A novel frequency-offset monitoring technique for direct-detection DPSK systems

We propose and demonstrate a novel technique to monitor the frequency offset between the optical source and delay interferometer (DI) for direct-detection differential phase-shift-keying (DPSK) systems. In this scheme, a phase-modulated tone is applied to DPSK signals at the transmitter and then detected after being converted into an amplitude-modulated tone at the DI to be used for the monitoring signal. Our experimental demonstration shows that the monitoring range and sensitivity of the proposed scheme are measured to be /spl plusmn/2 GHz and /spl sim/10 MHz, respectively, which we believe are good enough to be used either to generate alarm signals for the frequency offset monitoring or to control the feedback loop of the DI.     

A miniature UWB planar monopole antenna with 5-GHz band-rejection filter and the time-domain characteristics

A planar monopole antenna with a staircase shape and small volume (25/spl times/26/spl times/1 mm/sup 3/) is proposed in this paper. With the use of a half-bowtie radiating element, the staircase-shape, and a modified ground plane structure, the proposed antenna has a very wide impedance bandwidth measured at about 11.6 GHz (2.9-14.5 GHz, bandwidth ratio about 1:5) below VSWR 2 including the WLAN band notched in the vicinity of 5 GHz. An omnidirectional radiation pattern is obtained. The group delay which is an indication of linearity between two proposed antennas is less than 1 ns. The electrical characteristics in terms of frequency and time domains and physical ones of the proposed antenna make it attractive for use in ultrawideband (UWB) systems.     

An all-optical 2R regenerator using a compact self-seeded Fabry-Pe/spl acute/rot laser diode incorporated in a bidirectional EDFA

An all-optical 2R regenerator, based on a compact self-seeded Fabry-Pe/spl acute/rot laser diode with a 10-mm-long embedded fiber Bragg grating cavity, and a bidirectional erbium-doped fiber amplifier, is proposed and experimentally demonstrated to execute all-optical 2R regeneration at 10 Gb/s. Compared with the conventional 1R regeneration, the proposed scheme has achieved significant 6.4-dB improvement of power penalty at bit-error ratio =10/sup -9/ in the transmission experiment over 100-km standard single-mode fiber.     

A study of Cu/Low-k stress-induced voiding at via bottom and its microstructure effect

Microstructure effect of Cu/low-k interconnect, which is substantially affected by process condition or manufacturing deviation, is a dominated factors for copper stress and critical to the formation of stress-induced voiding (SIV). In this work, SIV at via bottom is studied in the aspects of thickness variation of copper interconnect and low-k dielectric. Besides, via-related factors consist of via profile and dimension are also involved in SIV sensitivity studies. With the assistance of finite element analysis (FEA), Cu stress in terms of different Cu/low-k microstructure scenarios are modelled to understand the voiding evolution and explore the their dependence with SIV susceptibility. Meanwhile, microstructure effects with and without redundant via are also simulated to evaluate their impacts on SIV immunity.     

Structural reliability assessment of multi-stack package (MSP) under high temperature storage (HTS) testing condition

Wire ball open failure at the interface of the gold wire and bonding pad of a multi-stack package (MSP) under high temperature storage (HTS) condition of 150 °C is studied. Failure analysis using FIB-SEM was conducted by in-plane moiré interferometry and FEA to clarify the failure mechanism. The ball open failure due to Kirkendall void that results from metal diffusion at high temperature was accelerated by the tensile stress imposed at the gold wire. The tensile stress developed at the gold wire when packages showing different warpage behaviours were stacked. Mechanical interaction between top and bottom packages caused unstable warpage, readily twisted and saddled. The wire came in contact with the photo-sensitive solder resist (PSR) dam because of the unstable warpage and this contact resulted in tensile stress at the gold wires. Solder flux residues reacted with the encapsulant, and as a result, the encapsulant of the top package adhered to the chip of the bottom package, and this adherence created additional tensile stress at the gold wires. To reduce the tensile stress at the wires, the PSR dam was removed, loop shape was altered from 45° to 90°, water soluble flux was applied, and cleaning process was added. HTS reliability was significantly improved and guaranteed after reducing the tensile stress at the wires.     

