抚顺乙烯脱甲烷塔改造

通过乙烯装置脱甲烷塔系统改造后的运行状况的分析，对脱甲烷塔改造后的运行状态进行了总结，并为更进一步的优化工艺条件提出措施。     

基体树脂对长玻璃纤维增强PP力学性能的影响

采用在线混合设备制备了长玻璃纤维(LGF)增强聚丙烯(PP)复合材料(LGF-PP),研究了基体性质及界面相容剂对LGF-PP力学性能的影响。基体树脂熔体流动速率的增加,使最终LGF-PP中的玻璃纤维长度从5.63 mm增至8.56 mm,提高了力学性能。与均聚PP比较,以共聚PP为基体树脂的LGF-PP冲击强度高出约10%,但其他性能略差。界面相容剂有利于增强玻璃纤维与PP的界面结合,拉伸强度和拉伸模量明显增加,但是冲击强度降低了20%～30%。     

纳米陶瓷的烧结研究

纳米陶瓷的制备过程中，烧结是关键一环。总结了现有的烧结理论，介绍了国内外流行的纳米烧结技术，并提出了今后的研究方向。     

尿素改性热塑性酚醛树脂的合成及应用

先用尿素、甲醛合成二羟甲脲，然后在酸性介质下把二羟甲脲滴加在苯酚中反应合成尿素改性的热塑性酚醛树脂。研究了反应浑浊点和二羟甲脲的滴加速度，同时研究了二羟甲脲与苯酚的尿酚比与物料的出料温度、产品产率及树脂理化性能指标的关系。结果表明：（1）二羟甲脲滴加速度的合适范围是0．012－0．029mol/mol.min；（2）本树脂的出料温度为125℃以下；（3）产品收率，游离酚，软化点随尿比的增长而递增，凝胶速度变化不大。另介绍了这种树脂在酚醛模塑料中的应用。     

Ways of strengthening biodegradable soy‐dreg plastics

Biodegradable plastics (GSD) based on soy dreg (SD) were prepared by compression‐molding, with glycerol as the plasticizer and glutaraldehyde (GA) as the cross‐linker. The structure and properties of the GSD sheets were investigated by Fourier‐transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), scanning electron microscope (SEM), and tensile test methods. The results indicate that when GA content was 6.8%, the tensile strength (σ_b) of the sheet reached the maximum value of 14.5 MPa. Moreover, the strength and water resistance of the sheets coated with castor‐oil‐based polyurethane/nitrochitosan interpenetrating network (IPN) coating were significantly enhanced to 24.6 MPa in the dry state and 9.8 MPa in the wet state. Simultaneously, the test of biodegradability of the GSD sheet in a mineral salts medium containing microorganisms and agar proved that GSD could be fully biodegradable. This work has provided a novel way to utilize low‐cost SD to prepare biodegradable plastics. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 422–427, 2003     

Novel Method To Optimize the Structure of Reticulated Porous Ceramics

A novel method has been developed for the fabrication of silicon nitride reticulated porous ceramics (RPCs) with regulated structure, using polyurethane sponge as the template. This technique includes two centrifuging steps. In the first stage, the polyurethane sponges are coated with thin slurry through high-speed centrifuging. After the slurry on sponges dried, a high-strength green body without filled cells is obtained. In the second stage, because of improved adhesion between the body and the slurry after the first coating, the body with uniformly thick strut is produced by recoating the as-prepared green body with thixotropic slurry and centrifuging again. The loading content of slurry and the pore diameter of the RPCs body greatly depend on the slurry viscosity in the process of recoating. The strut diameter and pore diameter of the RPCs are effectively optimized by modulating the slurry viscosity.     

古马隆树脂型聚氨酯防水涂料

介绍一种以古马隆树脂改性的新型双组分聚氨酯防水涂料，并对其原材料的选择、配方、生产工艺等方面进行了研究。     

高职院校无线网络的规划与设计

高职院校一般规模比较小,WLAN就比较适合这个范围使用,通过无线网络可以很好的弥补目前有线网络的不足,使教职工和学生可以随时随地的进行网上办公和学习。通过需求分析,找到网络架设的重点;通过无线网络的安全性分析,使学校在购买相关设备的时候可以有所参考;通过无线网络的管理,使大家深刻认识到网络管理的重要性。     

Charge/discharge characteristics of sulfur composite cathode materials in rechargeable lithium batteries

The charge and discharge characteristics of lithium batteries with sulfur composite cathodes have been investigated. The sulfur composites showed novel electrochemical characteristics. The analysis of the differential capacity indicated that the discharge process showed two voltage plateaus of 2.10 V and 1.88 V, and the charge process also presented two voltage plateaus of 2.22 V and 2.36 V. The overcharge test showed that the composite cannot be charged over 4.0 V, the voltage always stopped at about 3.9 V during charging, indicating that the composite presented the intrinsic safety for the overcharge of lithium batteries. The overcharge can cause serious safety problem for the conventional Li-ion batteries. The overcharge test also showed that the batteries with sulfur composite were destroyed when the upper cut-off voltage was over 3.6 V. However, the composite presented good reversible capacity after it was deep discharged even to 0 V. It showed stable cycleability and high cycling capacity of 1000 mAh g⁻¹ when cycling between 0.1 V and 3.0 V, indicative of the different characteristic from the conventional oxide cathode materials. The prototype polymer battery with the composite cathode material presented the energy density of 246 Wh kg⁻¹ and 401 Wh L⁻¹.     

大学生党支部建在班上的实践与思考

以漳州师范学院为例,总结了党支部建在班上的实践经验,并对大学生班级党支部的设置方式、工作模式和内涵建设进行了思考.