设计和实施

雷达仿真系统是为检测雷达设备的抗干扰能力以及在各种电磁环境下的工作性能而设计的，包括有源干扰和无源干扰的模拟仿真。本文阐述了无源干扰即杂波的散射模型和仿真过程；从同步脉冲干扰的基本原理出发，阐明在雷达工作环境仿真系统中距离拖引、速度拖引、虚假目标等同步脉冲有源干扰的设计和实施过程；并针对工作在搜索和跟踪交替模式下的相控阵雷达提出自适应综合干扰方式；最后分析并总结了系统仿真时为真实、有效地模拟电磁干扰环境应注意的关键问题。     

Fuel management of the HTR-10 including the equilibrium state and the running-in phase

The mode of fuel management of the HTR-10 was studied, including the simulation of the fuel shuffling process and the measurement of the burnup of a fuel element. The prior consideration was the design of the equilibrium state. Based on this the fuel loading of the initial core and the fuel shuffling mode from the initial core through the running-in phase into the equilibrium state were studied. The code system VSOP was used for the physical layout of the HTR-10 at the equilibrium state and in the running-in phase. For the equilibrium state, in order to lessen the difference between the peak and the average burnup, 5-fuel-passage-through-the-core was chosen for the fuel management. The average burnup of the spent fuel for the equilibrium core is 80 000 MWd t⁻¹, and the peak value of it is less than 100 000 MWd t⁻¹ when the burnup of the recycled fuel element is under 72 000 MWd t⁻¹. The mixture of fuel element and graphite element was used for the initial core loading, the volume fractions of the fuel and the graphite elements were 0.57 and 0.43, respectively. During the running-in phase, the volume fraction of graphite will decrease with the fresh fuel elements being loaded from the top of the core and the graphite elements discharged from the bottom of the core. The fuel shuffling mode is similar to that of the equilibrium state. The burnup limit of recycled fuel element is also 72 000 MWd t⁻¹ and the peak burnup is less than 100 000 MWd t⁻¹. Finally the core will be full of fuel elements with a certain profile of burnup and reaches the equilibrium state. According to the characteristics of the pebble-bed high temperature gas-cooled reactor, a calibrating method of concentration of ¹³⁷Cs was proposed for the measurement of fuel burnup.     

光纤的淬冷增强原理

本文从拉丝工艺技术的角度出发，讨论了高速、高温拉丝工艺方法对光纤的淬冷增强原理。     

Penicilloyl peptides are recognized as T cell antigenic determinants in penicillin allergy

Although hapten immune responses have been intensively studied in the mouse, very little is known about hapten determinants involved in human allergic reactions. Penicillins, as chemically reactive compounds of low molecular weight, constitute typical examples of hapten allergens for humans. Penicillins become immunogenic only after covalent binding to carrier proteins and in this form frequently induced IgE-mediated allergic reactions in patients subjected to antibiotic treatment. However, our previous data strongly indicated that penicillins also form part of the epitopes contacting the antigen receptors of beta lactam-specific T cells in allergic individuals. We have therefore investigated the molecular constraints involved in the T cell immune response to penicillin G (Pen G). Designer peptides containing a DRB1*0401-binding motif and covalently modified with Pen G via a lysine epsilon-amino group were found to induce proliferation of Pen G-specific T cell clones. A precise positioning of the hapten molecule on the peptide backbone was required for optimal T cell recognition. Furthermore, we extended these observations from our designer peptides to show that a peptide sequence derived from a natural DRB1*1101-binding peptide modified in vitro with Pen G, also acquired antigenic properties. Our data for the first time provide insight into the manner in which allergenic haptens are recognized by human T cells involved in allergic reactions to drugs and suggest possible mechanisms leading to the onset of these adverse immune responses.     

焊接史

本文追溯了19世纪末发明的电弧焊接的历史。当Oscar Kjellberg成立伊萨公司以探索他发明的涂层焊条时，伊萨从一开始就和电弧焊的发展结下了不解之缘。