Similarity-based interference during language comprehension: Evidence from eye tracking during reading.

The nature of working memory operation during complex sentence comprehension was studied by means of eye-tracking methodology. Readers had difficulty when the syntax of a sentence required them to hold 2 similar noun phrases (NPs) in working memory before syntactically and semantically integrating either of the NPs with a verb. In sentence structures that placed these NPs at the same linear distances from one another but allowed integration with a verb for 1 of the NPs, the comprehension difficulty was not seen. These results are interpreted as indicating that similarity-based interference occurs online during the comprehension of complex sentences and that the degree of memory accessibility conventionally associated with different types of NPs does not have a strong effect on sentence processing. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Non‐linear finite element modal approach for the large amplitude free vibration of symmetric and unsymmetric composite plates

A theoretical analysis is presented for the large amplitude vibration of symmetric and unsymmetric composite plates using the non‐linear finite element modal reduction method. The problem is first reduced to a set of Duffing‐type modal equations using the finite element modal reduction method. The main advantage of the proposed approach is that no updating of the non‐linear stiffness matrices is needed. Without loss of generality, accurate frequency ratios for the fundamental mode and the higher modes of a composite plate at various values of maximum deflection are then determined by using the Runge–Kutta numerical integration scheme. The procedure for obtaining proper initial conditions for the periodic plate motions is very time consuming. Thus, an alternative scheme (the harmonic balance method) is adopted and assessed, as it was employed to formulate the large amplitude free vibration of beams in a previous study, and the results agreed well with the elliptic solution. The numerical results that are obtained with the harmonic balance method agree reasonably well with those obtained with the Runge–Kutta method. The contribution of each linear mode to the maximum deflection of a plate can also be obtained. The frequency ratios for isotropic and composite plates at various maximum deflections are presented, and convergence of frequencies with the number of finite elements, number of linear modes, and number of harmonic terms is also studied. Copyright © 2005 John Wiley & Sons, Ltd.     

Shape optimization of flow guides in three‐dimensional extrusion processes by an approximation scheme based on state variable linearization

A new scheme of shape optimization is applied to the design of a flow guide in flat‐die extrusion processes. In general, tremendous time is inevitably required for the optimization of large‐scale three‐dimensional extrusion processes. This is because the finite element analysis requires large computation time owing to the complexity of the die geometry and flow behaviour. The proposed scheme effectively reduces the computation time for the optimization process by approximating the objective function. This is achieved by introducing a transformed equation of the state variables. The scheme is then applied to the practical extrusion processes to produce ‘l’, ‘H’ and ‘L’ sections. The objective of the optimization is to make a balanced flow of the material in the exit region. Control points of a Bezier curve describing the outline of the flow guide are regarded as the design variables. Through application to large‐scale problems, the effectiveness and usefulness of the proposed scheme is demonstrated. Copyright © 2005 John Wiley & Sons, Ltd.     

Recent Progress in the Synthesis of Porous Carbon Materials

In this review, the progress made in the last ten years concerning the synthesis of porous carbon materials is summarized. Porous carbon materials with various pore sizes and pore structures have been synthesized using several different routes. Microporous activated carbons have been synthesized through the activation process. Ordered microporous carbon materials have been synthesized using zeolites as templates. Mesoporous carbons with a disordered pore structure have been synthesized using various methods, including catalytic activation using metal species, carbonization of polymer/polymer blends, carbonization of organic aerogels, and template synthesis using silica nanoparticles. Ordered mesoporous carbons with various pore structures have been synthesized using mesoporous silica materials such as MCM‐48, HMS, SBA‐15, MCF, and MSU‐X as templates. Ordered mesoporous carbons with graphitic pore walls have been synthesized using soft‐carbon sources that can be converted to highly ordered graphite at high temperature. Hierarchically ordered mesoporous carbon materials have been synthesized using various designed silica templates. Some of these mesoporous carbon materials have successfully been used as adsorbents for bulky pollutants, as electrodes for supercapacitors and fuel cells, and as hosts for enzyme immobilization. Ordered macroporous carbon materials have been synthesized using colloidal crystals as templates. One‐dimensional carbon nanostructured materials have been fabricated using anodic aluminum oxide (AAO) as a template.